MHO+62FCD-R-FREQ2 datasheet, PDF

MHO+62FCD-R-FREQ2: DescriptionCMOS Output Clock Oscillator, 2.999MHz Min, 50MHz Max; CategoryPassive components oscillator; File Size59KB，1 Pages; ManufacturerMtronPTI; Websitehttp://www.mtronpti.com; Environmental Compliance

Download Datasheet Parametric View All

MHO+62FCD-R-FREQ2 Overview

CMOS Output Clock Oscillator, 2.999MHz Min, 50MHz Max

Parameter Name	Attribute value
Is it Rohs certified?	conform to
Maker	MtronPTI
Reach Compliance Code	unknown
maximum descent time	10 ns
Frequency Adjustment - Mechanical	NO
frequency stability	500%
JESD-609 code	e1
Manufacturer's serial number	MHO
Installation features	THROUGH HOLE MOUNT
Maximum operating frequency	50 MHz
Minimum operating frequency	2.999 MHz
Maximum operating temperature	70 °C
Minimum operating temperature	-20 °C
Oscillator type	CMOS
Output load	10 TTL, 50 PF
physical size	20.8mm x 13.2mm x 5.1mm
longest rise time	10 ns
Maximum supply voltage	5.5 V
Minimum supply voltage	4.5 V
Nominal supply voltage	5 V
surface mount	NO
maximum symmetry	45/55 %
Terminal surface	Tin/Silver/Copper (Sn/Ag/Cu)

MHO+ Series

14 DIP, 5.0 Volt, HCMOS/TTL, Clock Oscillators

Available Symmetry

* Contact factory for availability.

See page 146 for gull wing

configuration.

Pin Connections

1. Symmetry is measured at 1.4 V with TTL load, and at 50% Vdd with HCMOS load.

2. TTL load - See load circuit diagram #1 on page 148. HCMOS load - See load circuit diagram #2 on page 148.

3. Rise/Fall times are measured between 0.5 V and 2.4 V with TTL load, and between 10% Vdd and 90% Vdd with HCMOS load.

119

Power supply requirements for LED applications: [size=3] Recent advances in LED technology have made it possible to produce LEDs that can output a broad spectrum of light, rather than just the traditional red and green derivatives. As a result, the...; qwqwqw2088 Analogue and Mixed Signal

How to achieve higher baud rate communication in MSComm control of VC++6.0: I am writing something that uses the MSComm control in VC++6.0 for communication, but I cannot achieve communication at 230400 or 256000 baud rates. Is there any way to do this? Is MSComm not qualifie...; haozi Embedded System

LM3S811 development board does not run normally after restart: I am a novice in ARM. I found an EK-LM3S811 development board (black cutout version) in the company. I plan to use it to make a timing control relay program for testing. I used the source code in the ...; hcyang1422 Microcontroller MCU

Communication frequency of PLC serial communication module: If a PLC serial communication module is used, the baud rate can reach 19200. I communicate 10Bytes each time, so is the communication frequency simply 19200/8/10=240Hz? I use Siemens CPU312 and the se...; chenyi9258 Embedded System

About the method of drawing serpentine difference lines: [i=s]This post was last edited by chen468859 on 2017-2-27 15:32[/i] Draw a serpentine differential line similar to Figure 1 Figure 1 The first step is to set up the differential pair. I drew a schemat...; chen468859 PCB Design

[Hua Diao Experience] 02 Simple use of Xingkong board: [i=s]This post was last edited by eagler8 on 2022-6-14 05:29[/i]When I woke up in the morning, while watching Wangzai’s father’s video, I accidentally learned that the main control chip of the Xingkon...; eagler8 MicroPython Open Source section

Shortcut: L0 L1 L2 L3 L4 L5 L6 L7 L8 L9 LA LB LC LD LE LF LG LH LI LJ LK LL LM LN LO LP LQ LR LS LT LU LV LW LX LY LZ M0 M1 M2 M3 M4 M5 M6 M7 M8 M9 MA MB MC MD ME MF MG MH MI MJ MK ML MM MN MO MP MQ MR MS MT MU MV MW MX MY MZ N0 N1 N2 N3 N4 N5 N6 N7 N8 NA NB NC ND NE NF NG NH NI NJ NK NL NM NN NO NP NQ NR NS NT NU NV NX NZ O0 O1 O2 O3 OA OB OC OD OE OF OG OH OI OJ OK OL OM ON OP OQ OR OS OT OV OX OY OZ P0 P1 P2 P3 P4 P5 P6 P7 P8 P9 PA PB PC PD PE PF PG PH PI PJ PK PL PM PN PO PP PQ PR PS PT PU PV PW PX PY PZ Q1 Q2 Q3 Q4 Q5 Q6 Q8 Q9 QA QB QC QE QF QG QH QK QL QM QP QR QS QT QV QW QX QY R0 R1 R2 R3 R4 R5 R6 R7 R8 R9 RA RB RC RD RE RF RG RH RI RJ RK RL RM RN RO RP RQ RR RS RT RU RV RW RX RY RZ

Popular Components