DM74H53N datasheet, PDF - EEWORLD Datasheet

DM74H53N: DescriptionIC,LOGIC GATE,2/2/2/3IN AND-NOR,H-TTL,DIP,14PIN,PLASTIC; Categorylogic logic; File Size91KB，2 Pages; ManufacturerNational Semiconductor（TI ）; Websitehttp://www.ti.com

Stay tuned Parametric

DM74H53N Overview

IC,LOGIC GATE,2/2/2/3IN AND-NOR,H-TTL,DIP,14PIN,PLASTIC

Parameter Name	Attribute value
Is it Rohs certified?	incompatible
Maker	National Semiconductor（TI ）
Reach Compliance Code	compliant
JESD-30 code	R-PDIP-T14
JESD-609 code	e0
Logic integrated circuit type	AND-OR-INVERT GATE
MaximumI(ol)	0.02 A
Number of terminals	14
Maximum operating temperature	70 °C
Minimum operating temperature
Package body material	PLASTIC/EPOXY
encapsulated code	DIP
Encapsulate equivalent code	DIP14,.3
Package shape	RECTANGULAR
Package form	IN-LINE
Prop。Delay @ Nom-Sup	11 ns
Certification status	Not Qualified
Schmitt trigger	NO
surface mount	NO
technology	TTL
Temperature level	COMMERCIAL
Terminal surface	Tin/Lead (Sn/Pb)
Terminal form	THROUGH-HOLE
Terminal pitch	2.54 mm
Terminal location	DUAL

PTC Thermistor Terminology: [size=4]Resistance-temperature characteristics: [/size] [size=4]Refers to the relationship between the zero-power resistance value of a PTC thermistor and the temperature of the resistor body under a ...; fish001 Analogue and Mixed Signal

MSP430 MCU Simulation Example 19-D/A Conversion Sine Wave Generator Based on Proteus: 1. Task RequirementsUse the MSP30F247 microcontroller as a controller to achieve a sine wave signal output with a maximum value of +/- 5V and a frequency of 50Hz. 2. Hardware circuitThe hardware circu...; 火辣西米秀 Microcontroller MCU

I don't understand a section of ARM assembly code, please give me some advice.: IMPORT |Image$$RO$$Limit| IMPORT |Image$$RW$$Base| IMPORT |Image$$ZI$$Base| IMPORT |Image$$ZI$$Limit| When writing C code on the development board, the ARM assembler must be initialized before the C c...; ldfree ARM Technology

About the latch pin of the NADV connection latch of stm32f103VE: I saw the truth table of a general latch like this, and my NADV is connected to the C pin.Then I saw the timing diagram of the multiplexing mode of FSMCI would like to ask, if I connect it like this, ...; chonchie stm32/stm8

Why should small capacitors be placed close to the circuit when decoupling the power supply?: When decoupling the power supply, it is usually achieved by using a small capacitor and a large capacitor. But why must the small capacitor be as close to the circuit as possible and the wiring as sho...; Grizabella Analog electronics

Max32630 (III) - OLED screen display time: [i=s]This post was last edited by 29447945 on 2017-9-13 18:57[/i] An OLED display screen has been adjusted for a long time, and it can finally display today. I have two screens, one for SPI communicat...; 29447945 DIY/Open Source Hardware

Shortcut: L0 L1 L2 L3 L4 L5 L6 L7 L8 L9 LA LB LC LD LE LF LG LH LI LJ LK LL LM LN LO LP LQ LR LS LT LU LV LW LX LY LZ M0 M1 M2 M3 M4 M5 M6 M7 M8 M9 MA MB MC MD ME MF MG MH MI MJ MK ML MM MN MO MP MQ MR MS MT MU MV MW MX MY MZ N0 N1 N2 N3 N4 N5 N6 N7 N8 NA NB NC ND NE NF NG NH NI NJ NK NL NM NN NO NP NQ NR NS NT NU NV NX NZ O0 O1 O2 O3 OA OB OC OD OE OF OG OH OI OJ OK OL OM ON OP OQ OR OS OT OV OX OY OZ P0 P1 P2 P3 P4 P5 P6 P7 P8 P9 PA PB PC PD PE PF PG PH PI PJ PK PL PM PN PO PP PQ PR PS PT PU PV PW PX PY PZ Q1 Q2 Q3 Q4 Q5 Q6 Q8 Q9 QA QB QC QE QF QG QH QK QL QM QP QR QS QT QV QW QX QY R0 R1 R2 R3 R4 R5 R6 R7 R8 R9 RA RB RC RD RE RF RG RH RI RJ RK RL RM RN RO RP RQ RR RS RT RU RV RW RX RY RZ

Popular Components