EEWORLDEEWORLDEEWORLD

Part Number

Search

X40031V14-A

Description
3-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDSO14
Categoryaccessories   
File Size314KB,21 Pages
ManufacturerIntersil ( Renesas )
Websitehttp://www.intersil.com/cda/home/
Download Datasheet View All

X40031V14-A Overview

3-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDSO14

®
X40030, X40031, X40034, X40035
Data Sheet
April 28, 2005
FN8114.0
PRELIMINARY
Triple Voltage Monitor with Integrated
CPU Supervisor
FEATURES
• Triple voltage detection and reset assertion
—Standard reset threshold settings
See selection table on page 2.
—Adjust low voltage reset threshold voltages
using special programming sequence
—Reset signal valid to V
CC
= 1V
—Monitor three seperate voltages
• Fault detection register
• Selectable power on reset timeout
(0.05s, 0.2s, 0.4s, 0.8s)
• Selectable watchdog timer interval
(25ms, 200ms, 1.4s or off)
• Debounced manual reset input
• Low power CMOS
—25µA typical standby current, watchdog on
—6µA typical standby current, watchdog off
• 400kHz 2-wire interface
• 2.7V to 5.5V power supply operation
• Available packages
—14-lead SOIC, TSSOP
• Monitor Voltages: 5V to 0.9V
• Independent Core Voltage Monitor
APPLICATIONS
• Communication Equipment
—Routers, Hubs, Switches
—Disk arrays, Network Storage
BLOCK DIAGRAM
V3MON
• Industrial Systems
—Process Control
—Intelligent Instrumentation
• Computer Systems
—Computers
—Network Servers
DESCRIPTION
The X40030, X40031, X40034, X40035 combines
power-on reset control, watchdog timer, supply voltage
supervision, second and third voltage supervision, and
manual reset, in one package. This combination lowers
system cost, reduces board space requirements, and
increases reliability.
Applying voltage to V
CC
activates the power on reset
circuit which holds RESET/RESET active for a period of
time. This allows the power supply and system oscilla-
tor to stabilize before the processor can execute code.
Low V
CC
detection circuitry protects the user’s system
from low voltage conditions, resetting the system
when V
CC
falls below the minimum V
TRIP1
point.
RESET/RESET is active until V
CC
returns to proper
operating level and stabilizes. A second and third volt-
age monitor circuit tracks the unregulated supply to
provide a power fail warning or monitors different
power supply voltage. Three common low voltage
combinations are available, however, Intersil’s unique
circuits allows the threshold for either voltage monitor
to be reprogrammed to meet specific system level
requirements or to fine-tune the threshold for applica-
+
V3 Monitor
Logic
-
V
TRIP3
V3FAIL
V
CC
or
V2MON*
V2FAIL
V
TRIP2
V2MON
+
V2 Monitor
Logic
-
SDA
Data
Register
Command
Decode Test
& Control
Logic
Fault Detection
Register
Status
Register
Watchdog
and
Reset Logic
WDO
WP
MR
SCL
V
CC
(V1MON)
+
V
CC
Monitor
Logic
V
TRIP1
-
Power on,
Manual Reset
Low Voltage
Reset
Generation
RESET
X40030/34
RESET
X40031/35
LOWLINE
1
CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
1-888-INTERSIL or 1-888-352-6832
|
Intersil (and design) is a registered trademark of Intersil Americas Inc.
Copyright Intersil Americas Inc. 2005. All Rights Reserved
All other trademarks mentioned are the property of their respective owners.
ADS830/831 data collection is seriously jittery
What is the reason? I know it's hard to say, but I connected it according to the datasheet. The effect is not good when using opa694 as the pre-stage follower input. It is not good when using opa690. ...
523335234 FPGA/CPLD
【Share your experience】Official video link related to CC2541
TI BLE course (I): Bluetooth low energy technology and its characteristics [url=http://v.youku.com/v_show/id_XNTk4MDUyODM2.html]http://v.youku.com/v_show/id_XNTk4MDUyODM2.html[/url] TI BLE course (II)...
fsyicheng Analogue and Mixed Signal
ROHM Sensor Evaluation Kit (2) Use of Sensor Shield and software platform construction
[i=s]This post was last edited by x1816 on 2017-2-18 18:29[/i] [font=黑体][size=6][b]Shield board introduction[/b][/size][/font] [font=微软雅黑][size=3]Shield board is the bridge connecting the sensor board...
x1816 Sensor
CRC - Is this a bug?
Using STM32F103ZET6, the code is as follows int main(void) { int getdr; RCC_AHBPeriphClockCmd( RCC_AHBPeriph_CRC , ENABLE); CRC->CR = 1; CRC->DR = 0x0; getdr = CRC->DR; while (1){} } Including turning...
akatosh stm32/stm8
【Help】Everyone come in and help
I am making a simple gadget that communicates via the UART port. There is no RESET button on the 149 circuit, so it is reset by power-on.The program is written and the hardware simulation is true, wit...
会流泪的鱼 Microcontroller MCU
Production of single-phase variable frequency power supply
[i=s]This post was last edited by paulhyde on 2014-9-15 04:18[/i] This is the first time we have worked on a power supply topic, and it is a topic known as the most difficult power supply. The inverte...
liuyong1989 Electronics Design Contest

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2165  143  137  1725  1340  44  3  35  27  47 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号