EEWORLDEEWORLDEEWORLD

Part Number

Search

MRF206-BF

Description
Rotary Switch
CategoryMechanical and electronic products    switch   
File Size1MB,6 Pages
ManufacturerNDK
Websitehttp://www.ndk.com/en/
Download Datasheet Parametric View All

MRF206-BF Overview

Rotary Switch

MRF206-BF Parametric

Parameter NameAttribute value
MakerNDK
Reach Compliance Codecompliant
Manufacturer's serial numberMR
Switch typeROTARY SWITCH
Series MR
Toggles
Half-Inch Diameter Process Sealed Rotaries
Rockers
General
Specifications
Electrical Capacity (Resistive Load)
For MRA:
For MRF or MRK:
250mA @ 125V AC
0.4VA maximum @ 28V AC/DC maximum
(Applicable Range 0.1mA ~ 0.1A @ 20mV ~ 28V)
Note: Find additional explanation of operating range in Supplement section.
Pushbuttons
Programmable Illuminated PB
Other Ratings
Contact Resistance:
Insulation Resistance:
Dielectric Strength:
Mechanical Life:
Electrical Life:
Range of Operating Torque:
Contact Timing:
Indexing:
Keylocks
10 milliohms maximum for MRA; 50 milliohms maximum for MRF & MRK
100 megohms minimum @ 500V DC
1,000V AC minimum for 1 minute minimum for MRA
500V AC minimum for 1 minute minimum for MRF & MRK
30,000 operations minimum
10,000 operations minimum
0.02 ~ 0.07Nm for MRA; 0.005 ~ 0.02Nm for MRF & MRK
Nonshorting (break-before-make)
MRA – self-cleaning, sliding contact; MRF & MRK – self-cleaning, rotary contactor disk
30°
Materials & Finishes
G
Slides
Shaft:
Stopper Plate:
Bushing/Housing:
Movable Contacts:
End Contacts & Terminals:
Common Contacts & Terminals:
Base:
Brass with nickel plating
Steel with zinc plating for MRA & MRK; polyamide cover with stopper for MRF
Zinc alloy with zinc plating
Copper with silver plating for MRA; phosphor bronze with gold plating for MRF & MRK
Brass with silver plating for MRA; phosphor bronze with gold plating for MRF & MRK
Brass with silver plating for MRA; phosphor bronze with gold plating for MRF & MRK
Diallyl phthalate for MRA; fiberglass reinforced polyamide for MRF & MRK
Rotaries
Environmental Data
Tactiles
Operating Temperature Range:
Humidity:
Vibration:
Shock:
Sealing:
Tilt
–10°C through +70°C (+14°F through +158°F)
90 ~ 95% humidity for 96 hours @ 40°C (104°F)
10 ~ 55Hz with peak-to-peak amplitude of 1.5mm traversing the frequency range & returning
in 1 minute; 3 right angled directions for 2 hours
50G (490m/s
2
) acceleration (tested in 3 right angled directions, with 3 shocks in each direction)
MRK model meets IP67 of IEC60529 standards
Installation
Touch
Mounting Torque:
Cap Installation Force:
.686Nm (6.08 lb
in)
19.6 ~ 29.4N (4.41 ~ 6.61 lbf) for MRA & MRK
Processing
Indicators
Soldering Time & Temperature:
Cleaning:
Accessories
Wave Soldering for MRA: See Profile A in Supplement section.
Wave Soldering for MRF & MRK: See Profile B in Supplement section.
Manual Soldering for MRA: See Profile A in Supplement section.
Manual Soldering for MRF & MRK: See Profile B in Supplement section.
Automated cleaning recommended. Stopper plate, as well as washers for MRA & MRK, must be in
place to maintain automated cleaning. See Cleaning specifications in Supplement section.
Standards & Certifications
Supplement
MRA, MRF, & MRK models have not been tested for UL recognition or CSA certification.
These switches are designed for use in a low-voltage, low-current, logic-level circuit.
When used as intended in a logic-level circuit, the results do not produce hazardous energy.
G16
www.nkk.com
I want to buy a heat gun, please recommend one!
As the title says, but don't buy something too expensive. I can't afford it. I just graduated and don't have much spare money. Two or three hundred yuan will do :congratulate:...
MrKingMCU Buy&Sell
How can the same function be compiled with different addresses?
Dear brothers, I use LPC1752 development board, keil 4.21 compilation environment, and found a strange phenomenon when compiling, see the picture:In the exception vector table definition address, I fo...
seanliu8 NXP MCU
When wince four-wire resistive screen is suspended, there is voltage on the X+ pin
As the title says, when it is hung up, I measured that this pin has voltage, and the other three pins are normal. Has anyone encountered such a problem? Please let me know :)...
一行潦草的情诗 Embedded System
How to get the file name when uploading a file to the SD card through the browser form POST method
How to get the file name when uploading a file to the SD card via the browser form POST method? It can be seen that TCP_net in Keil provides the cgi_process_data function, but it does not provide spec...
academic Microcontroller MCU
Does flash have to be erased before writing?
From EEWORLD cooperation group: 499581...
秋水长天 PCB Design
Design of bus IC card based on 89c52
Design of bus IC card circuit diagram based on 89c52, original program, previously collected data, now share with you and hope to make progress together....
clark MCU

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 87  2215  2519  2146  1826  2  45  51  44  37 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号