This course mainly introduces the products, positioning, applications, selection and huge resource library of Infineon point load solutions. [url=https://download.eeworld.com.cn/detail/soso/561914]>>C...
I have a question for everyone. ADS is used for bare boards and PB is used for systems. So what should be used for drivers? ? Can anyone help me distinguish between ADS and PB? I still can't tell them...
When increasing the voltage from 21V to 36V and connecting a 50-ohm load, it is found that the power must be turned on first and then the load is connected. If the load is connected and then powered, ...
I wrote a simple serial port program using AT89S52. After writing the program into the chip, it can receive data normally. However, when the AT89S52 is powered off and then powered on, it cannot recei...
In ordinary low-frequency digital-analog mixed circuit applications, the most likely interference is common-channel coupling interference, not crosstalk. The following is an example of a design applic...
Title: M68HC11 MCU Principle, Application and Technology Manual/MOTOROLA MCU Development and Application Series Author: Tu Shiliang Editor-in-Chief Publisher: Fudan University Press Publication Date: ...
ZTE was punished, and Hou Weigui, who had already retired, had to come out of retirement again and run around to mediate. Let's follow the embedded editor to learn about the relevant content.
...[Details]
The adoption of vehicle tracking systems for cars and fleets is increasing. Modern trackers have reduced form factors and increased functionality to support active data transmission for real-time tra...[Details]
The ZTE incident has aroused people's concerns about the future of Chinese chips, and they have been using WeChat and Weibo to express their views; the Chinese display industry is also worried abou...[Details]
The pins of stm32 have two uses: GPIO (general purpose io) and AFIO (alternate function io) For some pins (depending on the chip), neither of these two uses exists. For example, in 64-pin products, O...[Details]
1. Function and purpose There are two pins BOOT0 and BOOT1 on each STM32 chip. The level status of these two pins when the chip is reset determines which area the program starts from after th...[Details]
I have encountered many problems when tinkering with LD driver recently. I will record them one by one below. Otherwise, who will remember who in five hundred years? 1. Configuration issues of multi-...[Details]
The following is a 16-way multi-channel ADC acquisition circuit diagram and source program made using the STM32 microcontroller. It uses a USB interface to connect to the computer, which is actually ...[Details]
MCS-51 single-chip microcomputer, a simple assembly language program, calculates the function value of a piecewise function. It is known that there is a variable X in the 25H unit. It is required to ...[Details]
;The hardware connection circuit of the 51 single-chip microcomputer is as follows: ;P1.3 and P1.4 are each connected to a button; ;P0.0 and P0.3 are each connected to a light-emitting diode; ;P2.0~P...[Details]
Each I/O port of the AVR microcontroller corresponds to three registers: DDRx, PORTx and PINx, where DDRx is the data direction, i.e. input or output; PORTx is the state of the internal pull-up r...[Details]
"When the spring breeze blows, the horses gallop." This is
a true portrayal of the development of
NB-IoT
(Narrowband Internet of Things) in China and even the world in the past two years. Le...[Details]
This article will introduce how to make an electronic keyboard using SPCE061A, and provide source code. If you have an experiment box from Lingyang University, it will be easy to complete, just a mat...[Details]
In November 2017, Apple launched the iPhone X. Among them, the most popular feature that aroused heated discussions among the public and was reported by the media was the "face recognition unlockin...[Details]
Power technology
京公网安备 11010802033920号
EEWORLD
