ESD > 2000V per MIL-STD-883, Method 3015; > 200V using
machine model (C = 200pF, R = 0)
Available in SSOP, TSSOP, and TVSOP Packages
Hot insertion capability
Very low power dissipation
DESCRIPTION:
The FST163209 belongs to IDT's family of Bus switches. Bus switch
devices perform the function of connecting or isolating two ports without
providing any inherent current sink or source capability. Thus they
generate little or no noise of their own while providing a low resistance path
for an external driver. These devices connect input and output ports through
an n-channel FET. When the gate-to-source junction of this FET is
adequately forward-biased the device conducts and the resistance be-
tween input and output ports is small. Without adequate bias on the gate-
to-source junction of the FET, the FET is turned off, therefore with no V
CC
applied, the device has hot insertion capability.
The low on-resistance and simplicity of the connection between input and
output ports reduces the delay in this path to close to zero.
The FST163209 operates as an 18-it bus switch or a 9-bit, 4 port bus
exchanger.
FUNCTIONAL BLOCK DIAGRAM
One of Nine Channels
1
A
1
1
B
1
1
A
2
1
B
2
Flow Control
S
0
S
1
S
2
INDUSTRIAL TEMPERATURE RANGE
1
c /-
1999
Integrated Device Technology, Inc.
DSC-3510/-
OCTOBER 1999
IDT74FST163209
18-BIT BUS SWITCH/ 4 PORT BUS EXCHANGER
INDUSTRIAL TEMPERATURE RANGE
PIN CONFIGURATION
S
0
1
A
1
1
A
2
ABSOLUTE MAXIMUM RATINGS
(1)
Symbol
V
TERM(2)
Rating
Terminal Voltage with Respect to GND
Storage Temperature
Maximum Continuous Channel Current
Max.
–0.5 to +7
–65 to +150
128
Unit
V
°C
mA
FST LINK
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
SO48-1
SO48-2
SO48-3
48
47
46
45
44
43
42
41
40
39
38
37
36
35
34
33
32
31
30
29
28
27
26
25
S
1
S
2
1
B
1
T
STG
I
OUT
GND
2
A
1
2
A
2
1
B
2
2
B
1
NOTES:
1. Stresses greater than those listed under ABSOLUTE MAXIMUM
RATINGS may cause permanent damage to the device. This is a
stress rating only and functional operation of the device at these or
any other conditions above those indicated in the operational sections
of this specification is not implied. Exposure to absolute maximum
rating conditions for extended periods may affect reliability.
2. Vcc, Control, and Switch terminals.
2
B
2
V
CC
3
A
1
3
A
2
GND
3
B
1
3
B
2
CAPACITANCE
(1)
Symbol
Parameter
C
IN
Control Input Capacitance
C
I/O
Switch Input/Output
Capacitance
Conditions
(2)
Switch Off
Typ.
6
17
Unit
pF
pF
GND
4
A
1
4
A
2
GND
4
B
1
4
B
2
5
B
1
5
B
2
NOTES:
1. Capacitance is characterized but not tested.
2. T
A
= 25°C, f = 1MHz, V
IN
= 0V, V
OUT
= 0V
5
A
1
PIN DESCRIPTION
Pin Names
A
1
, A
2
B
1
, B
2
S
0
-
2
I/O
I/O
1
Description
Buses
A
1
, A
2,
B
1
, B
2
Control Pins for Mux and Switch Enable Functions
5
A
2
GND
6
A
1
6
A
2
7
A
1
GND
6
B
1
6
B
2
7
B
1
7
B
2
FUNCTION TABLE
(1)
S
2
L
L
L
L
H
H
H
H
S
1
L
L
H
H
L
L
H
H
S
0
L
H
L
H
L
H
L
H
A
1
Z
B
1
B
2
Z
Z
Z
B
1
B
2
A
2
Z
Z
Z
B
1
B
2
Z
B
2
B
1
Function
Disconnect
A
1
to B
1
A
1
to B
2
A
2
to B
1
A
2
to B
2
Disconnect
A
1
to B
1
, A
2
to B
2
A
1
to B
2
, A
2
to B
1
7
A
2
GND
8
A
1
8
A
2
GND
8
B
1
8
B
2
9
A
1
9
A
2
9
B
1
9
B
2
SSOP/ TSSOP/ TVSOP
TOP VIEW
NOTE:
1. H = HIGH Voltage level
L = LOW Voltage Level
Z = High-Impedence
2
IDT74FST163209
18-BIT BUS SWITCH/ 4 PORT BUS EXCHANGER
INDUSTRIAL TEMPERATURE RANGE
DC ELECTRICAL CHARACTERISTICS OVER OPERATING RANGE
Following Conditions Apply Unless Otherwise Specified:
Operating Conditions: T
A
= -40°C to +85°C, V
CC
= 5.0V ±10%
Symbol
V
IH
V
IL
I
IH
I
IL
I
OZH
I
OZL
V
IK
I
OFF
I
CC
Parameter
Control Input HIGH Voltage
Control Input LOW Voltage
Control Input HIGH Current
Control Input LOW Current
Current during
Bus Switch DISCONNECT
Clamp Diode Voltage
Switch Power Off Leakage
Quiescent Power Supply Current
V
CC
= Min., I
IN
= –18mA
V
CC
= 0V, V
IN
or V
O
≤
5.5V
V
CC
= Max., V
IN
= GND or V
CC
V
CC
= Max., V
O
= 0 to 5V
Test Conditions
Guaranteed Logic HIGH for Control Inputs
Guaranteed Logic LOW for Control Inputs
V
CC
= Max.
V
I
= V
CC
V
I
= GND
Min.
2
—
—
—
—
—
—
—
—
Typ.
(1)
—
—
—
—
—
—
–0.7
—
0.1
Max.
—
0.8
±1
±1
±1
±1
–1.2
±1
3
V
µA
µA
FST LINK
Unit
V
V
µA
µA
BUS SWITCH IMPEDANCE OVER OPERATING RANGE
Following Conditions Apply Unless Otherwise Specified:
Operating Conditions: T
A
= -40°C to +85°C, V
CC
= 5.0V ±10%
Symbol
R
ON
Parameter
Switch On Resistance
(2)
Test Conditions
Vcc = Min., V
IN
= 0V
I
ON
= 64mA
Vcc = Min., V
IN
= 0V
I
ON
= 30mA
Vcc = Min., V
IN
= 2.4V
I
ON
= 15mA
Vcc = Max., V
O
= GND
Min.
—
—
—
—
Typ.
(1)
4
4
6
300
Max.
7
7
15
—
Unit
Ω
Ω
Ω
mA
I
OS
Short Circuit Current
(3)
NOTES:
1. Typical values are at Vcc = 5.0V, +25°C ambient.
2. The voltage drop between the indicated ports divided by the current through the switch.
3. Not more than one output should be shorted at one time. Duration of the test should not exceed one second.
3
IDT74FST163209
18-BIT BUS SWITCH/ 4 PORT BUS EXCHANGER
INDUSTRIAL TEMPERATURE RANGE
POWER SUPPLY CHARACTERISTICS
Symbol
∆I
CC
I
CCD
Parameter
Quiescent Power Supply Current
TTL Inputs HIGH
Dynamic Power Supply Current
(4)
Test Conditions
(1)
V
CC
= Max.
V
IN
= 3.4V
(3)
V
CC
= Max.
Outputs Open
Select Pin Toggling
50% Duty Cycle
V
CC
= Max.
Outputs Open
3 Select Pins Toggling
(9 Switches Toggling)
fi = 10MHz
50% Duty Cycle
Min.
—
—
Typ.
(2)
0.5
120
Max.
1.5
160
Unit
mA
µ A/
MHz/
Select
mA
V
IN
= V
CC
V
IN
= GND
I
C
Total Power Supply Current
(6)
V
IN
= V
CC
V
IN
= GND
V
IN
= 3.4
V
IN
= GND
—
3.6
4.8
—
4.4
7.1
NOTES:
1. For conditions shown as Max. or Min., use appropriate value specified under Electrical Characteristics for the applicable device type. T
A
= –40°C to
+85°C
2. Typical values are at V
CC
= 5.0V, +25°C ambient.
3. Per TTL driven input (V
IN
= 3.4V). All other inputs at V
CC
or GND. Switch inputs do not contribute to
∆I
CC.
4. This parameter represents the current required to switch the internal capacitance of the control inputs at the specified frequency.
Switch inputs generate no significant power supply currents as they transition. This parameter is not directly testable, but is derived for use in Total
Power Supply Calculations.
5. C
PD
= I
CCD
/V
CC
C
PD
= Power Dissipation Capacitance
6. I
C
= I
QUIESCENT
+ I
INPUTS
+ I
DYNAMIC
I
C
= I
CC
+
∆I
CC
D
H
N
T
+ I
CCD
(f
i
N)
I
CC
= Quiescent Current
∆I
CC
= Power Supply Current for a TTL High Input (V
IN
= 3.4V)
D
H
= Duty Cycle for TTL Inputs High
N
T
= Number of TTL Inputs at D
H
I
CCD
= Dynamic Current Caused by an Input Transition Pair (HLH or LHL)
f
i
= Control Input Frequency
N = Number of Control Inputs Toggling at f
i
SWITCHING CHARACTERISTICS OVER OPERATING RANGE
Following Conditions Apply Unless Otherwise Specified:
Commercial: T
A
= -40°C to +85°C, V
CC
= 5.0V ± 10%
V
CC
= 5V ± 10%
Symbol
t
PLH
t
PHL
t
BX
t
PZH
t
PZL
t
PHZ
t
PLZ
|Q
CI
|
|Q
DCI
|
Description
(1)
Data Propagation Delay
A to B, B to A
(2)
Switch Multiplex Delay
S to A, B
Switch CONNECT Delay
S to A, B
Switch DISCONNECT Delay
S to A, B
Charge Injection During Switch DISCONNECT,
Sx to xAx or xBx
(3)
Charge Injection During Switch Multiplex,
Sx to xAx or xBx
(3)
Min.
—
1.5
1.5
1.5
—
—
Typ.
—
—
—
—
1.5
0.5
Max.
0.25
6.5
6.5
7
—
—
V
CC
= 4V
Max.
0.25
7
7
7
—
—
Unit
ns
ns
ns
ns
pC
NOTES:
1. See test circuits and waveforms.
2. The bus switch contributes no Propagation Delay other than the RC Delay of the load interacting with the RC of the switch.
3. |Q
CI
| is the charge injection for a single switch DISCONNECT and applies to either single switches or multiplexers.
|Q
DCI
| is the charge injection for a multiplexer as the multiplexed port switches from one path to another. Charge injection is reduced because the
injection from the DISCONNECT of the first path is compensated by the CONNECT of the second path.
4
IDT74FST163209
18-BIT BUS SWITCH/ 4 PORT BUS EXCHANGER
INDUSTRIAL TEMPERATURE RANGE
TEST CIRCUITS AND WAVEFORMS
TEST CIRCUITS FOR ALL OUTPUTS
V
CC
500
Ω
V
IN
Pulse
Generator
D.U.T.
50pF
R
T
PROPAGATION DELAY
7.0V
SAM E PHASE
INPUT TRANSITION
t
PLH
OUTPUT
t
PLH
t
PH L
t
PH L
3V
1.5V
0V
V
OH
1.5V
V
OL
3V
1.5V
0V
V
OUT
500
Ω
C
L
OPPOSITE PHASE
INPUT TRANSITION
SWITCH POSITION
Test
Open Drain
Disable Low
Enable Low
All Other Tests
Open
FCT LINK
SET-UP, HOLD, AND RELEASE TIMES
Switch
DATA
INPUT
t
SU
TIMING
INPUT
ASYNCHRO NOUS
CONTROL
SYNCHRONO US
CONTROL
t
REM
t
H
3V
1.5V
0V
3V
1.5V
0V
3V
1.5V
0V
3V
1.5V
0V
Closed
DEFINITIONS:
C
L
= Load capacitance: includes jig and probe capacitance.
R
T
= Termination resistance: should be equal to Z
OUT
of the Pulse
Generator.
t
SU
t
H
CHARGE INJECTION
V
CC
ENABLE AND DISABLE TIMES
ENABLE
DISABLE
3V
V
O U T(3)
Switch
Out
1 MHz
Signal
Generator
Enable/Select
Switch In
(1)
D.U.T.
(2)
CONTROL
INPUT
t
PZL
OUTPUT
NORMALLY
LOW
SW ITCH
CLOSED
t
PZH
3.5V
1.5V
0.3V
t
PHZ
0.3V
1.5V
0V
t
PLZ
1.5V
0V
3.5V
V
OL
V
OH
Switch In (MU X)
C
L
=
50pF
NOTES:
1. Select is used with multiplexers for measuring IQ
DCI
I during multiplexer
select. During all other tests Enable is used.
2. Used with multiplexers to measure IQ
DCI
I only.
3. Charge Injection =
∆V
OUT
C
L
, with Enable toggling for IQ
CI
I or Select toggling
for IQ
DCI
I.
∆V
OUT
is the change in V
OUT
and is measured with a 10MΩ
probe.
OUTPUT
NORMALLY
HIGH
SW ITCH
OPEN
0V
PULSE WIDTH
LOW -HIGH-LOW
PULS E
t
W
HIGH-LOW -HIGH
PULS E
1.5V
1.5V
NOTES:
1. Diagram shown for input Control Enable-LOW and input Control Disable-
High efficiency and low standby power consumption are two major challenges in today's switching power supply design. Resonant topology or LLC topology is becoming increasingly popular because it ca...[Details]
In public places such as schools, government agencies, factories and mines, as well as public corridors in residential areas, the phenomenon of long-burning lights is very common, which causes a h...[Details]
1. Principle of displacement angle sensor
The angle sensor is used to detect angles. It has a hole in its body that fits the LEGO axle. When connected to the RCX, the angle sensor counts once ...[Details]
0 Introduction
With the development of society, people pay more and more attention to security work. Monitoring products have been used in various fields instead of being used only in importan...[Details]
With the development and widespread application of computer technology, especially in the field of industrial control, computer communication is particularly important. Although serial communication g...[Details]
1. What is temperature?
Heat is a type of molecular motion. The hotter an object is, the faster its molecules move. Absolute zero is defined as the temperature at which all molecular motion ...[Details]
A standard cell
is an electrochemical
cell
used as a voltage reference standard in many electrical standards laboratories
. If properly maintained, standard cells are very stable. The ...[Details]
In today's body control module (BCM) designs, savvy engineers are moving away from electromechanical relays whenever possible. Their next step is to eliminate fuses. But is eliminating fuses a nece...[Details]
Corelink Semiconductor has launched the CL1100-based 5-7W E27 LED lighting driver system solution DB2. This driver module meets the requirements of small size (L×W×H=5.1cm×2.1cm×1.8cm), low standby...[Details]
LED guardrail lights use fluorescent tubes or LEDs as light sources and continuous guardrails as carriers to form an approximately linear guardrail light strip. This article mainly introduces...[Details]
The rectified DC voltage is then converted back to AC using power electronics such as insulated gate bipolar transistors.
The output voltage is switched on and off at a high frequency, control...[Details]
Since the late 1990s, with the demand for higher system efficiency and lower power consumption, the technological update of telecommunications and data communication equipment has promoted the deve...[Details]
At present, a large number of cooling tower fans, speed fans and special fans are in use in petroleum, chemical, pharmaceutical, metallurgical and other enterprises. Some fans have no monitoring in...[Details]
Rated capacity refers to the maximum output power of the UPS (the product of voltage V and current A).
Usually, the UPS power supplies sold on the market are marked with "W" (watt) for smaller...[Details]
The automotive power electronics market has grown rapidly as comfort and active safety features become more common. As traditional mechanical functions shift to electronic applications, the demand ...[Details]
京公网安备 11010802033920号
EEWORLD
