Operating Temperature Range ........................-55°C to +125°C
Junction Temperature ..................................................... +150°C
Storage Temperature Range .............................-65°C to +150°C
Lead Temperature (soldering, 10s) ................................ +300°C
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
ELECTRICAL CHARACTERISTICS
(V
CC
= 2.7V to 5.5V, R
PULLUP
= 100kΩ (open-drain output only), T
A
= -55°C to +125°C, unless otherwise noted. Typical values are at
T
A
= +25°C.) (Note 1)
PARAMETER
Supply Voltage Range
SYMBOL
V
CC
Hot-temperature thresholds
(+35°C to +115°C)
Supply Current
I
CC
Cold-temperature thresholds
(-45°C to +15°C)
-15°C to +65°C
Temperature Threshold Accuracy
(Note 2)
Temperature Threshold
Hysteresis
HYST Input Logic Level (Note 4)
Logic Output Voltage High
(Push-Pull)
Logic Output Voltage Low
(Push-Pull and Open Drain)
Open-Drain Output Leakage
Current
OUT TEMPERATURE SENSITIVITY
Error to Equation:
OUT = 1.8015V - 10.62mV(T - 30)
- 1.1µV (T - 30)
2
Sensor Gain
OUT Capacitive Load (Note 4)
OUT Load Regulation
OUT Line Regulation
0 < I
OUT
< 40µA
-1µA < I
OUT
< 0
0.02
0.04
0.3
-30°C to +125°C, V
CC
= 2.7V to 5.5V
-55°C to -30°C (Note 3)
-2
-5
-10.62
1000
0.24
+2
+2
°C
mV/°C
pF
°C
°C/V
∆T
TH
+75°C to +115°C
-45°C to -25°C (Note 3)
T
HYST
V
IH
V
IL
V
OH
V
OL
I
SOURCE
= 500µA, V
CC
> 2.7V
I
SOURCE
= 800µA, V
CC
> 4.5V
I
SINK
= 1.2mA, V
CC
> 2.7V
I
SINK
= 3.2mA, V
CC
> 4.5V
V
CC
= 2.7V, open-drain output = 5.5V
10
0.8 x V
CC
V
CC
- 1.5
0.3
0.4
HYST = V
CC
HYST = GND
0.8 x V
CC
0.2 x V
CC
-1.5
-2.5
-3
2
10
CONDITIONS
MIN
2.7
22
40
+1.5
+2.5
+3
°C
V
V
V
nA
°C
TYP
MAX
5.5
40
µA
UNITS
V
Note 1:
100% production tested at T
A
= +25°C. Specifications over temperature are guaranteed by design.
Note 2:
The MAX6516–MAX6519 are available with internal factory-programmed temperature trip thresholds from -45°C to +115°C
in 10°C increments.
Note 3:
V
CC
must be greater than 4.5V for a switching threshold of -45°C.
I created a thread in the driver's DriverEntry to read a file. However, after reading the file in the thread function, I used PsTerminateSystemThread to end the thread, but I found that the thread was...
Soft errors are " disturbances " ( i.e., data loss ) in semiconductor devices that cannot be intentionally reproduced . They are caused by external factors that are beyond the designer's control, incl...
[size=4][color=#000000]At first, I didn’t feel anything when reading the manual, so I went to read the code (and found it even less interesting), mainly because the register definitions were not clear...
It is recommended to organize the commonly used tool software categories in the download center, or to create an index interface to provide installation packages of various tool software for everyone ...
In the previous article, I wrote a simple GPIO running light test, which looked a bit monotonous. I was used to serial port debugging. If there was no serial port on the board, I had to find another ...[Details]
In 1952, Bell Labs built a 6-foot-tall automatic number recognition machine called "Audrey", which could recognize the pronunciation of the numbers 0 to 9 with an accuracy of more than 90%. And its...[Details]
ZTE was punished, and Hou Weigui, who had already retired, had to come out of retirement again and run around to mediate. Let's follow the embedded editor to learn about the relevant content.
...[Details]
This paper combines embedded control technology with network control technology to realize the design of temperature control system based on single chip microcomputer through Internet control. Th...[Details]
Household photovoltaic power stations mainly utilize idle resources on existing household buildings, such as roofs, wall facades, balconies, courtyards, etc., to install and use distributed photovo...[Details]
This program sets the LED running light and the 0-16 numbers of the 0th position of the digital tube to light up in a cycle. The digital tube program cannot be put into the main function, because the...[Details]
Assume that the MCS-51 microcontroller uses a 12MHz crystal oscillator, and wants to use a timer to generate a pulse with a duty cycle of about 30% and a period of 60ms at port P1.0. ;==============...[Details]
In 2014, the production and sales of new energy vehicles in China exceeded 80,000 units, and the development trend is encouraging. In order to enable new energy enthusiasts and junior R&D personnel t...[Details]
Semiconductor giant Intel has launched the desktop version of the 8th generation Coffee Lake architecture
Core
processor more than a month ago, and its performance is said to be 30% to 40% ...[Details]
Σ-ΔA/D technology has the characteristics of high resolution, high linearity and low cost. Based on TI's MSP430F1121 microcontroller, this paper introduces a high-precision A/D implementation scheme ...[Details]
Recently, the 2017 Review and 2018 Outlook Seminar of the Photovoltaic Industry was held in Beijing. Sungrow, a powerful inverter technology company, was invited to attend the seminar. With 20 year...[Details]
At the beginning of 2018, when interviewed by a reporter from China Business Weekly, Rong Yongkang, global vice president of Amazon
AWS
(cloud computing service) and executive director of G...[Details]
Embedded System
京公网安备 11010802033920号
EEWORLD
