a high performance, asynchronous, radiation-hardened, 32K x 8
programmable memory device. The UT28F256LVQL PROM
features fully asychronous operation requiring no external clocks
or timing strobes. An advanced radiation-hardened twin-well
CMOS process technology is used to implement the
UT28F256LVQL. The combination of radiation-hardness, fast
access time, and low power consumption make the
UT28F256LQL ideal for high speed systems designed for
operation in radiation environments.
A(14:0)
DECODER
MEMORY
ARRAY
SENSE AMPLIFIER
CE
PE
OE
PROGRAMMING
CONTROL
LOGIC
DQ(7:0)
Figure 1. PROM Block Diagram
1
DEVICE OPERATION
The UT28F256LVQL has three control inputs: Chip Enable
(CE), Program Enable (PE), and Output Enable (OE); fifteen
address inputs, A(14:0); and eight bidirectional data lines,
DQ(7:0). CE is the device enable input that controls chip
selection, active, and standby modes. Asserting CE causes I
DD
to rise to its active value and decodes the fifteen address inputs
to select one of 32,768 words in the memory. PE controls
program and read operations. During a read cycle, OE must be
asserted to enable the outputs.
PIN CONFIGURATION
A14
A12
A7
A6
A5
A4
A3
A2
A1
A0
DQ0
DQ1
DQ2
V
SS
1
2
3
4
5
6
7
8
9
10
11
12
13
14
28
27
26
25
24
23
22
21
20
19
18
17
16
15
V
DD
PE
A13
A8
A9
A11
OE
A10
CE
DQ7
DQ6
DQ5
DQ4
DQ3
PIN NAMES
A(14:0)
CE
OE
PE
DQ(7:0)
Address
Chip Enable
Output Enable
Program Enable
Data Input/Data Output
Table 1. Device Operation Truth Table
1
OE
X
0
1
1
PE
1
1
0
1
CE
1
0
0
0
I/O MODE
Three-state
Data Out
Data In
Three-state
MODE
Standby
Read
Program
Read
2
Notes:
1. “X” is defined as a “don’t care” condition.
2. Device active; outputs disabled.
ABSOLUTE MAXIMUM RATINGS
1
(Referenced to V
SS
)
SYMBOL
V
DD
V
I/O
T
STG
P
D
T
J
Θ
JC
I
I
PARAMETER
DC supply voltage
Voltage on any pin
Storage temperature
Maximum power dissipation
Maximum junction temperature
Thermal resistance, junction-to-case
2
DC input current
LIMITS
-0.3 to 6.0
-0.5 to (V
DD
+ 0.5)
-65 to +150
1.5
+175
3.3
UNITS
V
V
°C
W
°C
°C/W
mA
±
10
Notes:
1. Stresses outside the listed absolute maximum ratings may cause permanent damage to the device. This is a stress rating only, and functional operation of the
device at these or any other conditions beyond limits indicated in the operational sections of this specification is not recommended. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
2. Test per MIL-STD-883, Method 1012, infinite heat sink.
2
RECOMMENDED OPERATING CONDITIONS
SYMBOL
V
DD
T
C
V
IN
PARAMETER
Positive supply voltage
Case temperature range
DC input voltage
LIMITS
3.0 to 3.6
-55 to +125
0 to V
DD
UNITS
V
°C
V
DC ELECTRICAL CHARACTERISTICS (Pre/Post-Radiation)*
(V
DD
= 3.0V to 3.6V; -55°C < T
C
< +125°C)
SYMBOL
V
IH
V
IL
V
OL1
V
OL2
V
OH1
V
OH2
C
IN 1
PARAMETER
High-level input voltage
Low-level input voltage
Low-level output voltage
Low-level output voltage
High-level output voltage
High-level output voltage
Input capacitance, all inputs
except PE
Input Capacitance PE
C
IO 1
I
IN
Bidirectional I/O capacitance
ƒ
= 1MHz, V
DD
= 3.3V
V
OUT
= 0V
V
IN
= 0V to V
DD
, all pins except PE
V
IN
= V
DD
, PE only
V
O
= 0V to V
DD
V
DD
= 3.6V
OE = 3.6V
V
DD
= 3.6V, V
O
= V
DD
V
DD
= 3.6V, V
O
= 0V
CMOS input levels (I
OUT
= 0), V
IL
=
0.2V
V
DD
, PE = 3.6V, V
IH
= 3.0V
CMOS input levels V
IL
= V
SS
+0.25V
CE = V
DD
- 0.25 V
IH
= V
DD
- 0.25V
-3
I
OL
= 100µA, V
DD
= 3.0V
I
OL
= 1.0mA, V
DD
= 3.0V
I
OH
= -100µA, V
DD
= 3.0V
I
OH
= -1.0mA, V
DD
= 3.0V
ƒ
= 1MHz, V
DD
= 3.3V
V
IN
= 0V
V
DD
-0.15
V
DD
-0.3
15
CONDITION
MINIMUM
0.7V
DD
0.25V
DD
V
SS
+ 0.05
V
SS
+ 0.10
MAXIMUM
UNIT
V
V
V
V
V
V
pF
20
15
pF
µA
µA
µA
Input leakage current
3
35
20
I
OZ
Three-state output leakage
current
-20
I
OS 2,3
I
DD1
(OP)
4
Short-circuit output current
100
-100
mA
mA
Supply current operating
@15.4MHz (65ns product)
50.0
1.0
mA
mA
I
DD2
(SB)
post-rad
Supply current standby
Notes:
* Post-radiation performance guaranteed at 25°C per MIL-STD-883 Method 1019 at 1E6 rad(Si).
1. Measured only for initial qualification, and after process or design changes that could affect input/output capacitance.
2. Supplied as a design limit but not guaranteed or tested.
3. Not more than one output may be shorted at a time for maximum duration of one second.
4. 1.7mA/MHz.
3
READ CYCLE
A combination of PE greater than V
IH
(min), and CE less than
V
IL
(max) defines a read cycle. Read access time is measured
from the latter of device enable, output enable, or valid address
to valid data output.
An address access read is initiated by a change in address inputs
while the chip is enabled with OE asserted and PE deasserted.
Valid data appears on data output, DQ(7:0), after the specified
t
AVQV
is satisfied. Outputs remain active throughout the entire
cycle. As long as device enable and output enable are active, the
address inputs may change at a rate equal to the minimum read
cycle time.
AC CHARACTERISTICS READ CYCLE (Post-Radiation)*
(V
DD
= 3.0V to 3.6V; -55°C < T
C
< +125°C)
SYMBOL
t
AVAV1
t
AVQV
t
AXQX2
t
GLQX2
t
GLQV
t
GHQZ
t
ELQX2
t
ELQV
t
EHQZ
PARAMETER
Read cycle time
Read access time
Output hold time
OE-controlled output enable time
OE-controlled access time
OE-controlled output three-state time
CE-controlled output enable time
CE-controlled access time
CE-controlled output three-state time
The chip enable-controlled access is initiated by CE going active
while OE remains asserted, PE remains deasserted, and the
addresses remain stable for the entire cycle. After the specified
t
ELQV
is satisfied, the eight-bit word addressed by A(14:0)
appears at the data outputs DQ(7:0).
Output enable-controlled access is initiated by OE going active
while CE is asserted, PE is deasserted, and the addresses are
stable. Read access time is t
GLQV
unless t
AVQV
or t
ELQV
have
not been satisfied.
28F256LV-65
MIN
MAX
65
65
0
0
35
35
0
65
35
UNIT
ns
ns
ns
ns
ns
ns
ns
ns
ns
Notes:
* Post-radiation performance guaranteed at 25°C per MIL-STD-883 Method 1019 at 1E6 rads(Si).
1. Functional test.
2. Three-state is defined as a 200mV change from steady-state output voltage.
4
t
AVAV
A(14:0)
CE
t
ELQX
t
ELQV
OE
t
GLQV
DQ(7:0)
t
GLQX
t
AVQV
t
AXQX
t
GHQZ
t
AVQV
t
EHQZ
Figure 2. PROM Read Cycle
RADIATION HARDNESS
The UT28F256LVQL PROM incorporates special design and
layout features which allow operation in high-level radiation
environments. Aeroflex Colorado Springs has developed special
low-temperature processing techniques designed to enhance the
total-dose radiation hardness of both the gate oxide and the field
oxide while maintaining the circuit density and reliability. For
RADIATION HARDNESS DESIGN SPECIFICATIONS
1
Total Dose
Latchup LET Threshold
Memory Cell LET Threshold
Logic SEU Onset LET
SEU Cross Section
transient radiation hardness and latchup immunity, Aeroflex
Colorado Springs builds all radiation-hardened products on
epitaxial wafers using an advanced twin-tub CMOS process. In
addition, Aeroflex Colorado Springs pays special attention to
power and ground distribution during the design phase,
minimizing dose-rate upset caused by rail collapse.
1E6
>110
>100
>40
7.6E-12
2.5E-17
rad(Si)
MeV-cm
2
/mg
MeV-cm
2
/mg
MeV-cm
2
/mg
cm
2
/bit
errors/bit day
Error rate - geosynchronous orbit, Adams 90% worst case environment
Note:
1. The PROM will not latchup during radiation exposure under recommended operating conditions.
The V2 version has been greatly simplified and only requires the following components:LED lamp (30W or more, internal diameter not less than 7cm), reference price less than 3 yuan
LED light ring, 12-p...
Sunglasses, myopia glasses, hyperopia glasses and the like are common, but the glasses I want to introduce today are really unique. They can help you both visually and auditorily. The two loudspeakers...
TQ210 LED driver and test 1. Writing led driver 1.1 Create a directory in the system /home/share/led/[/color][/size][/font][/align][align=left][font=微软雅黑][size=15px][color=rgb(0, 0, 0)]#mkdir –p /home...
Lierda's LSD_MiniStick, PICCOLO mini simulation kitGiven on TI MCU DAY one yearThe core board simulator is divided into two partsXDS100 EmulatorCore board 28027. The phone's camera is not very good. C...
I right-clicked in the resource view and inserted the activex control, but the space registered on the pc was inserted and it cannot be used on the ppc. How can I correctly insert the webbrowser contr...
Most of the houses we live in now are elevator buildings, mainly because it is more convenient to go up and down the stairs! It can also make life more comfortable. It even helps to increase the ad...[Details]
Is electromagnetic radiation from electric vehicles harmful to the human body? Recently, the issue of electromagnetic radiation from electric vehicles has garnered widespread attention. However, pu...[Details]
1 Introduction
In the mid-1960s, American scientist Maas conducted extensive experimental research on the charging process of open-cell batteries and proposed an acceptable charging curve for ...[Details]
With the rapid adoption of smart electric vehicles, automotive chips are evolving from auxiliary control units to the foundation of the entire vehicle's intelligence. Their applications extend from...[Details]
On August 22, according to the Ministry of Industry and Information Technology's official website, my country's first mandatory national standard for the control of hazardous substances in electric...[Details]
Tires are a very important component for cars. They are related to the driving experience of the vehicle. We are almost inseparable from cars in our daily lives. For tires, according to the role of...[Details]
1. Multi-channel DAC technology bottleneck
Currently,
the development of multi-channel DAC technology focuses on two core challenges.
First, industrial applications urgently ...[Details]
A pure sine wave inverter has a good output waveform with very low distortion, and its output waveform is essentially the same as the AC waveform of the mains power grid. In fact, the AC power prov...[Details]
Wearable technology is taking off, with applications evolving rapidly, from smartwatches to fitness trackers and even smart wigs! Bluetooth Smart is at the center of this revolution. This is the se...[Details]
AI distributed rendering architecture improves mobile phone rendering capabilities, and game performance tests can check frame generation indicators in real time
Shanghai, China, Aug...[Details]
Bearing wear is a common equipment problem in the manufacturing industry. In today's world where controlling production costs is advocated, using repair technology to reduce the scrapping and repla...[Details]
EVTank predicts that all-solid-state batteries will achieve small-scale mass production in 2027 and large-scale shipments by 2030. Global solid-state battery shipments will reach 614.1GWh, of which...[Details]
No one expected that after about a day of downtime, four or five thermostats on the control panel would display four 0000s and flash. We knew it was caused by poor contact of the temperature sensin...[Details]
Industrial equipment plays a significant role in improving industrial automation and accelerating production efficiency. Industrial HMIs (Human-Machine Interfaces) serve as a communication platform...[Details]
The power battery is a crucial component for vehicles, determining its lifespan and range. According to national regulations, when the capacity of an electric vehicle's power battery drops below 80...[Details]
MCU
京公网安备 11010802033920号
EEWORLD
