GPC130 GLOBAL PERFORMANCE SWITCHERS
FEATURES:
• Wide-range AC input 85-264VAC
• 2-year warranty
• Approved to UL1950, IEC950, EN60950 and CSA22.2-
234 L3
• Exceeds FCC and CISPR22 Class B conducted
emissions requirements
• Multiple outputs
• For medical version, see p. 92
marked to LVD
•
GLOBAL PERFORMANCE SWITCHERS
SPECIFICATIONS:
AC Input
85-264Vac, 47-63Hz single phase.
Input Current
Maximum input current at 120Vac, 60Hz with full rated output load: 3.5A
Hold-Up Time
20mSec minimum from loss of AC input at full load, nominal line (115Vac).
Output Power
100W continuous, 165W peak; 130 with 26 cfm air flow. Peak ratings are
for 60 sec. maximum duration, 10% duty cycle. During peak load
condition, output regulation may exceed total regulation limits.
Overload Protection
Fully protected against short circuit and output overload. Short circuit
protection is cycling type power limit on outputs 1 & 2; foldback type on
outputs 3 & 4. Recovery after fault is automatic. See output ratings chart
for additional notes or conditions.
Overvoltage Protection
Main outputs: 124%
±
12% typical.
Efficiency
70% at full rated load, nominal input voltage, depending on model and
load distribution.
Turn-on Time
Less than 1 second at 120VAC, 25°C (inversely proportional to input
voltage and thermistor temperature).
Input Protection
Internal AC fuse provided. Designed to blow only if a catastrophic failure
occurs in the unit.
Inrush Current
Inrush is limited by internal thermistors. Inrush at 240VAC under cold start
conditions will not exceed 34A.
Temperature Coefficient
0.03%/ºC typical on all outputs.
Environmental
Designed for 0 to 50°C operation at full rated output power; derate
output current and total output power by 2.5% per
°C
above 50°C. See
Environmental and Packaging Specifications (p. 11) for additional
information.
Power Fail
TTL- or CMOS-compatible output goes low (< 0.5V) 5mSec before
output voltage drops more than 4% below nominal voltage upon loss of
AC power. The signal is factory set to trip on 84 to 94VAC brown-out
depending upon incoming line impedance and distortion. Other settings
are available to the user through adjustment of built-in potentiometer
(consult factory for assistance).
No-Load Turn-on/Standby
No degradation of reliability will occur.
Output Noise
0.5% RMS, 1% Pk-Pk, 20MHz bandwidth, differential mode. Measured
with noise probe directly across output terminals of the power supply.
Transient Response
Main output—500µSec typical response time for return to within 0.5% of
final value for a 50% load step change.
∆i/∆t<0.2A/µSec.
Maximum
voltage deviation is 3.5%. Startup/shutdown overshoot less than 3%.
Remote Sense
Provided as a standard feature on output 1.
Voltage Adjustment
Built-in potentiometer adjusts voltage
±5%
on outputs 1 & 2.
Reverse Voltage Protection
All outputs protected against inadvertent application of reverse voltage up
to 1 times rated current of the reverse output.
Overload Protection
Factory set to begin power limiting at approximately 170W.
EMI/EMC Compliance
All models include built-in EMI filtering to meet the following emissions
requirements:
EMI SPECIFICATIONS
COMPLIANCE LEVEL
Conducted Emissions
EN55022 Class B; FCC Class B
Static Discharge
EN61000-4-2, 6 kV contact, 8 kV air
RF Field Susceptibility
EN61000-4-3, 3 V/meter
Fast Transients/Bursts
EN61000-4-4, 2 kV, 5 kHz
Surge Susceptibility
EN61000-4-5, 1 kV diff., 2 kV com.
Leakage Current
0.7mA. 254Vac @ 60Hz input.
Safety
Approved to UL1950, CSA22.2 No. 234 Level 3, IEC950 and EN60950.
UL file #E135803 commercial; CSA #LR46516 all models. The output(s)
are intended for safety earthed Signal Output and Intermediate Circuits
only. All DC outputs are SELV under normal and single fault conditions.
Condor D.C. Power Supplies, Inc./A subsidiary of SL Industries, Inc.
2311 Statham Parkway, Oxnard, CA 93033 • 800-235-5929 • 805-486-4565 • FAX 805-487-8911 • www.condorpower.com/
26
Model
GPC130A
Output No.
1
2
3
4
1
2
3
4
1
2
3
4
1
2
3
4
1
2
3
4
Output
+5V
+12V
-12V
+12V
+ 5V
+12V
-5V
-12V
+5V
+12V
-15V
+15V
+5V
+24V
-12V
+12V
+5V
+24V
-15V
+15V
Output
Minimum
3A
0A
0A
0A
3A
0A
0A
0A
3A
0A
0A
0A
3A
0A
0A
0A
3A
0A
0A
0A
Output
Maximum (B)
16A
5A
1.2A
1.2A
16A
5A
1.2A
1.2A
16A
5A
1.2A
1.2A
16A
3.5A
1.2A
1.2A
16A
3.5A
1.2A
1.2A
Output
Maximum (C)
20A
5A
1.2A
1.2A
20A
5A
1.2A
1.2A
20A
5A
1.2A
1.2A
20A
3.5A
1.2A
1.2A
20A
3.5A
1.2A
1.2A
Output Peak
25A
8A
1.5A
1.5A
25A
8A
1.5A
1.5A
25A
8A
1.5A
1.5A
25A
5A
1.5A
1.5A
25A
5A
1.5A
1.5A
Noise P-P
50mV
120mV
120mV
120mV
50mV
120mV
50mV
120mV
50mV
120mV
150mV
150mV
50mV
240mV
120mV
120mV
50mV
240mV
150mV
150mV
Total
Regulation (A)
2%
2%
3%
3%
2%
2%
3%
3%
2%
2%
3%
3%
2%
2%
3%
3%
2%
2%
3%
3%
GPC130B
GPC130C
GPC130D
GPC130E
A. Total regulation is defined as the maximum deviation from the nominal voltage for all steady-state conditions of initial voltage setting, input line voltage and output load.
B. Unrestricted natural convection cooling.
C. Requires 26cfm moving air.
GPC130 MECHANICAL SPECIFICATIONS:
INPUT:
J1:
AMP P.C.B. HEADER P/N 640445-5
8.50 [215.90mm]
8.000 [203.20mm]
PIN 1)
PIN 2)
PIN 3)
AC LINE
N/C
AC NEUTRAL
AC LINE
AC NEUTRAL
AC GROUND
N/C
+ SENSE
- SENSE
POWER FAIL
PIN 4)
PIN 5)
N/C
AC GROUND
MATING CONNECTOR AMP P/N
HOUSING 640250-5
CONTACTS 770522-1
TB1:
[32.46
±
0.51]
1
1.278
±
0.20
3
J1
5
1
TB1
F1
OUT 2
V.ADJ
1
J3
TB2
1
0.375 X 6-32 TERMINAL BLOCK
PIN 1)
PIN 2)
PIN 3)
PIN 1)
PIN 2)
PIN 3)
PIN 4)
1
16
SIGNALS:J2
1.944
[49.38mm]
AMP P.C.B. HEADER P/N 640456-4
4.50
[114.30mm]
8
9
T3
OUT1
V.ADJ
MATING CONNECTOR AMP P/N 640440-4
16
J2
1
4
OUTPUT:
J3:
AMP P.C.B. HEADER P/N 1-640445-6
PIN 1)
PIN 2)
PIN 3)
PIN 4)
PIN 5)
PIN 6)
PIN 7)
PIN 8)
OUTPUT #4
OUTPUT #4
OUTPUT #3
OUTPUT #3
OUTPUT #2
OUTPUT #2
COMMON
COMMON
PIN 9)
PIN 10)
PIN 11)
PIN 12)
PIN 13)
PIN 14)
PIN 15)
PIN 16)
COMMON
COMMON
COMMON
COMMON
OUTPUT #1
OUTPUT #1
OUTPUT #1
OUTPUT #1
6-32 MTG
(0.125 [3.18mm] MAX SCREW PENETRATION)
4 PLCS
0.25
[6.35mm]
PF ADJ
6-32 MTG
4 PLCS
0.12 [3.05mm]
MATING CONNECTOR AMP P/N
HOUSING 1-640250-6
CONTACTS 770522-1
2.00
[50.80mm]
[32.46
±
0.51]
XFMR (T3) PROTRUDES
IN THIS AREA ONLY.
1.278
±
0.20
TB2:
0.375 X 6-32 TERMINAL BLOCK
PIN 1)
PIN 2)
PIN 3)
PIN 4)
OUTPUT #4
OUTPUT #3
OUTPUT #2
COMMON
PIN 5)
PIN 6)
PIN 7)
PIN 8)
COMMON
COMMON
OUTPUT #1
OUTPUT #1
OPTIONAL COVER AVAILABLE, ORDER P/N 08-30466-1130
OPTION: ADD "-T" SUFFIX TO PART NUMBER FOR
6-32 SCREW TERMINAL BLOCK ON I/O
WEIGHT: 2.3 LBS MAX. [1.05 kg]
TOLERANCES: X.XX=0.030 [0.76mm]
X.XXX=0.010 [0.25mm]
Condor D.C. Power Supplies, Inc./A subsidiary of SL Industries, Inc.
2311 Statham Parkway, Oxnard, CA 93033 • 800-235-5929 • 805-486-4565 • FAX 805-487-8911 • www.condorpower.com/
27
GLOBAL PERFORMANCE SWITCHERS
Embedded System
京公网安备 11010802033920号
EEWORLD
