EEWORLDEEWORLDEEWORLD

Part Number

Search

212X0102N228SN3

Description
Rotary Switch, 2 Positions, SPDT, Latched, 0.25A, 28VDC, Solder Terminal, Slot Shaft Trim Actuator, Through Hole-right Angle, ROHS COMPLIANT
CategoryMechanical and electronic products    switch   
File Size1MB,3 Pages
ManufacturerCTS
Environmental Compliance
Download Datasheet Parametric View All

212X0102N228SN3 Overview

Rotary Switch, 2 Positions, SPDT, Latched, 0.25A, 28VDC, Solder Terminal, Slot Shaft Trim Actuator, Through Hole-right Angle, ROHS COMPLIANT

212X0102N228SN3 Parametric

Parameter NameAttribute value
Is it lead-free?Lead free
Is it Rohs certified?conform to
package instructionROHS COMPLIANT
Reach Compliance Codeunknow
ECCN codeEAR99
Actuator typeSLOT SHAFT TRIM
body height39.95 mm
Body length or diameter36.6 mm
Maximum contact current (DC)0.25 A
Contact (DC) maximum rated R load.25A@28VDC
Maximum contact voltage (DC)28 V
Electrical life25000 Cycle(s)
Graduation angle60 deg
JESD-609 codee4
Manufacturer's serial number212
Installation featuresTHROUGH HOLE-RIGHT ANGLE
Number of positions2
Number of switching segments1
surface mountNO
Switch actionLATCHED
switch functionSPDT
Switch typeROTARY SWITCH
Terminal surfaceSilver (Ag)
Termination typeSOLDER
Base Number Matches1
Panel Seal
Available with bushing and shaft seal
1
4
3 05 14
Can anyone help me analyze the circuit? Please explain in detail. Thanks!
Please help analyze this circuit in detail. Thank you very much!...
xiaole47 Analog electronics
This effort is still no match for analog circuits? How to achieve flicker-free dimming with a single-chip microcomputer
:funk: I have been busy all day today, and I want to make a flicker-free dimming circuit controlled by a single-chip microcomputer. The picture is as follows:...
ichuangj 51mcu
Why can't falsh boot normally after powering on again?
The flash is programmed and works fine as long as the power is on, but it stops working as soon as the power is off. What is the reason?...
cnnbxc Analogue and Mixed Signal
FPGA learning DS1302 clock + digital tube display
[i=s]This post was last edited by gurou1 on 2017-5-14 14:52[/i] [font=楷体, 楷体_GB2312][size=5]1. Experimental purpose: Understand the working principle of DS1302 and display the hours, minutes and secon...
gurou1 FPGA/CPLD
Recommend a TI product replacement website
There is a very concise and general introduction to TI's controller products, and there are many reference solutions using this as the entry point, which is very convenient to use.The link is as follo...
wstt Microcontroller MCU
LTC3113 power supply problem help! !
I was adjusting the board these days. After soldering the LTC3113 power supply, the output voltage was not 3.3 but 0.6V. Has anyone encountered this situation? ? The feedback voltage was also 0.6V aft...
安静的白色风车 Power technology

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1013  1825  584  1848  2476  21  37  12  38  50 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号