EEWORLDEEWORLDEEWORLD

Part Number

Search

LM119J/883

Description
IC COMPARATOR, Comparator
CategoryAnalog mixed-signal IC    Amplifier circuit   
File Size182KB,12 Pages
ManufacturerLinear ( ADI )
Websitehttp://www.analog.com/cn/index.html
Download Datasheet Parametric View All

LM119J/883 Overview

IC COMPARATOR, Comparator

LM119J/883 Parametric

Parameter NameAttribute value
Is it Rohs certified?incompatible
MakerLinear ( ADI )
package instructionDIP, DIP14,.3
Reach Compliance Codecompliant
ECCN codeEAR99
Amplifier typeCOMPARATOR
Maximum bias current (IIB) at 25C0.5 µA
Maximum input offset voltage7000 µV
JESD-30 codeR-XDIP-T14
JESD-609 codee0
Nominal Negative Supply Voltage (Vsup)-15 V
Number of terminals14
Maximum operating temperature125 °C
Minimum operating temperature-55 °C
Package body materialCERAMIC
encapsulated codeDIP
Encapsulate equivalent codeDIP14,.3
Package shapeRECTANGULAR
Package formIN-LINE
Peak Reflow Temperature (Celsius)NOT SPECIFIED
power supply+-15 V
Certification statusNot Qualified
Nominal response time80 ns
Filter level38535Q/M;38534H;883B
Maximum slew rate11.5 mA
Nominal supply voltage (Vsup)15 V
surface mountNO
technologyBIPOLAR
Temperature levelMILITARY
Terminal surfaceTin/Lead (Sn/Pb)
Terminal formTHROUGH-HOLE
Terminal pitch2.54 mm
Terminal locationDUAL
Maximum time at peak reflow temperatureNOT SPECIFIED
LT119A/LT319A
LM119/LM319
Dual Comparator
FEATURES
n
n
n
n
n
DESCRIPTION
The LT
®
119A is an improved version of the LM119 dual
comparator. It features lower input offset voltage and
offset current, higher voltage gain, guaranteed common
mode rejection and input protection diodes.
The LT119A is capable of operation over a supply range
from 5V to ±15V and can drive 25mA loads from each
open collector output. A separate ground pin allows the
LT119A to isolate system grounds.
Linear Technology Corporation’s advanced processing,
design techniques and reliability make the LT119A/LT319A
an ideal choice over previous devices in most comparator
applications.
L,
LT, LTC, LTM, Linear Technology and the Linear logo are registered trademarks of Linear
Technology Corporation. All other trademarks are the property of their respective owners.
Guaranteed
Maximum 0.5mV Input Offset Voltage
Input Protection Diodes
Operates From Single 5V Supply
25mA Drive Capability
80ns Response Time
APPLICATIONS
n
n
n
n
Window Detectors
High Speed One Shot
Relay/Lamp Drivers
Voltage Controlled Oscillators
TYPICAL APPLICATION
Window Detector*
5V
OUTPUT
VOLTAGE (V)
V
UT
V
IN
3
Response Time For Various Input Overdrives
6
5
4
3
2
1
20mV
2mV
5mV
+
10
1
500
TTL OUTPUT
1/2 LT319A
4
2
8
INPUT
VOLTAGE (mV)
+
1/2 LT319A
6
7
V
OUT
= 5V FOR
V
LT
≤ V
IN
≤ V
UT
V
OUT
= 0V FOR
V
IN
≤ V
LT
OR V
IN
≤ V
UT
0
100
50
0
0
50
V
S
= ±15V
R
L
= 500
V
+ +
= 5V
T
A
= 25°C
V
LT
9
5
100 150 200 250 300 350
TIME (ns)
LT119/319 TA2
LT119/319 TA1
*
ALLOWED WINDOW FOR SINGLE 5V SUPPLY IS 1.2V TO 3.8V
119a319afc
1
[Help] What is the reason for this?
I use the classic serial port test program, and the sending and receiving are normal during online simulation. However, if only the external power supply is used, and the emulator is not connected, th...
louislen Microcontroller MCU
Request schematic
TMS320F2812...
sandlake FPGA/CPLD
Face recognition model building process
[i=s]This post was last edited by swzswz on 2022-10-21 19:08[/i]Face recognition modelFace recognition model steps Face recognition is mainly divided into two models:Detection network modelClassificat...
swzswz DigiKey Technology Zone
IAR EMARM V5 embedded system application programming and development
If anyone has an electronic copy of "IAR EMARM V5 Embedded System Application Programming and Development", please send me one. I have been looking for it online for a long time but can't find it. Tha...
lnhjsdf DIY/Open Source Hardware
Going crazy, 100 points eVC test
} DWORD JMP_Open(DWORD hDeviceContext,DWORD AccessCode,DWORD ShareMode) { //Initialize related pins return 1; } BOOL JMP_Close(DWORD hOpenContext) { //Restore pin status } BOOL JMP_IOControl(DWORD hOp...
xurong1124 Embedded System
In the evc4.0 development environment, the problem of filling the outer and inner rings of polygons
I have a question. In the evc4.0 development environment, I have worked on a project to fill the outer and inner rings of polygons. I used the polypolygon function, but it does not support evc. It wor...
xianghonghe Embedded System

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2163  157  595  482  149  44  4  12  10  3 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号