REVISIONS
LTR
A
DESCRIPTION
Page 2, 1.3: Change
θ
JA
. Page 6, 4.2a(2) and 4.3.2b(2): Change T
A
to T
C
for burn-in and life test. Pages 7 and 8, table I: Add end-point
electricals for V
TH
. Add footnote 2/.
Made technical changes to table I. Updated drawing format with
editorial changes. Added device types 02 through 07. Added cases
Y,Z, U, and T. Changed to reflect MIL-H-38534 processing. Device
type 01 inactive for new design. Added current CAGE code 67268 to
sheet 1.
Add device type 08. Made technical changes to table I. Change
dimensions for case outline Y. Change dimensions for case outline U.
Editorial changes throughout.
Changes in accordance with NOR 5962-R170-95.
Update drawing boilerplate to most current format.
Rewrite paragraphs 4.2.a.2. and 4.3.3.b.2 to add T
C
.
Table I, Total current, I
CC1
-SB, I
CC1
-25, I
CC1
-50, I
CC1
-100 for device
type 06; change the maximum limit from 30 mA to 60 mA. (4 places) -
gz
Added device type 09. Updated boilerplate paragraphs. -sld
Updated drawing paragraphs. -sld
Figure 2; Corrected terminal symbols for pins 15 and 16 from "RX
Data out and RX Data out" to "RX Data in and RX Data in". -sld
DATE (YR-MO-DA)
86-10-30
APPROVED
W. Heckman
B
90-02-09
W. Heckman
C
94-01-14
K. Cottongim
D
E
F
G
95-07-12
02-02-25
04-12-02
07-05-10
Kendall A. Cottongim
Raymond Monnin
Raymond Monnin
Robert M. Heber
H
J
K
10-01-15
11-09-01
13-01-30
Charles F. Saffle
Charles F. Saffle
Charles F. Saffle
THE ORIGINAL FIRST SHEET OF THIS DRAWING HAS BEEN REPLACED
CURRENT CAGE CODE 67268
REV
SHEET
REV
SHEET
REV STATUS
OF SHEETS
PMIC N/A
K
15
K
16
K
17
K
18
REV
SHEET
PREPARED BY
K
19
K
20
K
21
K
1
K
2
K
3
K
4
K
5
K
6
K
7
K
8
K
9
K
10
K
11
K
12
K
13
K
14
Donald R. Osborne
STANDARD
MICROCIRCUIT
DRAWING
THIS DRAWING IS AVAILABLE
FOR USE BY ALL
DEPARTMENTS
AND AGENCIES OF THE
DEPARTMENT OF DEFENSE
CHECKED BY
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
http://www.landandmaritime.dla.mil/
D. A. DiCenzo
APPROVED BY
N. A. Hauck
DRAWING APPROVAL DATE
MICROCIRCUIT, HYBRID, DIGITAL, SINGLE
CHANNEL, DRIVER-RECEIVER
SIZE
CAGE CODE
86-07-30
AMSC N/A
REVISION LEVEL
K
A
14933
SHEET
1 OF
5962-86049
21
5962-E208-13
DSCC FORM 2233
APR 97
1. SCOPE
1.1 Scope. This drawing describes device requirements for class H hybrid microcircuits to be processed in accordance with
MIL-PRF-38534 and a choice of case outlines and lead finishes are available and are reflected in the Part or Identifying
Number (PIN).
1.2 PIN. The PIN shall be as shown in the following example:
5962-86049
Drawing number
01
Device type
(see 1.2.1)
X
Case outline
(see 1.2.2)
A
Lead finish
(see 1.2.3)
1.2.1 Device type(s). The device type(s) shall identify the circuit function as follows:
Device type
01
02
03 1/
04 1/
05
06
07
08
09
Generic number
BUS-63105
BUS-63105II, BUS-63106II
ARX2402
ARX3402
CT-1487M, BUS-8553, BUS-63100
NHI-1509
FC155361
FC155362
ACT4402
Circuit function
Single channel driver-receiver
Low power, single channel driver-receiver
Single channel driver-receiver
Low power, single channel driver-receiver
Single channel driver-receiver
Single channel driver-receiver
Single channel driver-receiver
Single channel driver-receiver
Low power, single channel driver-receiver
1.2.2 Case outline(s). The case outline(s) shall be as designated in MIL-STD-1835 and as follows:
Outline letter
T
U
X
Y
Z
Descriptive designator
See figure 1
See figure 1
See figure 1
See figure 1
See figure 1
Terminals
24
24
24
24
24
Package style
Flat package
Dual-in-line package
Dual-in-line package
Dual-in-line package
Dual-in-line package
1.2.3 Lead finish. The lead finish shall be as specified in MIL-PRF-38534.
1/
The device types 03 and 04 are no longer available. Device type 09 may be evaluated as a possible substitute.
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
SIZE
A
REVISION LEVEL
K
5962-86049
SHEET
2
DSCC FORM 2234
APR 97
1.3 Absolute maximum ratings. 1/
Supply voltage range:
V
CC
(device types 01, 03, 04, 05, 06, 07, 08, and 09) ..............
V
EE
(device types 01, 02, 03, 04, 05, 07, 08, and 09) ..............
V
CC1
.........................................................................................
Logic input voltage range ..........................................................
Receiver differential voltage .....................................................
Receiver common mode voltage range .....................................
Driver peak output current .........................................................
Power dissipation (P
D
) at +125°C:
Device types 01, 05, 07, and 08 .............................................
Device types 02 and 09 ..........................................................
Device type 03 .......................................................................
Device type 04 ........................................................................
Device type 06 .......................................................................
Storage temperature range ........................................................
Lead temperature (soldering, 10 seconds) ................................
Junction temperature (T
J
) .........................................................
Thermal resistance, junction-to-case (θ
JC
):
Device types 01, 06, 07, and 08 .............................................
Device types 02 and 09 ..........................................................
Device type 03 .......................................................................
Device type 04 ........................................................................
Device type 05 ........................................................................
Thermal resistance, junction to ambient (θ
JA
):
Device types 01, 06, 07, 08, and 09 .......................................
Device type 02 .........................................................................
Device type 03 .......................................................................
Device type 04 ........................................................................
Device type 05 ........................................................................
1.4 Recommended operating conditions.
Supply voltage range:
V
CC
(device types 01, 03, 04, 05, 06, 07, 08, and 09) ..............
V
EE
(device types 01, 02, 03, 04, 05, 07, 08, and 09) ..............
V
CC1
.........................................................................................
Logic input voltage range ..........................................................
Receiver differential voltage ......................................................
Receiver common mode voltage range .....................................
Driver peak output current:
Device types 01, 03, 04, 05, 06, 07, and 08 ...........................
Device type 02 .........................................................................
Serial data rate .........................................................................
Junction temperature (T
J
) .........................................................
Case operating temperature range (T
C
) ...................................
-0.3 V dc to +18 V dc
+0.3 V dc to -18 V dc
-0.3 V dc to +7 V dc
-0.3 V dc to V
CC1
40 Vp-p
-10 V dc to +10 V dc
200 mA
4W
2.5 W
2.2 W
1.6 W
0.585 W
-65°C to +150°C
+300°C
+160°C
8.8°C/W
7.0°C/W
47.2°C/W
88°C/W
60°C/W
38.8°C/W
37.0°C/W
77.2°C/W
110°C/W
80°C/W
+14.25 V dc to +15.75 V dc
-14.25 V dc to -15.75 V dc
+4.5 V dc to +5.5 V dc
0 V dc to +5.0 V dc
30 Vp-p
-5.0 V dc to +5.0 V dc
180 mA
160 mA
1.0 MHz maximum
+150°C maximum
-55°C to +125°C
1/
Stresses above the absolute maximum rating may cause permanent damage to the device. Extended operation at the
maximum levels may degrade performance and affect reliability.
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
SIZE
A
REVISION LEVEL
K
5962-86049
SHEET
3
DSCC FORM 2234
APR 97
2. APPLICABLE DOCUMENTS
2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part
of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the
solicitation or contract.
DEPARTMENT OF DEFENSE SPECIFICATION
MIL-PRF-38534 - Hybrid Microcircuits, General Specification for.
DEPARTMENT OF DEFENSE STANDARDS
MIL-STD-883 - Test Method Standard Microcircuits.
MIL-STD-1835 - Interface Standard for Electronic Component Case Outlines.
DEPARTMENT OF DEFENSE HANDBOOKS
MIL-HDBK-103 - List of Standard Microcircuit Drawings.
MIL-HDBK-780 - Standard Microcircuit Drawings.
(Copies of these documents are available online at
https://assist.dla.mil/quicksearch/
or from the Standardization Document
Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.)
2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text
of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a
specific exemption has been obtained.
3. REQUIREMENTS
3.1 Item requirements. The individual item performance requirements for device class H shall be in accordance with MIL-
PRF-38534. Compliance with MIL-PRF-38534 may include the performance of all tests herein or as designated in the device
manufacturer's Quality Management (QM) plan or as designated for the applicable device class. The manufacturer may
eliminate, modify or optimize the tests and inspections herein, however the performance requirements as defined in MIL-PRF-
38534 shall be met for the applicable device class. In addition, the modification in the QM plan shall not affect the form, fit, or
function of the device for the applicable device class.
3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified
in MIL-PRF-38534 and herein.
3.2.1 Case outline(s). The case outline(s) shall be in accordance with 1.2.2 herein and figure 1.
3.2.2 Terminal connections. The terminal connections shall be as specified on figure 2.
3.2.3 Waveforms. The waveforms shall be as specified on figure 3.
3.3 Electrical performance characteristics. Unless otherwise specified herein, the electrical performance characteristics are
as specified in table I and shall apply over the full specified operating temperature range.
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
SIZE
A
REVISION LEVEL
K
5962-86049
SHEET
4
DSCC FORM 2234
APR 97
3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical
tests for each subgroup are defined in table I.
3.5 Marking of device(s). Marking of device(s) shall be in accordance with MIL-PRF-38534. The device shall be marked with
the PIN listed in 1.2 herein. In addition, the manufacturer's vendor similar PIN may also be marked.
3.6 Data. In addition to the general performance requirements of MIL-PRF-38534, the manufacturer of the device described
herein shall maintain the electrical test data (variables format) from the initial quality conformance inspection group A lot sample,
for each device type listed herein. Also, the data should include a summary of all parameters manually tested, and for those
which, if any, are guaranteed. This data shall be maintained under document revision level control by the manufacturer and be
made available to the preparing activity (DLA Land and Maritime -VA) upon request.
3.7 Certificate of compliance. A certificate of compliance shall be required from a manufacturer in order to supply to this
drawing. The certificate of compliance (original copy) submitted to DLA Land and Maritime -VA shall affirm that the
manufacturer's product meets the performance requirements of MIL-PRF-38534 and herein.
3.8 Certificate of conformance. A certificate of conformance as required in MIL-PRF-38534 shall be provided with each lot of
microcircuits delivered to this drawing.
4. VERIFICATION
4.1 Sampling and inspection. Sampling and inspection procedures shall be in accordance with MIL-PRF-38534 or as
modified in the device manufacturer's Quality Management (QM) plan. The modification in the QM plan shall not affect the form,
fit, or function as described herein.
4.2 Screening. Screening shall be in accordance with MIL-PRF-38534. The following additional criteria shall apply:
a.
Burn-in test, method 1015 of MIL-STD-883.
(1)
Test condition A, B, C, or D. The test circuit shall be maintained by the manufacturer under document revision level
control and shall be made available to either DLA Land and Maritime -VA or the acquiring activity upon request.
Also, the test circuit shall specify the inputs, outputs, biases, and power dissipation, as applicable, in accordance
with the intent specified in method 1015 of MIL-STD-883.
T
A
or T
C
as specified in accordance with table I of method 1015 of MIL-STD-883.
(2)
b.
Interim and final electrical test parameters shall be as specified in table II herein, except interim electrical parameter
tests prior to burn-in are optional at the discretion of the manufacturer.
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
SIZE
A
REVISION LEVEL
K
5962-86049
SHEET
5
DSCC FORM 2234
APR 97
Power technology
京公网安备 11010802033920号
EEWORLD
