6001 Series Delay On Operate Digital Timing Module
Fixed Timing, Solid State Output
Product Facts
■
■
■
■
■
Fixed delay on operate timer
300mA output
CMOS digital design
Voltage surge protection
Qualified to MIL-R-83726/13
Electrical Specifications
Timing Range:
50 ms to 600 s.
Timing Accuracy:
±10% of nominal
timing under all conditions of input
voltage and environmental extremes.
Recycle Characteristics:
Before Time Out:
A power interruption
occuring after the start but before
completion of the timing cycle shall be
for a duration of 0.5% of the nominal
time delay or 10ms, whichever is
greater, to ensure a loss in timing of no
greater than 10%.
After Time Out:
A power interruption
of 0.5% of the nominal time delay or
10ms, whichever is greater, will initiate a
new timing cycle with a loss in timing of
no greater than 5%.
Input Data:
Input Voltage:
28Vdc, nominal;
range 18 to 31Vdc.
Current Drain (at 25°C, 28Vdc):
10mA (max.), plus load current.
Reverse Polarity Protection:
The timer will not be damaged or operate
when input voltage polarity is reversed.
Output Data:
Configuration:
1 Form A (SPST-NO)
solid state switch closure to ground.
Load Ratings:
Resistive:
300mA @ +25°C, derated to
100mA @ +125°C.
Inductive:
Three MIL-R-5757/9 relays
(any relay with 26.5Vdc coil).
Lamp Load:
Two MS25237-327 lamps
per MIL-L-6363.
Load Suppression:
Suppression for
inductive loads for output protection is
provided within the unit.
Voltage Drop:
2.5Vdc, max. @ -55°C
and +25°C; 2.0 Vdc, max., @ +125°C.
Leakage Current:
1µA, max. @
+25°C, 10µA, max. @ +125°C.
Insulation Resistance:
1,000
megohms, min., @ 500Vdc, measured
between all terminals tied together to the
case.
Dielectric Strength:
500Vrms, 60 Hz.,
at sea level, measured between all
terminals tied together to the case.
Transients:
Voltage Surge:
Per MIL-STD-704A,
figure 9, limit 1, for category B
equipment.
Self-generated Spikes:
±10V.
CII 6001 series delay on
operate timer modules are
miniature devices combining
solid state timing circuits with
solid state switch outputs in
robust hermetically sealed DIP
enclosures. The 1 Form A
(SPST-NO) switch is rated
300mA.
Part Numbering System
Typical Part Number
6001
–6002
Model Number:
6001 = Fixed timer, -55°C to +125°C
Timing Code:
Four-digit code for any value between 50ms and 600s.
The timing code consists of four digits and gives the time in ms. The first
three digits are the significant figures and the last digit is the number of zeros
following the significant figures; thus 50 ms would be coded 0500, 1.1 s
would read 1101, and 1 m (60 s) would be 6002.
Optional Suffix:
C = Commercial version equivalent to M83726/13.
C
Timing Diagram
INPUT
LOAD
+28Vdc
0Vdc
ON
OFF
< TIME DELAY >
A typical part number would be 6001–6002C. This solid state output timing module
has a time delay of 60s at 28Vdc and is the commercial equivalent to M83726/13.
Environmental Specifications
Temperature Range:
-55°C to +125°C.
Altitude:
80,000 ft.
Shock:
150 G’s, 11 ± 1ms half-sine
wave.
Vibration (sinusoidal):
10 -80 Hz. at
0.06 inch DA; 80 - 3,000 Hz. at 20 G’s.
Sealing:
MIL-STD-202, method 112,
condition C.
Materials:
Cover:
Nickel.
Header:
Kovar.
Pins:
Kovar, gold plated.
Marking:
Per MIL-R-83726.
Weight:
0.42 oz (12g) max.
Outline Dimensions
.920 MAX.
[23.375]
.42 MAX.
[10.67]
.100 TYP.
[2.54]
.018 DIA. TYP.
[14.7]
COLORED BEAD
.06
[1.52]
.28
[7.11]
.58 MAX.
[14.7]
.300
[7.62]
14 PINS GOLD PLATE PER
MIL-G-45204, TYPE II, CLASS I,
UNDERPLATING, NICKEL 50 TO
150 MICROINCHES THICK.
3 TERMINALS FOR
CIRCUIT CONNECTIONS
Wiring Diagram
+
LOAD
B+
–
B–
– +
INPUT
PIN 10 IS ACTIVE. DO NOT CONNECT.
Special Notes:
• Load is connected between B+ and terminal designated. Delay begins upon
application of power to terminals (B+ and B–).
• Always consult latest military specification for changes and additional information.
© 2005 by Tyco Electronics Corporation. All Rights Reserved.
CII and TYCO are trademarks.
Other products and company names mentioned herein may be trademarks of their respective owners.
1
Catalog 8-1773439-2
Revised 4-05
www.tycoelectronics.com
Dimensions are in inches and
millimeters unless otherwise
specified. Values in brackets
are metric equivalents.
Dimensions are shown for
reference purposes only.
Specifications subject
to change.
USA: 1-800-522-6752
Canada: 1-905-470-4425
Mexico: 01-800-733-8926
C. America: 52-55-5-729-0425
South America: 55-11-3611-1514
Hong Kong: 852-2735-1628
Japan: 81-44-844-8013
UK: 44-141-810-8967
FPGA/CPLD
京公网安备 11010802033920号
EEWORLD
