MV22V2AD-R1.5000MHZ datasheet, PDF

Datasheet> All Categories > Passive components> oscillator> MV22V2AD-R1.5000MHZ

MV22V2AD-R1.5000MHZ: DescriptionCMOS/TTL Output Clock Oscillator, 1.5MHz Min, 160MHz Max, 1.5MHz Nom, ROHS COMPLIANT, DIP-14/4; CategoryPassive components oscillator; File Size405KB，1 Pages; ManufacturerMtronPTI; Websitehttp://www.mtronpti.com; Environmental Compliance

Download Datasheet Parametric View All

MV22V2AD-R1.5000MHZ Overview

CMOS/TTL Output Clock Oscillator, 1.5MHz Min, 160MHz Max, 1.5MHz Nom, ROHS COMPLIANT, DIP-14/4

MV22V2AD-R1.5000MHZ Parametric

Parameter Name	Attribute value
Is it Rohs certified?	conform to
Maker	MtronPTI
package instruction	DIP4/14,.3
Reach Compliance Code	unknown
Maximum control voltage	4.5 V
Minimum control voltage	0.5 V
maximum descent time	10 ns
Frequency Adjustment - Mechanical	NO
Frequency offset/pull rate	100 ppm
frequency stability	500%
JESD-609 code	e1
linearity	10%
Manufacturer's serial number	MV
Installation features	THROUGH HOLE MOUNT
Number of terminals	4
Maximum operating frequency	160 MHz
Minimum operating frequency	1.5 MHz
Nominal operating frequency	1.5 MHz
Maximum operating temperature	85 °C
Minimum operating temperature	-40 °C
Oscillator type	CMOS/TTL
Output load	10 TTL, 50 pF
Package body material	METAL
Encapsulate equivalent code	DIP4/14,.3
physical size	20.8mm x 13.2mm x 5.08mm
power supply	5 V
Certification status	Not Qualified
longest rise time	10 ns
Maximum slew rate	40 mA
Maximum supply voltage	5.25 V
Minimum supply voltage	4.75 V
Nominal supply voltage	5 V
surface mount	NO
maximum symmetry	40/60 %
Terminal surface	Tin/Silver/Copper (Sn/Ag/Cu)

Preview

Download Datasheet

View All

MV Series

14 DIP, 5.0 Volt, HCMOS/TTL, VCXO

This product is not

recommended for new designs

•

General purpose VCXO for Phase Lock Loops

(PLLs), Clock Recovery, Reference Signal Tracking,

and Synthesizers

Frequencies up to 160 MHz

Tri-state Option Available

Pin Connections

MtronPTI reserves the right to make changes to the product(s) and service(s) described herein without notice. No liability is assumed as a result of their use or application.

Please see

www.mtronpti.com

for our complete offering and detailed datasheets. Contact us for your application specific requirements: MtronPTI

1-800-762-8800.

Revision: 11-16-10

Recommended Resources

Low voltage circuit breaker protection circuit d

Three-terminal voltage stabilizing chip series voltage stabilization and current expansion circuit diagram

Single junction transistor controllable pulse generator

Application circuit diagram of SG3525A single-ended output stage

JJlB-90～315/660-2 type auto-coupling step-down starter circuit

845ddr computer motherboard circuit diagram_17

【Discussion post】Hide the mouse in ce: Without further ado, let's get to the point. Hide when it's time to hide, and show when it's time to show. Method 1: ShowCrusor() but ce doesn't support it. Give up method 2: Use SetCrusor() to replac...; kcl123 Embedded System

Explain the settings of ov9650 registers: Common Control 3Bit[7]:ReservedBit[6]:Output data MSB and LSB swapBit[5:4]: ReservedBit[3]:Pin selection 0C COM3 00 RW1: Change RESET pin to EXPST_B (frame exposuremode timing) and change PWDN pin to ...; wangtengfei Embedded System

ICD2 cannot enter debug mode: My ICD2 is very strange. Some time ago, I saw a post online that said that if I set the clock in configure to XT and turn off everything else, I could enter debug mode. But yesterday, I followed the s...; crazyk MCU

[Zero-knowledge esp8266 tutorial] Quick start 30 rc-switch wireless transceiver module usage: This experiment uses the Zero-Knowledge ESP8266 and rc-switch modules.1. Experimental materialsZero-Knowledge ESP8266 development boardR433s transceiver and transmitter modulesSeveral Dupont cables 2....; roc2 stm32/stm8

About LM311 peak detection: Has anyone done LM311 peak detection? What is the highest frequency? Is there any that exceeds 2M? Please advise...; 单片机菜菜 51mcu

ADC12SC cannot be set, this problem is very strange,,,,: When using 149 to do AD experiment, I can't adjust it no matter what. After jtag debugging, I found that ADC12SC is not set, that is, the ADC12 core is not started. ENC and other bits are already set....; airqj Microcontroller MCU

Shortcut: E0 E1 E2 E3 E4 E5 E6 E7 E8 E9 EA EB EC ED EE EF EG EH EI EJ EK EL EM EN EO EP EQ ER ES ET EU EV EW EX EY EZ F0 F1 F2 F3 F4 F5 F6 F7 F8 F9 FA FB FC FD FE FF FG FH FI FJ FK FL FM FN FO FP FQ FR FS FT FU FV FW FX FY FZ G0 G1 G2 G3 G4 G5 G6 G7 G8 G9 GA GB GC GD GE GF GG GH GI GJ GK GL GM GN GO GP GQ GR GS GT GU GV GW GX GZ H0 H1 H2 H3 H4 H5 H6 H7 H8 HA HB HC HD HE HF HG HH HI HJ HK HL HM HN HO HP HQ HR HS HT HU HV HW HX HY HZ I1 I2 I3 I4 I5 I6 I7 IA IB IC ID IE IF IG IH II IK IL IM IN IO IP IQ IR IS IT IU IV IW IX J0 J1 J2 J6 J7 JA JB JC JD JE JF JG JH JJ JK JL JM JN JP JQ JR JS JT JV JW JX JZ K0 K1 K2 K3 K4 K5 K6 K7 K8 K9 KA KB KC KD KE KF KG KH KI KJ KK KL KM KN KO KP KQ KR KS KT KU KV KW KX KY KZ

Popular Components