EEWORLDEEWORLDEEWORLD

Part Number

Search

BU-63149D3-202W

Description
Line Driver/Receiver, 2 Driver, Hybrid, CDFP36
CategoryAnalog mixed-signal IC    Drivers and interfaces   
File Size65KB,8 Pages
ManufacturerData Device Corporation
Download Datasheet Parametric View All

BU-63149D3-202W Overview

Line Driver/Receiver, 2 Driver, Hybrid, CDFP36

BU-63149D3-202W Parametric

Parameter NameAttribute value
Is it Rohs certified?incompatible
MakerData Device Corporation
Reach Compliance Codecompliant
ECCN codeEAR99
Differential outputYES
Number of drives2
High level input current maximum value0.0001 A
JESD-30 codeR-XDFP-F36
JESD-609 codee0
Number of terminals36
Maximum operating temperature85 °C
Minimum operating temperature-40 °C
Minimum output swing20 V
Maximum output low current0.0034 A
Package body materialCERAMIC
encapsulated codeDFP
Encapsulate equivalent codeFL36,.8,100
Package shapeRECTANGULAR
Package formFLATPACK
power supply5 V
Certification statusNot Qualified
Maximum receive delay
Maximum slew rate520 mA
Nominal supply voltage5 V
surface mountYES
technologyHYBRID
Temperature levelINDUSTRIAL
Terminal surfaceTin/Lead (Sn/Pb)
Terminal formFLAT
Terminal pitch2.54 mm
Terminal locationDUAL
BU-63147 and BU-63149
MIL-STD-1553 DATA BUS
+5V TRANSCEIVER
DESCRIPTION
The BU-63147/49 transceiver is a com-
plete dual transmitter and receiver pair
conforming fully to MIL-STD-1553A
and 1553B. Features include: mono-
lithic design, +5V power supply voltage,
Harris or Smiths type decoder inter-
face, completely independent dual
redundant operation, and small size
(36 pin DIP). The receiver section of
the BU-63147/49 series accepts
phase-modulated bipolar data from a
MIL-STD-1553 Data Bus and pro-
duces TTL Signal data at its output.
RX DATA OUT and
RX DATA OUT
These outputs represent positive and
negative variations of the input data
signals beyond an internally fixed
threshold level. An external STROBE
input enables or disables the receiver’s
outputs.
The transmitter section accepts
bi-phase TTL signal data at its
TX DATA IN and
TX DATA IN
inputs
and produces phase-modulated
bipolar data at the TX DATA OUT and
TX DATA OUT
outputs.
The
transmitter’s output voltage level is
typically about 11Vpp. An external
input, INHIBIT, takes priority over the
transmitter inputs and disables the
transmitter when activated with a logic
“1”.
The small size, +5V power supply volt-
age,
and
compliance
with
MIL-STD-1553 simplify engineering
design, making it an excellent choice
for interfacing with any MIL-STD-1553
system.
FEATURES
+5V Power Supply
Low Power
Conforms Fully To MIL-STD-1553A
AND 1553B
Dual Transceiver
Available with MIL-STD-1760
Compliant Transmitter Voltage
Available with McAir Compatible
Waveform
36-Pin DIP
HARRIS or SMITHS I/O
Compatibility
+5 V
1553
DATA
BUS
RECEIVER STROBE
BI PHASE
TTL DATA
COMPARATOR
RX DATA OUT
RX DATA OUT
DECODER
PHASE MODULATED
BIPOLAR DATA
RX DATA IN
SHORT OR
LONG STUB
COUPLING
ISOLATION
TRANSFORMER
RX DATA IN
RECEIVER SECTION
FILTER
FILTER
COMPARATOR
TRANSMITTER SECTION
TX Data Out
SHAPING
NETWORK
TX DATA IN
TX Data Out
SHAPING
NETWORK
ENCODER
TX DATA IN
CASE/GND
TX INHIBIT
FIGURE 1. BU-63147/49 BLOCK DIAGRAM
(one
channel shown)
©
2000
Data Device Corporation
DDS Generation Principle
I use DDS to generate three waveforms with frequencies between 100Hz and 1MHz. I use a high-speed DAC900 to output waveforms, but the output waveforms are not good, especially when the frequency reach...
2801345525 FPGA/CPLD
Help: Can you guys help me figure out this serial port issue? Thank you!
Question: When the MCU sends serial data to the PC serial port, how does the Windows system know that the MCU has sent data to it? Is it triggered by a message, or does Windows scan the serial port ev...
huangqi412 Embedded System
Damn IAR, it doesn't support STM8 yet
Damn IAR, it doesn't support STM8 yet....
pikky stm32/stm8
Can you help me check if this double-T trap circuit is correct?
Can you help me figure out if this double-T trap circuit is correct? ? What are UA and UB circuits and what is their role in the trap circuit?...
班小时 Analog electronics
Transformer Winding
I am a beginner in switching power supply. When making a forward DC-DC converter, I found that the voltage will be pulled down when the load is heavy. I suspect it is a problem with the winding of the...
yang_xian521 Power technology

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1013  635  2449  499  1451  21  13  50  11  30 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号