EEWORLDEEWORLDEEWORLD

Part Number

Search

X9317TP

Description
1K DIGITAL POTENTIOMETER, INCREMENT/DECREMENT CONTROL INTERFACE, 100 POSITIONS, PDSO8
Categorysemiconductor    logic   
File Size616KB,13 Pages
ManufacturerIntersil ( Renesas )
Websitehttp://www.intersil.com/cda/home/
Download Datasheet Parametric View All

X9317TP Overview

1K DIGITAL POTENTIOMETER, INCREMENT/DECREMENT CONTROL INTERFACE, 100 POSITIONS, PDSO8

X9317TP Parametric

Parameter NameAttribute value
Number of functions1
Number of terminals8
Maximum operating temperature85 Cel
Minimum operating temperature-40 Cel
Rated supply voltage2.7 V
Rated total resistance1000 ohm
Processing package descriptionROHS COMPLIANT, PLASTIC, SOIC-8
Lead-freeYes
EU RoHS regulationsYes
stateDISCONTINUED
CraftsmanshipCMOS
packaging shapeRECTANGULAR
Package SizeSMALL OUTLINE
surface mountYes
Terminal formGULL WING
Terminal spacing1.27 mm
terminal coatingMATTE TIN
Terminal locationDUAL
Packaging MaterialsPLASTIC/EPOXY
Temperature levelINDUSTRIAL
Type of converterDIGITAL POTENTIOMETER
ResistivityLINEAR
control interfaceINCREMENT/DECREMENT
Number of directions100
Maximum resistor tolerance20 %
Rated temperature coefficient300 ppm/Cel
Maximum terminal resistor voltage5.5 V
Minimum terminal resistor voltage0.0 V
DATASHEET
X9317
Low Noise, Low Power, 100 Taps, Digitally Controlled Potentiometer (XDCP™)
The Intersil X9317 is a digitally controlled potentiometer
(XDCP™). The device consists of a resistor array, wiper
switches, a control section, and nonvolatile memory. The wiper
position is controlled by a 3-wire interface.
The potentiometer is implemented by a resistor array
composed of 99 resistive elements and a wiper switching
network. Between each element and at either end are tap
points accessible to the wiper terminal. The position of the
wiper element is controlled by the CS, U/D, and INC inputs. The
position of the wiper can be stored in nonvolatile memory and
then be recalled upon a subsequent power-up operation.
The device can be used as a three-terminal potentiometer for
voltage control or as a two-terminal variable resistor for current
control in a wide variety of applications.
FN8183
Rev 9.00
November 4, 2014
Features
• Solid-state potentiometer
• 3-wire serial up/down interface
• 100 wiper tap points
- Wiper position stored in nonvolatile memory and recalled
on power-up
• 99 resistive elements
- Temperature compensated
- End-to-end resistance range ±20%
• Low power CMOS
- V
CC
= 2.7V to 5.5V, and 5V ±10%
- Standby current <5µA
• High reliability
- Endurance, 100,000 data changes per bit
- Register data retention, 100 years
• R
TOTAL
values = 10kΩ, 50kΩ, 100kΩ
• Packages
- 8 Ld SOIC, TSSOP, and MSOP
• Pb-free (RoHS compliant)
Applications
• LCD bias control
• DC bias adjustment
• Gain and offset trim
• Laser diode bias control
• Voltage regulator output control
U/D
V
CC
(SUPPLY VOLTAGE)
INC
CS
UP/DOWN
COUNTER
99
98
97
R
H
UP/DOWN
(U/D)
INCREMENT
(INC)
DEVICE SELECT
(CS)
CONTROL
AND
MEMORY
R
H
7-BIT
NONVOLATILE
MEMORY
R
W
R
L
STORE AND
RECALL
CONTROL
CIRCUITRY
96
ONE
OF
ONE
HUNDRED
DECODER
2
WIPER
SWITCHES
RESISTOR
ARRAY
V
SS
(GROUND)
GENERAL
V
CC
V
SS
1
0
R
L
R
W
DETAILED
FIGURE 1. BLOCK DIAGRAM
FN8183 Rev 9.00
November 4, 2014
Page 1 of 13
Help! Why does the chip get hot after power-on?
I developed a system using 5402. After power on, the DSP can be reset normally, but the external FLASH and power conversion chip TPS767D318 are hot. The chip has been tested and found to be short-circ...
monica150373637 Analogue and Mixed Signal
How to realize the communication between a gprs terminal and a pc?
How can I achieve communication between a GPRS terminal and a PC? I know that if I connect a GPRS module to a PC, it can be achieved. If the PC can access the Internet, can it communicate directly? Pl...
yushulei Embedded System
ARM latest information [C language embedded syntax]
C language embedded syntax...
呱呱 MCU
When does the EPWM counter of 28335 start counting?
When does the EPWM counter of 28335 start counting? If I initialize Epwm now, the value of counter TBCTR is cleared to 0, the values of compare registers CMPA and CMPB are cleared to 0, and the value ...
ShungChess Microcontroller MCU
Kinetis-K40FreeRTOS_V7.1.0 transplantation learning record
2012-3-6Refer to K60 in FreeRTOS_V7.1.01.Copy CORTEX_Kinetis_K60_Tower_IAR and rename it to CORTEX_Kinetis_K40X256_IAR;When opening the project, the compiler prompts that many header files cannot be f...
bluehacker NXP MCU
Why use 1117 voltage regulator instead of resistor voltage divider?
I searched on Baidu and found the following reasons which seem a bit confusing, so I would like to ask the experts in the forum: :time: Three reasons: 1. Power supply voltage. In actual applications, ...
ZNF PCB Design

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2532  1275  1873  940  2757  51  26  38  19  56 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号