SCOPE:
10V PRECISION VOLT REFERENCE
Device Type
01
Generic Number
MAX674M(x)/883B
Case Outline(s).
The case outlines shall be designated in Mil-Std-1835 and as follows:
Outline Letter
MAXIM SMD
TV
G
JA
P
LP
2
Mil-Std-1835
Case Outline
Package Code
G99
J8
L20
MACY1-X3
8 Lead TO-99 Can
GDIP1-T8 or CDIP2-T8 8 Lead CERDIP
CQCC3-N20
20 Leadless Chip
Absolute Maximum Ratings
Input Voltage ...........................................................................................….....…...... 40V
Output Short-circuit Duration (to GND or V
IN
) ....................................…........ Indefinite
Lead Temperature (soldering, 10 seconds) ....................................................….….... +300°C
Storage Temperature .............................................................................…... -65°C to +150°C
Continuous Power Dissipation ...................................................................…….....T
A
=+70°C
8-Pin TO-99 Can(derate 6.7mW/°C above +70°C) .............................................…... 533mW
8-Pin CERDIP(derate 8.0mW/°C above +70°C) ................................................…... 640mW
20 Pin Leadless Chip(derate 9.1mW/°C above +70°C) ......................................…... 727mW
Junction Temperature T
J
...................................................................................….. +150°C
Thermal Resistance, Junction to Case,
ΘJC:
8-Pin TO-99 Can .................................................................................... 45°C/W
8-Pin CERDIP ........................................................................................ 55°C/W
20-Pin LCC ............................................................................................ 20°C/W
Thermal Resistance, Junction to Ambient,
ΘJA:
8-Pin TO-99 Can ................................................................................... 150°C/W
8-Pin CERDIP ....................................................................................... 125°C/W
20-Pin LCC ........................................................................................... 110°C/W
Recommended Operating Conditions
Ambient Operating Range (T
A
) ............................................................. -55°C to
+125°C
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device.
These are stress ratings only, and functional operation of the device at these or any other conditions beyond
those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum
rating conditions for extended periods may affect device reliability.
----------------------------
Electrical Characteristics of MAX674/883B for
/883B and SMD 5962-94681
19-0262
Page 2 of
Rev. D
5
TABLE 1 ELECTRICAL TESTS
TEST
Symbol
CONDITIONS
-55
°C ≤T
A
≤
+125°C
V
IN
=+15V
Unless otherwise specified
Output Voltage
I
L
=0mA
Tolerance
Output Voltage
TCV
O
Change with
Temperature
Output Adjustment V
TRIM
RP=10kΩ
Range
Line Regulation
V
IN
=13V to 33V
NOTE 1
Load Regulation
Quiescent Supply
Current
Noise
Sink Current
Load Current
Short-circuit
Current
NOTE 1:
NOTE 2:
NOTE 3:
I
L
=0mA to 10mA
NOTE 1
Group A
Subgroup
Device
type
Limits
Min
Limits
Max
±15
20
Units
1,2,3
4,5,6
All
All
±300
mV
ppm/°C
1
1
2,3
1
2,3
1
2,3
4
1
1
2,3
1
All
All
All
All
All
All
All
All
mV
0.01
0.02
0.002
0.004
1400
2000
150
%/V
%/mA
µA
µVp-p
mA
mA
mA
I
Q
en p-p
I
S
I
L
I
SC
No Load
0.1Hz to 10Hz
NOTE 2
-0.3
10
8
40
NOTE 3
V
O
=0
Line and Load Regulation specifications include the effect of self heating.
Noise is sample tested.
Minimum Load Current is guaranteed by Load Regulation test.
PIN CONFIGURATION
PIN
J8/G99 L20
1
NC
NC
2
V
IN
NC
3
NC
NC
4
GND
NC
5
TRIM
V
IN
6
V
OUT
NC
7
NC
NC
8
NC
NC
9
NC
10
GND
L20
11
12
13
14
15
16
17
18
19
20
NC
TRIM
NC
NC
V
OUT
NC
NC
NC
NC
NC
ORDERING INFORMATION
Device
Package
Maxim Part Number
01
J8
MAX674MJA/883B
01
G99 Can
MAX674MTV/883B
01
LCC20
MAX674MLP/883B
SMD NUMBER
5962-9468102MPA
5962-9468102MGC
5962-9468102M2C
----------------------------
Electrical Characteristics of MAX674/883B
for /883B and SMD 5962-94681
19-0262
Page 3 of
Rev. D
5
QUALITY ASSURANCE
Sampling and inspection procedures shall be in accordance with MIL-Prf-38535, Appendix A as specified in Mil-Std-883.
Screening shall be in accordance with Method 5004 of Mil-Std-883. Burn-in test Method 1015:
1. Test Condition, A, B, C, or D.
2. TA = +125°C minimum.
3. Interim and final electrical test requirements shall be specified in Table 2.
Quality conformance inspection shall be in accordance with Method 5005 of Mil-Std-883, including Groups A, B, C, and D
inspection.
Group A inspection:
1. Tests as specified in Table 2.
2. Selected subgroups in Table 1, Method 5005 of Mil-Std-883 shall be omitted.
Group C and D inspections:
a. End-point electrical parameters shall be specified in Table 1.
b. Steady-state life test, Method 1005 of Mil-Std-883:
1. Test condition A, B, C, D.
2. TA = +125°C, minimum.
3. Test duration, 1000 hours, except as permitted by Method 1005 of Mil-Std-883.
TABLE 2.
ELECTRICAL TEST REQUIREMENTS
Mil-Std-883 Test Requirements
Subgroups
per Method 5005, Table 1
1
1*, 2, 3
1, 2, 3, 4
1
Interim Electric Parameters
Method 5004
Final Electrical Parameters
Method 5005
Group A Test Requirements
Method 5005
Group C and D End-Point Electrical Parameters
Method 5005
*
PDA applies to Subgroup 1 only.
----------------------------
Electrical Characteristics of MAX674/883B
for /883B and SMD 5962-94681
19-0262
Page 4 of
Rev. D
5
京公网安备 11010802033920号
EEWORLD
