and active-low push-pull outputs. The reset outputs are
asserted and held when the supply voltage falls below the
factory-programmed threshold voltage, when the /MR pin
is pulled low, or if the watchdog times out. Reset is
asserted for the reset timeout delay after the supply
voltage increases above the rising threshold voltage or
when manual reset input is asserted high.
The MAX823/4/5 features an integrated pull-up resistor on
the /MR pin. An active-low push-pull reset output (/RESET)
and an active-high reset output (RESET) provide flexibility
when interfacing with various microcontrollers, PMICs, or
load switches. The watchdog input can be left
unconnected for applications that do not require watchdog
monitoring.
The MAX823/4/5 consumes a quiescent current of only
3.8µA and is offered in standard SOT23-5 and SC70-5
packages. It is rated for the –40°C to +125°C temperature
range.
Datasheets and support documentation are available on
Micrel’s website at:
www.micrel.com.
Features
•
•
•
•
•
•
•
•
•
•
•
•
•
Precision 1.665V to 4.625V power supply monitor
±0.5% threshold accuracy at T
A
= +25°C
±1.5% threshold accuracy from T
A
= –40°C to +125°C
3.8µA supply current (S,R,T,W,Y,Z options)
4.8µA supply current (L,M options)
Manual reset input (MAX823/5)
140ms (min.) reset timeout period
1.6s (typ.) watchdog timeout period
Active-high and active-low push-pull outputs
Guaranteed reset output valid to V
CC
= 1V
−40°C
to +125°C junction temperature range
5-pin SOT23 and SC70 packages
8x lower watchdog input current than competition
Applications
•
•
•
•
•
•
Computers and controllers
Embedded controllers
Intelligent instruments
Automotive systems
Critical µP monitoring
Portable/battery-powered equipment
Typical Application
Micrel Inc. • 2180 Fortune Drive • San Jose, CA 95131 • USA • tel +1 (408) 944-0800 • fax + 1 (408) 474-1000 •
http://www.micrel.com
February 26, 2015
Revision 2.0
Micrel, Inc.
Table 1. Part Functionality Guide
Function
Active-Low Reset
Active-High Reset
Watchdog Input
Manual Reset Input
MAX823
Yes
No
Yes
Yes
MAX824
Yes
Yes
Yes
No
MAX823/4/5
MAX825
Yes
Yes
No
Yes
Ordering Information
(1)
Top Marking
Option
Suffix
Reset
Threshold
MAX823
EUK
(SOT23-5)
X3L
X3M
X3T
X3S
X3R
X3Z
X3Y
X3W
(2)
MAX824
(2)
MAX825
(2)
Temp. Range
(2)
EXK
(SC70-5)
XA
XB
XC
XE
XF
XJ
XK
XL
EUK
(SOT23-5)
X4L
X4M
X4T
X4S
X4R
X4Z
X4Y
X4W
(2)
EXK
(SC70-5)
4Y
YA
YB
YC
YD
YE
YF
YG
EUK
(SOT23-5)
X5L
X5M
X5T
X5S
X5R
X5Z
X5Y
X5W
(2)
EXK
(SC70-5)
YH
YI
YJ
YK
YO
YR
YS
YT
–40°C to +125°C
–40°C to +125°C
–40°C to +125°C
–40°C to +125°C
–40°C to +125°C
–40°C to +125°C
–40°C to +125°C
–40°C to +125°C
Lead
Finish
L
M
T
S
R
Z
Y
W
Note:
4.625V
4.375V
3.075V
2.925V
2.625V
2.315V
2.188V
1.665V
Pb-Free
Pb-Free
Pb-Free
Pb-Free
Pb-Free
Pb-Free
Pb-Free
Pb-Free
1. Insert the desired option suffix (based on the desired reset threshold) into the blank to complete the part number. All reset options are available in
both SOT23 and SC70 Pb-Free packages. Standard ship format is in tape and reel only. There is a 3,000 piece minimum order increment for
production reel. Reel diameter is 7 inches, hub diameter is 2 inches, and width is 8mm.
2. -5 indicates a 5-pin package.
Part Number Convention
February 26, 2015
2
Revision 2.0
Micrel, Inc.
MAX823/4/5
Pin Configuration
MAX823
SOT23(EUK) & SC70(EXK)
Top View
MAX824
SOT23(EUK) & SC70(EXK)
Top View
MAX825
SOT23(EUK) & SC70(EXK)
Top View
Pin Description
Pin Number
MAX823
Pin Number
MAX824
Pin Number
MAX825
Pin Name
Pin Function
Active-Low Reset Output. Pulses low for 200ms when triggered, and
remains low whenever V
CC
is below the reset threshold or when /MR is
a logic low. It remains low for 200ms after one of the following occurs:
V
CC
rises above the reset threshold, the watchdog triggers a reset, or
/MR goes low to high.
Ground.
Active-High Reset Output. Pulses high for 200ms when triggered, and
remains high whenever V
CC
is below the reset threshold or when /MR
is a logic low. It remains high for 200ms after one of the following
occurs: V
CC
rises above the reset threshold, the watchdog triggers a
reset, or /MR goes low to high. RESET is the inverse of /RESET.
Watchdog Input. If WDI remains either high or low for longer than the
watchdog timeout period, the internal watchdog timer runs out and a
reset is triggered. The internal watchdog timer clears whenever reset
is asserted, or whenever WDI sees a rising or falling edge. If WDI is
left unconnected or is connected to a three-stated buffer output, the
watchdog feature is disabled.
Manual Reset Input. A logic low on /MR asserts reset. Reset remains
asserted as long as /MR is held low and for 200ms after /MR returns
high. The active-low input has an internal 52kΩ pull-up resistor. It can
be driven from a CMOS logic line or shorted to ground with a switch.
Leave open or connect to VCC if unused.
Supply Voltage Pin. VCC is the input to the supply voltage monitor.
When the supply voltage falls below the reset threshold voltage, reset
outputs (/RESET and RESET) are triggered immediately. When the
supply voltage rises above the reset threshold plus hysteresis voltage,
the reset outputs remain asserted for the duration of the reset timeout
period. An optional 0.1µF bypass capacitor mounted close to VCC
provides additional transient immunity.
1
1
1
/RESET
2
2
2
GND
-
3
3
RESET
4
4
-
WDI
3
-
4
/MR
5
5
5
VCC
February 26, 2015
3
Revision 2.0
Micrel, Inc.
MAX823/4/5
Absolute Maximum Ratings
(3)
Supply Voltage (V
CC
) ....................................
−0.3V
to
+6.0V
/MR, WDI, RESET, /RESET..................
−0.3V
to V
CC
+0.3V
Input Current (All Pins except RESET, /RESET) ........ 20mA
Output Current (RESET, /RESET) .............................. 20mA
Junction Temperature (T
J
) ........................
−40°C
to +150°C
Storage Temperature (Ts).........................
−65°C
to +150°C
(5)
ESD Rating (Human Body Model)(MAX823/4/5) ........ 3kV
Operating Ratings
(4)
Supply Voltage (V
CC
) .................................... +1.0V to +5.5V
Watchdog Input (WDI)........................................... 0V to V
Telemetry and remote control system is an indispensable and important technical means in China's national defense construction and national economic construction. It is mainly used for long-distance t...
IIS3DHHCTR is a popular accelerometer in SensorTile.box
Unfortunately, there is no code to test it in the official firmware.
Because there is no 1.8V emulator, I just built a project "with my eyes clo...
littleshrimpST Sensors & Low Power Wireless Technology Forum
[size=4] I have been working on emWIN recently, using ST's 429. I have made several interfaces and the control of the touch screen is basically fine. Now I am going to use external buttons to implemen...
After generating a driver using DriverWized of DS3.2, the generated win32 console application cannot open and run the .exe file. Error message: Could not execute: Bad executable format (Win32 error 19...
[font=微软雅黑][size=5]For MSP430, some chips have library functions. Do you prefer to continue to use registers for development or use new libraries for development, or use both? [/size][/font][font=微软雅黑...
Designing for automotive LCD displays larger than 5" can be complex. The display source driver requires a supply rail called analog voltage device drain (AVDD) in the 10V to 15V range and two supply ...[Details]
In order to strengthen the management of new energy vehicle charging facilities in our city, prevent and reduce accidents, protect the lives and property of the people, and improve the public safet...[Details]
1. Test conditions Hardware: STM32L432KC Main frequency: 80MHz Compiler: IAR 8.20.1 Compiler options: High Speed no size constraints CRC generator polynomial: 0x782f 2. Test Method The softwar...[Details]
1. About FPU transplantation As long as the chip has FPU function, the use of FPU is generally enabled by default. You can also select it in the Options tab; 2. About the transplantation of DSP li...[Details]
I used STM32CubeMX V4.22.1 to generate a project including EHT and Lwip. The debugging has been abnormal. After careful inspection, the following problems were found: 1. The hardware uses LAN8720A, b...[Details]
There has been a lot of news about Huawei
phones
recently
. At the
Huawei
Global Analyst Conference
on the 17th
,
Huawei
announced that it will launch
5G
phones
in the seco...[Details]
The application of millimeter wave technology in mobile communications also involves a series of technical problems, including the large propagation loss of millimeter waves and the susceptibility ...[Details]
Why does MCU have a watchdog? With this question, let's learn about watchdogs. Even the 51 single-chip microcomputer has a watchdog, which shows that this dog has a special meaning to us. The purpose...[Details]
LiDAR: Autonomous driving from the perspective of optoelectronic technology LiDAR and competing sensor technologies (camera, radar, and ultrasonic) intensify the need for sensor fusion and the need...[Details]
ADI has established long-term good relationships with car manufacturers and Tier 1 component suppliers. Based on its previous long-term successful cooperation with new energy vehicles and suppliers a...[Details]
As shown in the figure, the author soldered a STM32F207VET6 board using a TQFP (32-100PIN) 0.55MM to direct plug adapter board. The board leads out the SWD debug interface (only PA13 and PA14 are occ...[Details]
The storage media corresponding to the three boot modes of STM32 are built-in to the chip, they are: 1. User Flash = Flash built into the chip 2.SRAM = RAM area built into the chip, which is the m...[Details]
1) ADC multi-channel acquisition: (Multi-channel acquisition must use scanning mode. In scanning mode, the channels of the rule group share a register, so DMA transmission must be used; to prevent da...[Details]
Note: This STM32 microcontroller is the STM32F103 series. The ADC of Stm32 has DMA function. This is beyond doubt and is what we use most! However, if we want to sample a signal (such as a pulse sign...[Details]
When the program starts running, light A turns on for 5 seconds, then turns off, light B turns on for 5 seconds, light B turns off, light C turns on for 5 seconds, light C turns off, the program ends...[Details]
Test/Measurement
京公网安备 11010802033920号
EEWORLD
