After reading so much information , I still don't know how to configure the clock output from FPGA to external SDRAM. Most of them should use one clk for the internal SDRAM controller of FPGA and anot...
[i=s] This post was last edited by dontium on 2015-1-23 13:22 [/i] The F2812 board is ready, and it can be connected normally using the XDSUSB510 emulation. I burned a LED lighting program, and the bu...
How to connect the driver, qt, and dsp based on the embedded linux operating system and burn them into the board? ? Specific steps, thank you all! ! !...
Please advise!!!
As shown in the figure below, when constructing multiple capacitor arrays, the left side is the plates arranged at equal intervals at the same height, and the right side is the common...
Without saying anything more, I'll post the code first, the picture effect, and the attached download project. You can run it in Qt Creator. The version I use is 4.7.0Operation effect:Code/*Set window...
[color=rgb(68,68,68)][backcolor=rgb(238,238,238)] I would like to ask you experts, if the serial port sending function is as follows: send a character to the PC void Send1Char(char sendchar) { while (...
introduction
Since the beginning of the 21st century, the world of information has changed rapidly. Maybe a high-tech product will be released today and a better similar product will be releas...[Details]
introduction
1 The significance of using RTOS on MSP430
It is understandable that it is meaningless to use RTOS on MSP430. Because the hardware resources of MSP430 are limited (for exampl...[Details]
In
circuit design,
current
measurement
is widely used, and the main fields are divided into three categories: in measurement,
the electric meter
is used to measure the curre...[Details]
When the WDP500-2A plane grating monochromator is used to test the emission wavelength of a high-power laser diode at different currents, the matching of the laser diode has the disadvantages of lo...[Details]
As LEDs continue to improve in almost every aspect of performance and cost, LED lighting is being used in an increasingly wide range of applications, among which LED street lights are a focus of in...[Details]
0 Introduction
With the rise and continuous improvement of the solid-state lighting industry, light-emitting diodes (LEDs) have become an alternative lighting technology and are gr...[Details]
introduction
MEMS is a high-tech that has flourished on the basis of integrated circuit production technology and dedicated micro-electromechanical processing methods. Pressure sensors develop...[Details]
D5026A is a driver IC designed by Shanghai Debei Electronics for energy-saving LED display screens. Its design concept is energy-saving and compatible with existing solutions, that is, it can be ...[Details]
This article will introduce a design method for a distributed control system used in a tracking car, which can perform distributed control of motor modules, sensor modules, and lighting control mod...[Details]
introduction
LEDs continue to gain popularity in automotive applications, thanks to their long lifespan and the flexibility they offer for body styling and interior design. Some may be surpris...[Details]
a. Keep the battery clean, wipe off the spilled electrolyte, contaminated dirt and dust in time; keep the poles and terminal clamps clean and in good contact, and apply vaseline or butter to preven...[Details]
HL201A is a special thick film driver integrated circuit with a capacity of less than 75AGTR developed by Xi'an Power Electronics Technology Research Institute. The article explains the pin arrange...[Details]
Energy conservation and environmental protection are the main directions of current automotive technology research, and power batteries are the key to electric vehicle technology. Research on powe...[Details]
1 Introduction
At present, advocating health has become the focus of people's attention, and the emergence of treadmills has become more and more popular. People can exercise at home or in the ...[Details]
The principles to be followed are as follows:
(1) In terms of component layout, related components should be placed as close as possible. For example, clock generators, crystal oscillat...[Details]
FPGA/CPLD
京公网安备 11010802033920号
EEWORLD
