EEWORLDEEWORLDEEWORLD

Part Number

Search

EH3745TS-156.250MTR

Description
CRYSTAL OSCILLATOR, CLOCK, 156.25MHz, LVCMOS OUTPUT, ROHS COMPLIANT, CERAMIC, SMD, 4 PIN
CategoryPassive components    oscillator   
File Size235KB,6 Pages
ManufacturerECLIPTEK
Websitehttp://www.ecliptek.com
Environmental Compliance  
Download Datasheet Parametric View All

EH3745TS-156.250MTR Overview

CRYSTAL OSCILLATOR, CLOCK, 156.25MHz, LVCMOS OUTPUT, ROHS COMPLIANT, CERAMIC, SMD, 4 PIN

EH3745TS-156.250MTR Parametric

Parameter NameAttribute value
Is it lead-free?Lead free
Is it Rohs certified?conform to
MakerECLIPTEK
Reach Compliance Codecompliant
Other featuresTRI-STATE; ENABLE/DISABLE FUNCTION; TAPE AND REEL
maximum descent time2 ns
Frequency Adjustment - MechanicalNO
frequency stability50%
JESD-609 codee4
Manufacturer's serial numberEH37
Installation featuresSURFACE MOUNT
Nominal operating frequency156.25 MHz
Maximum operating temperature70 °C
Minimum operating temperature-10 °C
Oscillator typeLVCMOS
Output load15 pF
physical size5.0mm x 3.2mm x 1.3mm
longest rise time2 ns
Maximum supply voltage2.625 V
Minimum supply voltage2.375 V
Nominal supply voltage2.5 V
surface mountYES
maximum symmetry60/40 %
Terminal surfaceNickel/Gold (Ni/Au)
EH3745TS-156.250M TR
EH37 45
Series
RoHS Compliant (Pb-free) 2.5V 4 Pad 3.2mm x 5mm
Ceramic SMD LVCMOS Oscillator
Frequency Tolerance/Stability
±50ppm Maximum
Operating Temperature Range
0°C to +70°C
Duty Cycle
50 ±10(%)
RoHS
Pb
Packaging Options
Tape & Reel
TS -156.250M TR
Nominal Frequency
156.250MHz
Pin 1 Connection
Tri-State (High Impedance)
ELECTRICAL SPECIFICATIONS
Nominal Frequency
Frequency Tolerance/Stability
156.250MHz
±50ppm Maximum (Inclusive of all conditions: Calibration Tolerance at 25°C, Frequency Stability over the
Operating Temperature Range, Supply Voltage Change, Output Load Change, First Year Aging at 25°,
260°C Reflow, Shock, and Vibration)
±5ppm/Year Maximum
0°C to +70°C
2.5Vdc ±5%
9mA Maximum (No Load)
90% of Vdd Minimum (IOH = -8mA)
10% of Vdd Maximum (IOL = +8mA)
2nSec Maximum (Measured at 20% to 80% of waveform)
50 ±10(%) (Measured at 50% of waveform)
15pF Maximum
CMOS
Tri-State (High Impedance)
90% of Vdd Minimum or No Connect to Enable Output, 10% of Vdd Maximum to Disable Output (High
Impedance)
10µA Maximum (Pin 1 = Ground)
±100pSec Maximum
10mSec Maximum
-55°C to +125°C
Aging at 25°C
Operating Temperature Range
Supply Voltage
Input Current
Output Voltage Logic High (Voh)
Output Voltage Logic Low (Vol)
Rise/Fall Time
Duty Cycle
Load Drive Capability
Output Logic Type
Pin 1 Connection
Tri-State Input Voltage (Vih and Vil)
Standby Current
Absolute Clock Jitter
Start Up Time
Storage Temperature Range
ENVIRONMENTAL & MECHANICAL SPECIFICATIONS
ESD Susceptibility
Fine Leak Test
Flammability
Gross Leak Test
Mechanical Shock
Moisture Resistance
Moisture Sensitivity
Resistance to Soldering Heat
Resistance to Solvents
Solderability
Temperature Cycling
Vibration
MIL-STD-883, Method 3015, Class 1, HBM: 1500V
MIL-STD-883, Method 1014, Condition A
UL94-V0
MIL-STD-883, Method 1014, Condition C
MIL-STD-883, Method 2002, Condition B
MIL-STD-883, Method 1004
J-STD-020, MSL 1
MIL-STD-202, Method 210, Condition K
MIL-STD-202, Method 215
MIL-STD-883, Method 2003
MIL-STD-883, Method 1010, Condition B
MIL-STD-883, Method 2007, Condition A
www.ecliptek.com | Specification Subject to Change Without Notice | Rev A 8/14/2010 | Page 1 of 6
ROM Timing Control
Today, I used FPGA to read and write internal ROM. After carefully studying the ROM timing, I found that: for ROMs without output latches, after giving the address, valid data is retrieved after a del...
eeleader FPGA/CPLD
Could you please help me look at my schematic diagram to see if there is anything wrong?
I recently made a board. When I connected it to the emulator, the emulator light turned red. It uses the STM32F103CB chip. I don't know what the problem is. Please help me check it out.103cbdl.jpg(56 ...
langniao stm32/stm8
What is the drilling process in the Siliton ceramic substrate PCB?
PCB drilling is a process of PCB plate making, and it is also a very important step. It is mainly to punch holes in the board. For routing needs, a via is needed. For structural needs, a hole is drill...
slt12345645 PCB Design
I hope this is a good guide for you.
[i=s]This post was last edited by paulhyde on 2014-9-15 03:31[/i]...
经世致用 Electronics Design Contest
09 National Competition Guangxi Division Selection Competition Organizing Committee Recommended Test Questions
[i=s] This post was last edited by paulhyde on 2014-9-15 09:44 [/i] The test questions recommended by the organizing committee of the 2009 National Competition Guangxi Division Selection Competition a...
open82977352 Electronics Design Contest
Does anyone know if this development board is original or third-party?
I found a development board, but I don't know if it's original or a third-party one, and I can't find any information! ~...
wanghongyang Buy&Sell

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1549  2838  2726  2105  2657  32  58  55  43  54 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号