output voltages. It features input voltage range of
38V to 55V, and provides up to 300W @ 48Vin of
power. Typical efficiency of 9.6V module is 96%.
It can be parallel for more power.
Conditions
V
IN
= 48V, I
O
= 0A
I
O
= 0 to 34A
V
IN
= 38 to 55V, I
O
= 0 to 34A,
Ta = 55ºC
20MHz bandwidth
Corresponding to P
O
= 240W
V
IN
= 48V, P
O
= 240W
From enable, <0.8V to V
O
> 0%
for V
IN
= 38V - 55V
From 0% to 90%
Enabled: V
IN
applied to 90% V
OUT
25% step, A/µs, ∆V
O
At P
O
= 240W
Min.
9.40
7.0
Typ.
9.50
0.4
Max.
9.60
.0
Units
V
DC
V
Vdc
mV p-p
A
%
ms
ms
ms
%V
O
%
%
%
µF
50
0
96
0.
0
50
±3
3
0
0
50
34
0
5
0
3
3
3000
V
IN
= 48Vdc, Ta = 25ºC, Airflow = 200 LFM for all data unless otherwise noted.
2 Output Ripple Voltage and noise is specified when measured with a 0uF tantalum and a µF ceramic capacitor at the output pins.
3 During output voltage rise time (5 mS Max.), output power shall be limited to 50% constant power.
Transient response is specified with a 960µF capacitor at the output of the converter.
D C / D C
C O N V E R T E R S
CDC_EUS34-096.A04
Page of 3
www.cd4power.com
Technical enquiries
email: toronto@cdtechno.com, tel: (866) 740 232
POWER ELECTRONICS DIVISION
EUS34-096
Isolated Bus Converter
Conditions
Auto-restart
Re-start rate
Auto-restart
PROTECTION CHARACTERISTICS
Parameter
Output over-current shutdown
2
Over temperature shutdown
3
Over temperature restart hysteresis
Min.
38
Typ.
40
TBD
35
0
Max.
42
40
Units
A
ms
ºC
ºC
GENERAL CHARACTERISTICS
Parameter
Isolation voltage
Isolation resistance
Storage temperature range
Operating temperature range
Operating humidity
Thermal measurement location temperature
3
Material flammability
MTBF
Conditions
Input to output
Input to output
Non-condensing
Non-condensing
See mechanical drawing for location
UL 94V-0
Calculated per Mil Spec 27 E, or Bellcore at Ta=30ºC
Demonstrated
Min.
2250
0
-40
-40
0
Typ.
Max.
Units
V
DC
MΩ
ºC
ºC
%
ºC
x0
6
Hrs
x0
6
Hrs
25
85
90
30
2
.3
STANDARDS COMPLIANCE
Standards
UL/CSA 60950
Conditions
4
Basic insulation
MANUFACTURING TESTING
n
Burn-in test
n
Parametric test
SAFETY CONSIDERATIONS
This series of converters are certified to the standards and extent listed in the ‘Standards Compliance’ section in the table above. If this product is built into
information technology equipment, the installation must comply with the above standard. Even though the product is safety certified to operate without an input
fuse, it is recommended that an input fuse of 2A (max.) is used.
The output of the converter (Vo+/Vo-) is considered to remain within SELV limits when the input to the converter meets SELV or TNV-2 requirements. The
converters and materials meet UL 94V-0 flammability ratings.
RoHS COMPLIANCE
The EUS34-096 converter is in compliance with the European Union Directive 2002/95/EC (RoHS) with respect to the
following substances: lead (Pb), cadmium (Cd), mercury (Hg), hexavalent chromium, polybrominated biphenyls (PBB) and
polybrominated diphenyl ethers (PBDE).
For further information, please visit www.cd4power.com/rohs
2
3
4
V
IN
= 48Vdc, Ta = 25ºC, Airflow = 200 LFM for all data unless otherwise noted.
Input transient: if input voltage increases by 5V in µs, output over-current shut-down shall not be triggered (tested with Max. load and Max. output capacitance).
Thermal shutdown is monitored at the Thermal Measurement Location (TML). See ‘Mechanical Information’ on page 3 for TML location.
See ‘Safety Considerations’ shown on page 4.
Derating curves are conducted in a controlled environment. End application testing is required to ensure the Thermal Measurement Location temperature is below the maximum specified.
Recommended airflow direction is from pin to pin 3, or 3 to (transversal to the unit).
D C / D C
C O N V E R T E R S
CDC_EUS34-096.A04
Page 2 of 3
www.cd4power.com
Technical enquiries
email: toronto@cdtechno.com, tel: (866) 740 232
POWER ELECTRONICS DIVISION
EUS34-096
Isolated Bus Converter
PACKAGE SPECIFICATIONS
MECHANICAL DIMENSIONS
0.480
(12.19)
Max.
Ø0.040 ± 0.002 (1.02 ± 0.06)
(3X)
Ø0.062 ± 0.002 (1.57 ± 0.06)
(2X)
2.28 (57.9)
y
TML
0.300 (7.62)
PIN #4
0.90
(22.9)
PIN #5
Recommended
Footprint
Ø0.060 (1.52)
Ø0.105 (2.67)
Ø0.093 (2.36)
Ø0.137 (3.48)
0.300
(7.62)
0.45
(11.4)
PIN #3
PIN #2
PIN #1
0.300 (7.62)
0.14 (3.6)
2.000 (50.80)
Bottom view
0.300 (7.62)
Dimensions: 2.3 (58.4) L x .45 (36.83) W x 0.48 (2.9) H
京公网安备 11010802033920号
EEWORLD
