1. Contact factory for improved stabilities or additional product options. Not all options and codes are available at all
frequencies.
2. Unless other stated all values are valid after warm-up time and refer to typical conditions for supply voltage, frequency
control voltage, load, temperature (25°C).
3. Phase noise degrades with increasing output frequency.
4. Subject to technical modification.
5. Contact factory for availability.
For Additional Information, Please Contact
USA:
Europe:
Asia:
Vectron International
267 Lowell Road
Hudson, NH 03051
Tel: 1.888.328.7661
Fax: 1.888.329.8328
Vectron International
Landstrasse, D-74924
Neckarbischofsheim, Germany
Tel: +49 (0) 3328.4784.17
Fax: +49 (0) 3328.4784.30
Vectron International
68 Yin Cheng Road(C), 22nd Floor
One LuJiaZui
Pudong, Shanghai 200120, China
Tel: +86 21 6194 6886
Fax: +86 21 6194 6699
Disclaimer
Vectron International reserves the right to make changes to the product(s) and or information contained herein without notice. No liability is assumed as a result of their use or application.
No rights under any patent accompany the sale of any such product(s) or information.
Recently, I made a monitoring system with VB and called a free modbus.DLL, but the effect was not good. The main reason was that Modbus itself was not perfect and had many problems. Later, I found nMo...
Since the iPad was launched, quite a few people have tried their best to use it to replace their laptops. Obviously, there are two main issues in making the iPad replace the laptop: software (system) ...
I want to use DCO + FLL to get a more stable 5MHz, so I set the registers: void Clock_Initial(void){ WDTCTL = WDTPW + WDTHOLD; P2SEL |= BIT2; P2DIR |= BIT2; // Test SMCLK Output P2.2 P5SEL |= BIT4 + B...
[b]Technical Description[/b]Excerpt 1: MSP430x2xx Family User's Guide Version.SLAU144J page.363The above is the description of the timer comparison function in the datasheet, which means that when the...
Human body information monitoring is an emerging field. People envision developing wireless electroencephalogram (EEG) monitoring equipment to diagnose epilepsy patients. Wearable wireless EEG can ...[Details]
Sensors have made inroads into automotive, medical, industrial and aerospace applications. But you may not see anything changing yet. Growing demands for safety, convenience, entertainment and efficie...[Details]
Introduction: Design of automated test systems
Challenges
To ensure the quality and reliability of products delivered to customers, test managers and engineers use automated test system...[Details]
In the development of high-stability lasers, real-time monitoring of the working state of the laser is an issue that needs to be focused on. This system realizes the high-stability laser temperatur...[Details]
Adding "intelligence" to measurement systems is becoming more common as 8-bit microcontrollers are inexpensive, widely available, and can be programmed using today's common high-level languages, su...[Details]
Abstract: Based on the research of the communication process between the reader and the RFID tag, combined with the EPC C1G2 protocol and ISO/IEC18000.6 protocol, a digital circuit of RFID tag appl...[Details]
1. What is fading?
In terms of scope, fading can be roughly divided into three types: large area fading, small area fading and indoor fading. As shown in Figure 1, large area fading refers t...[Details]
Most
embedded
systems are powered from a 48V backplane. This voltage is typically stepped down to a lower intermediate bus voltage of 24V, 12V, or 5V to power the circuit board racks withi...[Details]
At present, TPMS (tire pressure monitoring system) is mainly divided into two types, one is indirect type and the other is direct type. The direct TPMS system has been affected by its poor alarm ac...[Details]
Abstract: This paper introduces the controller, interface, display principle and driving method of the handheld computer LCD display based on the SA1110 microprocessor. Combined with the HPC projec...[Details]
The growing global interest in green power has added new variables to the design of power supplies and power adapters. Designers must not only traditionally consider the design specifications requi...[Details]
Today, the value of electronic components in cars accounts for 15-20% of the total vehicle. In the future, as more safety electronic devices, fuel consumption and fuel emission control electronic s...[Details]
After being widely adopted in applications such as backlighting of portable products with small and medium-sized screens, light-emitting diodes (LEDs) have entered the field of general lighting in ...[Details]
Analysis of automotive sensor testing requirements
At present, the control system used in automobiles can be functionally divided into three parts: sensor unit, control unit and execution ...[Details]
1 Introduction
The compression (tension) machine is a machine used to test the strength of building materials and certain products. It is divided into two types according to the working mo...[Details]
Industrial Control Electronics
京公网安备 11010802033920号
EEWORLD
