EEWORLDEEWORLDEEWORLD

Part Number

Search

PICOD-400-LS

Description
THUMB/PUSHWHEEL SWITCH-1SWITCHES, CHANGE-OVER, 0.02A, 20VDC, PANEL MOUNT
CategoryMechanical and electronic products    switch   
File Size308KB,2 Pages
ManufacturerTE Connectivity
Websitehttp://www.te.com
Download Datasheet Parametric View All

PICOD-400-LS Overview

THUMB/PUSHWHEEL SWITCH-1SWITCHES, CHANGE-OVER, 0.02A, 20VDC, PANEL MOUNT

PICOD-400-LS Parametric

Parameter NameAttribute value
MakerTE Connectivity
Reach Compliance Codeunknown
ECCN codeEAR99
body width7.62 mm
body height15 mm
Body length or diameter18 mm
Maximum contact current (DC)0.02 A
Contact (DC) maximum rated R load.02A@20VDC
Maximum contact voltage (DC)20 V
Electrical life100000 Cycle(s)
Manufacturer's serial numberPICOD
Installation featuresPANEL MOUNT
Number of positions1
Number of switching segments1
Maximum operating temperature60 °C
Minimum operating temperature-10 °C
surface mountNO
switch functionCHANGE-OVER
Switch typeTHUMB/PUSHWHEEL SWITCH
PICOD Series
Pushwheel Switches, Subminiature, Panel Mount, Dual Button
The PICOD family offers small panel-mounted pushwheel code
switches, ideally suited for high density applications. They are used
for the controlling and programming of frequency synthesizers,
counters and timers, data comparators, security encoders, weighing
machines, etc. The dependable pushbutton action allows narrow
0.3 inch width on panel. Changes to higher or lower settings are
accomplished rapidly by successive operation of the appropriate
buttons. The featherweight PICOD is less than 0.6 inch high, yet
rugged enough for hand-held and portable instruments that may be
subjected to field abuse. Heavy gold plating on wiping contacts
affords low contact resistance for reliable operation over long
periods of service. Easy-to-read characters are viewed through
dust-sealed window. Installation costs are minimized by snap-
together design – no inconvenient hardware.
MATERIAL SPECIFICATIONS:
Fixed Contacts ..................................1 microns AU over Ni over Cu
Moving Contacts................................Gold-clad Ni over copper alloy
PC Board............................................FR4 Glass epoxy
Molded Parts ......................................Noryl-SE1, Black matte finish
Window..............................................Thermoplastic resin
TYPICAL PERFORMANCE CHARACTERISTICS:
Contact Rating ..................................0.4 VA @ 20 VDC max.
Contact Circuit Resistance ................0.15 Ohm max.
Operating Force ................................Approx. 11 oz.
PC Terminal Spacing ........................0.100"
Character Height/Color.......................122" White (.094" for hex codes)
Life Expectancy ................................More than 105 operations
Operating temperature ......................-10° C to + 60° C
PICOD - 131 - AK
Codes
111 = Decimal
131 = BCD
137 = BCD Complement
301 = Hexadecimal
307 = Hexa. Complement
400 = Switch-over
Connections
AK = pcb short
AL = pcb long
LS = solder pin
AL/D = pcb long, interrupted
ALU = pcb long downward
PICOD111AL
See Code Tables on Page J3
ACCESSORIES
Front Mount
Snap Detent
PICOA
PICOADP
PICOBG
PICOP
B5LS
B5L
Description
Wheel
Marks
J
PICOD Series
Spacer, 0.1" wide
Spacer, 0.1" wide, with decimal point
Spacer, 0.3" wide (same size as switch)
End-plate pair
5 pin connector with PC pins for AK types
5 pin connector with wire lug termination for AK types
J7
Catalog 1308390
Issued 9-04
www.tycoelectronics.com
Dimensions are in inches
and millimeters unless otherwise
specified. Values in parentheses
or brackets are metric equivalents.
Dimensions are shown for
reference purposes only.
Specifications subject
to change.
USA: 1-800-522-6752
Canada: 1-905-470-4425
Mexico: 01-800-733-8926
C. America: 52-55-5-729-0425
South America: 55-11-3611-1514
Hong Kong: 852-2735-1628
Japan: 81-44-844-8013
UK: 44-141-810-8967
Digitally controlled power supply using DSP for secondary voltage regulation
[[i] This post was last edited by lrz123 on 2011-10-25 10:48[/i]]...
lrz123 DIY/Open Source Hardware
About the digital tube display problem
I have been using FPGA to make a digital clock these days, using six digital tubes for display. I used a 20M crystal oscillator and divided it to get a 1KHZ signal, and used this signal to scan the bi...
gavin_8724 FPGA/CPLD
Power supply noise
I use lithium batteries to power a microcontroller through a switching step-down power supply to collect data from a vibration sensor. However, the noise from the power supply always affects the data ...
stuwang Power technology
Why are the first four bytes of a physical sector of an SD card or USB flash drive sometimes written as RRaA by the system?
I write an identifier to the physical sector of a USB flash drive through a filter driver I wrote. I write it starting from the first digit, for example "asdd12344". But sometimes for some reason, the...
hyhjjg Embedded System
Who loads the printer driver under WinCE? How to load it?
As the title says, who loads the printer driver under wince? GWES OR DEVICE? How to load it? Automatically load it when the computer is turned on or dynamically load it? Thanks for the answer....
fifthspace Embedded System
Graphic dot matrix LCD display module user manual
[i=s]This post was last edited by paulhyde on 2014-9-15 08:57[/i] Graphic dot matrix LCD display module user manual...
xfh168168 Electronics Design Contest

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1895  2040  2204  1339  833  39  42  45  27  17 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号