800-024APHBBNFPA-72 datasheet, PDF

Datasheet> All Categories > The connector> The connector> 800-024APHBBNFPA-72

800-024APHBBNFPA-72: DescriptionInterconnection Device; CategoryThe connector The connector; File Size175KB，3 Pages; ManufacturerGlenair; Websitehttp://www.glenair.com/

Download Datasheet Parametric View All

800-024APHBBNFPA-72 Overview

Interconnection Device

800-024APHBBNFPA-72 Parametric

Parameter Name	Attribute value
Maker	Glenair
Reach Compliance Code	not_compliant
Connector type	INTERCONNECTION DEVICE

Preview

Download Datasheet

View All

Series 80 “Mighty Mouse”

ASAP Cordsets For Ethernet, IEEE 1394 and USB 2.0

ASAP Cordsets For High Speed Serial Data

Upgrade commercial high speed

serial interconnects

to mil-spec

performance. Glenair’s ASAP “Mighty

Mouse” cordsets are available for

100BASE-T, Gigabit Ethernet, IEE

1394 and USB 2.0 applications.

These cordsets combine aerospace-

grade data cables with Series 80

“Mighty Mouse” harsh environment

connectors for maximum

performance and minimum size.

FEP jackets

meet FAA

flammability requirements. Or,

choose

low smoke / zero halogen

polyurethane jackets

for mass

transit or shipboard applications.

Three strain relief options –

Standard overmolded cables offer

excellent strain-relief and cable

sealing.Or, choose heatshrink boots

for smallest form factor. If repairability

and ruggedness are important, choose

machined aluminum EMI backshells.

100BASE-T Cordset

with 4 Pin Series 800 Connector

HOW TO ORDER CORDSETS

Step 1: Select the Connector Series

Table1 lists the ﬁve types of Series 80 connectors. For more information on

selecting a connector, please refer to the connector selection chart on the following

page. This section does not contain ordering information for series 802 “Aqua

Mouse” cordsets. Please contact Glenair for information on hazardous environment

high pressure cables for the 802 Series.

Step 2: Select the Cable

Table 2 contains speciﬁcations for standard data cables. The cable type also

determines the connector layout.

4 pin connectors are used for 4 wire cables,

and 10 pin connectors are used for 8 wire cables.

Step 3: Select a Cable Jacket

Table 3 shows available jacket options. Choose FEP ﬂourocarbon jackets

for airframe and avionics applications, or choose low smoke/zero halogen

polyurethane jackets for soldier systems, vehicles, and transit systems.

Step 4: Select a Cable-To-Connector Interface

Table 3 provides three ways to attach the cable to the connector:

1. Polyamide boot, overmolded with ﬂexible strain relief

2. Aluminum backshell, shielded, watertight and removable

3. Heat-shrink boot, low smoke/ zero halogen

Step 5: Select a Connector Conﬁguration

Table 1 shows connector codes for specifying plug versus receptacle and pin

versus socket contacts. Add a plating code, keying option and length.

CAGE Code 06324/0CA77

Printed in U.S.A.

GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912

www.glenair.com

K-1

Rev. 05-APR-2007

E-Mail: sales@glenair.com

Recommended Resources

AD208 circuit functional block diagram

Detection circuit of sensor bridge signal

555 frequency sweep alarm circuit

Digital alarm clock circuit

LM388 with gain of 200 and load grounded

Computer motherboard circuit diagram 810 1_26

How to distinguish whether the serial port sends MT commands or normal data: As the title says, for the data sent from the serial port, how do you determine whether this frame of data is an MT command? Or is it data that needs to be transmitted? The function I want to achieve ...; mingye6 RF/Wirelessly

What's going on if the program doesn't run?: When the switching power supply is used for 103RBT6 boards, some boards work fine, but some boards can't run the program. What's going on?...; 1021256354 stm32/stm8

[Chuanglong Technology Allwinner A40i Development Board] Unboxing and resource introduction video: [i=s]This post was last edited by qinyunti on 2022-9-14 18:30[/i]video...; qinyunti Domestic Chip Exchange

How to set the ERC check and options of AD09?: The ERC check I usually use is to put the circuit board file and the schematic file into one project, and then associate them. Then check the error content in the information window. I wonder if you a...; 675452482 PCB Design

Newbie help! What do footprint and LibRef mean?: I'm a newbie and I need help from you guys! My boss asked me to make a BOM table. What do the footprint and LibRef in the original table mean? Thanks~This is the form provided by the leader. I don’t k...; 奶油曲奇 PCB Design

How to process a pulse signal with VHDL: As shown in the figure, there is an irregular pulse signal at the top. Now we want to use the delay between the two signals to represent the pulse I have just started learning VHDL. The input signals ...; yatjay FPGA/CPLD

Shortcut: S0 S1 S2 S3 S4 S5 S6 S7 S8 S9 SA SB SC SD SE SF SG SH SI SJ SK SL SM SN SO SP SQ SR SS ST SU SV SW SX SY SZ T0 T1 T2 T3 T4 T5 T6 T7 T8 T9 TA TB TC TD TE TF TG TH TI TJ TK TL TM TN TO TP TQ TR TS TT TU TV TW TX TY TZ U0 U1 U2 U3 U4 U6 U7 U8 UA UB UC UD UE UF UG UH UI UJ UK UL UM UN UP UQ UR US UT UU UV UW UX UZ V0 V1 V2 V3 V4 V5 V6 V7 V8 V9 VA VB VC VD VE VF VG VH VI VJ VK VL VM VN VO VP VQ VR VS VT VU VV VW VX VY VZ W0 W1 W2 W3 W4 W5 W6 W7 W8 W9 WA WB WC WD WE WF WG WH WI WJ WK WL WM WN WO WP WR WS WT WU WV WW WY X0 X1 X2 X3 X4 X5 X7 X8 X9 XA XB XC XD XE XF XG XH XK XL XM XN XO XP XQ XR XS XT XU XV XW XX XY XZ Y0 Y1 Y2 Y4 Y5 Y6 Y9 YA YB YC YD YE YF YG YH YK YL YM YN YP YQ YR YS YT YX Z0 Z1 Z2 Z3 Z4 Z5 Z6 Z8 ZA ZB ZC ZD ZE ZF ZG ZH ZJ ZL ZM ZN ZP ZR ZS ZT ZU ZV ZW ZX ZY

Popular Components