Storage Ambient Temperature Range .................-55°C to +150°C
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
OPERATING CONDITIONS
PARAMETER
Operating Ambient Temperature
Bit Rate
CID Tolerance
SYMBOL
T
A
NRZ data
Consecutive identical digits
CONDITIONS
MIN
-40
1
TYP
+25
MAX
+125
12.5
100
UNITS
°C
Gbps
Bits
ELECTRICAL CHARACTERISTICS
(Specifications guaranteed over specified operating conditions. Typical values measured at T
A
= +25°C.)
PARAMETER
Supply Current
Input Swing
Compensation
Input Impedance
Output Impedance
Through Response
Input Return Loss
Output Return Loss
Resistance IN+ to IN- and OUT+
to OUT-
Resistance IN+ to OUT+ and
IN- to OUT-
Resistance IN+ to OUT- and
IN- to OUT+
DC Gain (OUT/IN)
Residual Deterministic Jitter
(Table 1, Notes 1, 2)
Measured differentially at point A in Figure 1
5GHz relative to 100MHz
Differential, Z
LOAD
= 100Ω
Differential, Z
SOURCE
= 100Ω
Relative to ideal load, see Figure 2 for setup
100MHz to 6GHz
100MHz to 6GHz
No load, high impedance on all ports
No load, high impedance on all ports
No load, high impedance on all ports
Z
LOAD
= 100Ω
3.125Gbps and 6.25Gbps, 18in of 6mil
microstrip FR4
8.5Gbps, 10.0Gbps, and 12.5Gbps,
18in of 6mil microstrip FR4
112
32
112
0.5
0.05
UI
0.10
6
100
100
See Figure 3 for limits
15
15
152
44
152
dB
dB
Ω
Ω
Ω
SYMBOL
CONDITIONS
MIN
TYP
0.0
3600
MAX
UNITS
mA
mV
P-P
dB
Ω
Ω
Note 1:
Signal applied differentially at point A as shown in Figure 1. The deterministic jitter at point B is from media-induced loss,
not from clock-source modulation. Deterministic jitter is measured at the 50% vertical level of the signal at point C.
Note 2:
Difference in deterministic jitter between reference points A and C in Figure 1. Stress pattern: 2
[i=s] This post was last edited by qq849682862 on 2014-11-4 08:21 [/i] I just downloaded a document about WIFI technology principle from Beiyou Continuing Education College from the document library. ...
[Abstract] This paper introduces the communication solution of AGV (Automated Guided Vehicle) in industrial automatic logistics. It briefly introduces the integration of wireless data communication an...
When the capacitance is very small, theoretically the time constant of this circuit is very small and the circuit transition process is very short. Why does the simulation result show oscillation and ...
Assume that data is read from 8-bit AD (if it is a higher-bit AD, the data type can be defined as int), the subroutine is get_ad();
1. Limited secondary filtering
/* A value can be adjust...[Details]
In early 2002, I started to write a working program for an IC card prepaid electricity meter. The meter used Philips' 8-bit 51-expanded single-chip microcomputer
87LPC764
, and wa...[Details]
With the rapid development of science and technology, especially the widespread application of digital technology and various ultra-large-scale integrated circuits, electronic equipment, especially...[Details]
Floating-point digital signal processing has become a constant requirement for precision technology, often in applications requiring high accuracy in areas such as aviation, industrial machinery, a...[Details]
1 Introduction
Solar street lights are mainly composed of four parts: solar photovoltaic cell components, batteries, charge and discharge controllers, and lighting fixtures. The bo...[Details]
From the PIC16F946 datasheet, we know that there are two ways to write values to the LCD for display:
1. Directly write the value to LCDDATA1~LCDDATA23
2. Use disconnect t...[Details]
1 Introduction
There have been many studies on the detection and protection of power grid short circuit and line fault. The short circuit, overload and overvoltage protectors on the market have ...[Details]
Overview
In spectral measurement, photomultiplier tubes (PMT) and charge-coupled devices (CCD) are often used as photoelectric converters. PMT is used in slow-changing, high-precision spectral...[Details]
Single-chip microcomputers are widely used because of their small size, powerful functions and low price. This article introduces the method of designing a micro electronic piano using the AT89C51 sin...[Details]
introduction
MAX6636 is a multi-channel precision temperature monitor that can not only monitor local temperature, but also connect up to 6 diodes externally. Each channel has a programmable...[Details]
With the rapid development of wireless
digital communication
, more challenges have been raised for integrated circuit design and testing. In the product design stage, in order to ensure
t...[Details]
The launch of Shenzhou IX is imminent, and Tiangong is welcoming visitors again. Yesterday, Professor Fu Qiang, Vice President of the Institute of Science and Industrial Technology of Harbin Instit...[Details]
With the rapid development of the national economy, lifting and hoisting operations are used more and more frequently and widely in various fields of economic construction. China has continuously expl...[Details]
1 What is an LED floodlight?
LED downlights are also called spotlights, projection lamps, and spotlights. They are mainly used for architectural decorative lighting and commercial space lighti...[Details]
IntroductionLED
billboards are a kind of information display terminal for the public, which has a wide range of civil and commercial values. However, the information displayed on most LED bil...[Details]
stm32/stm8
京公网安备 11010802033920号
EEWORLD
