EEWORLDEEWORLDEEWORLD

Part Number

Search

PH1-FI2FC4362

Description
Transponder, 10660Mbps(Tx), 10660Mbps(Rx), FC/UPC Connector,
CategoryWireless rf/communication    Optical fiber   
File Size240KB,6 Pages
ManufacturerLumentum Operations LLC
Download Datasheet Parametric View All

PH1-FI2FC4362 Overview

Transponder, 10660Mbps(Tx), 10660Mbps(Rx), FC/UPC Connector,

PH1-FI2FC4362 Parametric

Parameter NameAttribute value
MakerLumentum Operations LLC
Reach Compliance Codecompliant
Other featuresIT ALSO OPERATE FROM 1280NM TO 1600NM
body height13.2 mm
Body length or diameter84.1 mm
Communication standardsGR-253
Connection TypeFC/UPC CONNECTOR
Data rate (receive)10660 Mbps
Data rate (send)10660 Mbps
Fiber optic equipment typesTRANSCEIVER, TRANSPONDER
Nominal operating wavelength1564 nm
Nominal optical power output1.122 mW
minimum return loss-27 dB
COMMUNICATIONS MODULES & SUBSYSTEMS
10 Gb/s TDM/DWDM 300 Pin SFF MSA SR2/IR2/LR2 Transponder
PH1 Series
Key Features
• Three configurations supporting SR2/IR2/LR2 applications
• Supports dense wavelength division multiplexing
(DWDM) applications (without wavelocker)
• Microprocessor controls to support I2C
• Integrated 16:1/1:16 mux/demux
• Small form factor package (2.2" x 3.0" x 0.53") for high
density applications
• Low power consumption: 4.8 W typical, 6.8 W maximum
for TDM applications
• 70 °C maximum operating temperature
• High sensitivity PIN or APD receivers
• SONET, FEC, Ethernet and Multirate Capable Versions
• Forward, counter and line timing clocking modes
Applications
Telecommunications
Metropolitan Area Networks
Subscriber loop
Intra-office SONET/SDH
High bit-rate data communications
JDSU 10 Gb/s PH1 Series transponders are intended for 1550 nm system
applications with reaches of up to 80 km. The series includes three different
transponders for SR2 (25 km), IR2 (40 km), and LR2 (80 km) TDM or DWDM
applications. Each transponder accepts 16 bits of parallel digital data and converts
it to a 10 Gb/s NRZ modulated optical signal. It also accepts a 10 Gb/s NRZ
modulated optical signal and converts it into 16 bit wide parallel digital data.
The PH1 series offers low DC power dissipation and is available in either a small
form factor package (2.2 x 3 x 0.53 inches) or in a larger footprint (3.5 x 4.5 x 0.53
inches) package, depending on system thermal performance requirements. The
transmit design uses an Electro-Absorptive Modulated Laser (EML) which,
depending on the configuration, produces an average output power of between
-4 dBm to 2 dBm (EOL). A PIN (-17 dBm typical sensitivity) or APD (-24 dBm
typical sensitivity) receiver is available, based on system configurations.
JDSU PH1 Series transponders are designed to support the following data rates:
9.953 Gb/s (SONET), 10.3125 Gb/s (Ethernet), 10.664 Gb/s (FEC Encoded),
10.709 Gb/s FEC, or 11.09 Gb/s EFEC. They meet all applicable SONET/SDH standards.
Compliance
• Telcordia GR-253-Core
NORTH AMERICA
:
800 498-JDSU (5378)
WORLDWIDE
:
+800 5378-JDSU
WEBSITE
:
www.jdsu.com
Design of dot matrix driver for Arduino platform
Hardware Platform: 1. Cookie board officially launched by CooCox. This board is based on 32-bit ARM Cortex M0/3/4 MCU, fully compatible with Arduino, and has richer interface functions. 2. 8*8 dot mat...
mcy_cool MCU
LM4F231 float variable problem under IAR
The chip used is LM4F231, and the integrated development environment is IAR 6.3. 1: When a float variable is defined as a local variable, the variable valueAnd the variable address is not assigned. Ho...
yjf256156 Microcontroller MCU
Power supply circuit tips
[Transfer] Sharing the key points of power supply circuit Author: [color=#3e3e3e]rainysky[/color][font=Helvetica Neue, Helvetica, Hiragino Sans GB, Microsoft YaHei, Arial, sans-serif][color=#3e3e3e][s...
木犯001号 Power technology
Flash development under Wince
I found the source code of a flash player, flash5, and ported it to run on the wince6 platform. There are images, but no sound. Is there any hero who has the flash source code under wince that can pla...
dsx_msp430 Embedded System
Just want to ask~~~
I wonder if ST has plans to make an STM32 with an Ethernet port + external bus? Haha Pleasesend me some news~~~, if not, I will turn to Ti, haha...
yellowcrab stm32/stm8
About the impedance matching of ultrasound
My recent project is about ultrasonic Doppler flowmeter. There is an impedance matching problem about the ultrasonic transmitting circuit. I wonder if there are any experts who know the answer. Please...
tuxiaoli20 Analog electronics

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2620  1387  2492  2129  2117  53  28  51  43  16 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号