EEWORLDEEWORLDEEWORLD

Part Number

Search

86581-352

Description
Board Connector, 52 Contact(s), 2 Row(s), Male, Straight, Solder Terminal
CategoryThe connector    The connector   
File Size614KB,8 Pages
ManufacturerAmphenol
Websitehttp://www.amphenol.com/
Download Datasheet Parametric View All

86581-352 Overview

Board Connector, 52 Contact(s), 2 Row(s), Male, Straight, Solder Terminal

86581-352 Parametric

Parameter NameAttribute value
Is it lead-free?Contains lead
Is it Rohs certified?incompatible
MakerAmphenol
Reach Compliance Codecompliant
Connector typeBOARD CONNECTOR
Contact to complete cooperationGOLD (50) OVER NICKEL (50)/GOLD FLASH (50) OVER PALLADIUM NICKEL
Contact completed and terminatedGOLD (50) OVER NICKEL (50)/GOLD FLASH (50) OVER PALLADIUM NICKEL
Contact point genderMALE
Contact materialPHOSPHOR BRONZE
DIN complianceNO
Filter functionNO
IEC complianceNO
JESD-609 codee4
MIL complianceNO
Manufacturer's serial number86581
Mixed contactsNO
Installation methodSTRAIGHT
Installation typeBOARD
Number of rows loaded2
OptionsGENERAL PURPOSE
Terminal pitch2.54 mm
Termination typeSOLDER
Total number of contacts52
UL Flammability Code94V-0
PDM: Rev:DF
STATUS:
Released
Printed: Jun 02, 2011
.
Application of DSP repetitive control technology in inverter power supply system
This paper proposes a DSP repetitive control scheme, which uses a repetitive controller to track the periodic reference command signal, reduce the output voltage harmonics, and improve the dynamic per...
Jacktang DSP and ARM Processors
The problem of PCB parasitic capacitance
[i=s] This post was last edited by S3S4S5S6 on 2017-11-9 08:48 [/i] An oscillation circuit was built using TLV3501 according to the typical application in the manual. After PCB layout, it was found th...
S3S4S5S6 PCB Design
Why can the reference layer of PCB also be the power layer?
As shown in the figure above, in a 4-layer PCB stack, why can the differential line refer to the third layer (Power layer)? I understand that ordinary single-ended signals must be referenced to the gr...
xiaominwzj PCB Design
I drew the schematic using protues software, and after converting it into a PCB diagram, I found that only the buzzer was not packaged.
I finished drawing the schematic diagram using protues software. After converting it into PCB diagram, I found that only the buzzer was not packaged. After checking online, I found that I had to draw ...
圈在指尖 PCB Design
Questions about SPI in 5438
The direction of the signal on the middle line is from slave to master. Does it mean that the slave controls the UCxSTE bit of the master? But I think it should be manually decided in the program whet...
zzbaizhi Microcontroller MCU
Basic knowledge of automobile body design
This article provides some basic knowledge of automobile body design, which is suitable for learning and training of relevant departments in the automobile industry. Main contents: Main components of ...
frozenviolet Automotive Electronics

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1447  738  294  352  1965  30  15  6  8  40 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号