ME73ZAGFREQ-OUT7 datasheet, PDF

ME73ZAGFREQ-OUT7: DescriptionPECL 10KH Output Clock Oscillator, 19.44MHz Min, 155.52MHz Max; CategoryPassive components oscillator; File Size51KB，1 Pages; ManufacturerMtronPTI; Websitehttp://www.mtronpti.com

Download Datasheet Parametric View All

ME73ZAGFREQ-OUT7 Overview

PECL 10KH Output Clock Oscillator, 19.44MHz Min, 155.52MHz Max

Parameter Name	Attribute value
Is it Rohs certified?	incompatible
Maker	MtronPTI
Reach Compliance Code	unknown
Other features	ECL OPERATION POSSIBLE
maximum descent time	2.5 ns
Frequency Adjustment - Mechanical	NO
frequency stability	100%
Manufacturer's serial number	ME
Installation features	SURFACE MOUNT
Maximum operating frequency	155.52 MHz
Minimum operating frequency	19.44 MHz
Maximum operating temperature	85 °C
Minimum operating temperature
Oscillator type	PECL 10KH
Output load	130 OHM
physical size	20.8mm x 13.2mm x 5.1mm
longest rise time	2.5 ns
Nominal supply voltage	5 V
surface mount	YES
maximum symmetry	40/60 %

ME Series 5.0 Volt ECL/PECL

Compatible Oscillators

ME Series ECL/PECL Clock Oscillators, 10 KH

Compatible with Optional Complementary

Outputs

*Contact factory for availability.

Pin Connections

See page 90 for gull wing configuration.

1. Internally terminated outputs. See load circuit diagram #4 on page 92.

2. Rise/Fall times are measured between Vcc -0.98 V and Vcc -1.63 V.

Can the simulated 3D component diagram, AD19, be drawn without drawing it in SolidWorks and then importing it?: Are the electrolytic capacitors and three-terminal high-power tubes outlined in red in the picture drawn using SolidWorks and then imported into AD? Can it be drawn using only Altium Designer? If only...; oyhprince PCB Design

Moderator---STM32 interrupt nesting problem: Moderator, I have a question. How to disable interrupt nesting in STM32 and which register to operate? Thank you!Because when using PWM capture in TIM, it is very likely to be interfered by the outsid...; kwyxp stm32/stm8

Linux kernel setting ip problem: I downloaded the Linux kernel to the development board 2410, and the IP that came out of ifconfig was 192.168.10.220. I want to change it to 0.220, but it returns to the previous setting every time I ...; zhanggz02111 Linux and Android

FE1.1S burns out after use: When using FE1.1S, the chip and the transformer in series on D+/D- are burned out. Has anyone encountered this before? The schematic diagram is as follows:...; liang5698 Analog electronics

Embedded iTOP-4412 development board implements socket programming based on UDP: [align=left][font=宋体][size=10.5pt]This article is transferred from: [/size][/font][url=http://www.topeetboard.com]http://www.topeetboard.com[/url][/align][align=left]Platform: iTOP-4412[font=宋体]develo...; Chihiro ARM Technology

The keyboard cannot be used after the application is started with the system: The program requires the use of a keyboard. Before the application was automatically started with the system, it was placed in the system via USB, and the keyboard on the board was normal at this time...; kmmmmy Embedded System

Shortcut: L0 L1 L2 L3 L4 L5 L6 L7 L8 L9 LA LB LC LD LE LF LG LH LI LJ LK LL LM LN LO LP LQ LR LS LT LU LV LW LX LY LZ M0 M1 M2 M3 M4 M5 M6 M7 M8 M9 MA MB MC MD ME MF MG MH MI MJ MK ML MM MN MO MP MQ MR MS MT MU MV MW MX MY MZ N0 N1 N2 N3 N4 N5 N6 N7 N8 NA NB NC ND NE NF NG NH NI NJ NK NL NM NN NO NP NQ NR NS NT NU NV NX NZ O0 O1 O2 O3 OA OB OC OD OE OF OG OH OI OJ OK OL OM ON OP OQ OR OS OT OV OX OY OZ P0 P1 P2 P3 P4 P5 P6 P7 P8 P9 PA PB PC PD PE PF PG PH PI PJ PK PL PM PN PO PP PQ PR PS PT PU PV PW PX PY PZ Q1 Q2 Q3 Q4 Q5 Q6 Q8 Q9 QA QB QC QE QF QG QH QK QL QM QP QR QS QT QV QW QX QY R0 R1 R2 R3 R4 R5 R6 R7 R8 R9 RA RB RC RD RE RF RG RH RI RJ RK RL RM RN RO RP RQ RR RS RT RU RV RW RX RY RZ

Popular Components