EEWORLDEEWORLDEEWORLD

Part Number

Search

2SA1029DRR

Description
Small Signal Bipolar Transistor, 0.1A I(C), 30V V(BR)CEO, 1-Element, PNP, Silicon, TO-92, TO-92(1), 3 PIN
CategoryDiscrete semiconductor    The transistor   
File Size60KB,3 Pages
ManufacturerHitachi (Renesas )
Websitehttp://www.renesas.com/eng/
Download Datasheet Parametric View All

2SA1029DRR Overview

Small Signal Bipolar Transistor, 0.1A I(C), 30V V(BR)CEO, 1-Element, PNP, Silicon, TO-92, TO-92(1), 3 PIN

2SA1029DRR Parametric

Parameter NameAttribute value
Parts packaging codeTO-92
package instructionCYLINDRICAL, O-PBCY-T3
Contacts3
Reach Compliance Codeunknow
ECCN codeEAR99
Maximum collector current (IC)0.1 A
Collector-emitter maximum voltage30 V
ConfigurationSINGLE
Minimum DC current gain (hFE)250
JEDEC-95 codeTO-92
JESD-30 codeO-PBCY-T3
Number of components1
Number of terminals3
Package body materialPLASTIC/EPOXY
Package shapeROUND
Package formCYLINDRICAL
Polarity/channel typePNP
Certification statusNot Qualified
surface mountNO
Terminal formTHROUGH-HOLE
Terminal locationBOTTOM
transistor applicationsAMPLIFIER
Transistor component materialsSILICON
Nominal transition frequency (fT)280 MHz
Base Number Matches1
How do I design a circuit with such input and output?
1. There are signals in and out, and there may be a clk. When in changes from low level to high level, out should output high level immediately. No matter how in pin changes, out should not change. Ho...
littleshrimp FPGA/CPLD
Board burning problem
Every time the program of the board is changed, the board must be powered off, then powered on again, and the program must be burned again before it can run. This is inconvenient. Are there any improv...
lzx_18570633112 DSP and ARM Processors
X-NUCLEO-IKS01A3 driver for Arduino
Well, I participated in an event and was given a board for free, but the prerequisite was to debug and port it to an MCU, so I wrote the Arduino UNO. Then after I got it, I found that ST actually wrot...
jianshan ST Sensors & Low Power Wireless Technology Forum
In this figure, what is the purpose of connecting a resistor in parallel to ground?
As shown in the figure, what are the functions of resistors R2, R3, R4, and R5 in this circuit diagram? Please give me some advice! ! !...
迷途的小书童 Analog electronics
LPC2000 series register addresses
Are the register addresses of the LPC2000 series the same? Thank you!...
chipsos Embedded System
Can F28027 use CCS3.3?
I recently used CCS3.3 to create a new F28027 project. Why does it always remind me of an error? The method of creating a project is the same as 2812. What is the reason for this?...
huangfuzhiqi Microcontroller MCU

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 497  2577  1961  2679  2383  11  52  40  54  48 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号