801-021FFBBBMNN-72 datasheet, PDF

Datasheet> All Categories > The connector> The connector> 801-021FFBBBMNN-72

801-021FFBBBMNN-72: DescriptionInterconnection Device; CategoryThe connector The connector; File Size445KB，8 Pages; ManufacturerGlenair; Websitehttp://www.glenair.com/

Download Datasheet Parametric View All

801-021FFBBBMNN-72 Overview

Interconnection Device

801-021FFBBBMNN-72 Parametric

Parameter Name	Attribute value
Maker	Glenair
Reach Compliance Code	compliant
Connector type	INTERCONNECTION DEVICE

Preview

Download Datasheet

View All

Series 80 “Mighty Mouse”

ASAP Cordsets For Ethernet, IEEE 1394 and USB 2.0

ASAP Cordsets For High Speed Serial Data

Upgrade commercial high speed serial interconnects

mil spec performance. Glenair’s ASAP “Mighty Mouse”

cordsets are available for 100BASE-T, Gigabit Ethernet,

IEE 1394 and USB 2.0 applications.

These cordsets combine aerospace-grade data cables

with Series 80 “Mighty Mouse” harsh environment

connectors for maximum performance and minimum

size.

FEP jackets

meet FAA flammability requirements. Or,

choose

low smoke/ zero halogen polyurethane jackets

for mass transit or shipboard applications.

100BASE-T Cordset With 4 Pin Series 800

Connector

Three Strain Relief Options

– Overmolded, threaded

backshell or heatshrink boots.

HOW TO ORDER CORDSETS

Step 1: Select the Connector Series

Table1 lists the six types of Series 80 connectors. For more information on selecting

a connector, please refer to the connector selection chart in the Introduction.

Step 2: Select the Cable

Table 2 contains speciﬁcations for standard data cables. The cable type also

determines the connector layout.

4 pin connectors are used for 4 wire cables,

and tem pin connectors are used for 8 wire cocables.

Step 3: Select a Cable Jacket

Table 3 shows available jacket options. Choose FEP ﬂourocarbon jackets

for airframe and avionics applications, or choose low smoke/zero halogen

polyurethane jackets for soldier systems, vehicles, and transit systems.

Step 4: Select a Cable-To-Connector Interface

Table 3 provides three ways to attach the cable to the connector:

1. Polyamide boot, overmolded with ﬂexible strain relief

2. Aluminum backshell, shielded, watertight a nd removable

3. Heat-shrink boot, low smoke/ zero halogen

Step 5: Select a Connector Conﬁguration

Table 1 shows connector codes for specifying plug versus receptacle and pin

versus socket contacts. Add a plating code, keying option and length.

CAGE Code 06324/0CA77

Printed in U.S.A.

GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912

www.glenair.com

J-1

E-Mail: sales@glenair.com

Recommended Resources

Acousto-optic digital level detector circuit diagram

Off-hook signal detection circuit

Laser detector circuit diagram

555 three-color flashing circuit

Infrared remote control electric fan circuit

Half-bridge converter electrical schematic diagram

TimerA frequency measurement problem: [color=rgb(34,34,34)][backcolor=rgb(238,238,238)][font=Tahoma][backcolor=white]Help, I can't measure the frequency with launchpad TimerA. Here is the code[/backcolor][/font][/backcolor][/color]...; someonewho Microcontroller MCU

Is there any way to set a time to jump out of the ReadFile infinite loop if the read fails?: In the USB program, I have opened and read and write data from a HID device. But if(ReadFile( deviceHandle[IndexInFieldList], // handle of file to read buffer, // pointer to buffer that receives data ...; hanbing841208 Embedded System

【CH554 Review】Part 2 Compilation, Software Development Environment Review: [i=s]This post was last edited by yang_alex on 2017-10-6 17:54[/i] The previous article talked about the hardware of CH554, and this article will talk about the software of CH554. After all, Qinheng i...; yang_alex MCU

DSP——F28335 flash programming problem: [font=微软雅黑][color=#000000][size=10pt]I use the F28335 to debug the program. It can run in RAM, but when it is burned into FLASH, it stops when it enters [/size][/color][/font][font=微软雅黑][size=2][color...; weixiaohuan DSP and ARM Processors

Automatically run the user's application after Linux starts: The command to automatically run the user's application after booting or start the system service is saved in the /usr/etc/rc.local file of the root file system of the development board. Some developm...; jxb01033016 Linux and Android

Fluke Award-winning Live Broadcast | Basics of Data Loggers, Their Applications and Calibration: Live broadcast time:December 7, 2022 (Wednesday) 10:00-11:30 amLive Topic Basic knowledge of data loggers, their applications and calibrationLive Broadcast Introduction Analyze the structural characte...; EEWORLD社区 Integrated technical exchanges

Shortcut: A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 AA AB AC AD AE AF AG AH AI AJ AK AL AM AN AO AP AQ AR AS AT AU AV AW AX AY AZ B0 B1 B2 B3 B4 B5 B6 B7 B8 B9 BA BB BC BD BE BF BG BH BI BJ BK BL BM BN BO BP BQ BR BS BT BU BV BW BX BY BZ C0 C1 C2 C3 C4 C5 C6 C7 C8 C9 CA CB CC CD CE CF CG CH CI CJ CK CL CM CN CO CP CQ CR CS CT CU CV CW CX CY CZ D0 D1 D2 D3 D4 D5 D6 D7 D8 D9 DA DB DC DD DE DF DG DH DI DJ DK DL DM DN DO DP DQ DR DS DT DU DV DW DX DZ

Popular Components