Dear experts, I used to work on the 51 series, but recently I took on a project developed using 430. After studying for a few days, I still don't understand how to write programs into the microcontrol...
Today I built a resistor. A 20M ohm resistor was connected to 3V, and then a 50M ohm resistor was connected to ground for voltage division. The voltage was then followed and output to the microcontrol...
[i=s]This post was last edited by jameswangsynnex on 2015-3-3 19:51[/i] First, prepare the materials: 1. A discarded 4-wire headset 2. A light touch button. Prepare the materials and start working!1. ...
1 Efficiency and power factor of electric motor
1.1 Efficiency of electric motor
Efficiency = × 100% = × 100%
In actual use, the efficiency of the motor also includes rated efficiency, maximum efficie...
I picked up a piece of code from a book, which is used to assign values to a new database record, but there is an error: bool CDataBaseTestDlg::AddNewStudent(REC_STUDENT stu) { CEOID ceOid; CEPROPVAL ...
For STM32, there are two ways to reset the software: 1) Use the official software library The system reset function is directly provided in the stm32f10x_nvic.c file of the official software li...[Details]
Security PPP is a new model of urban video surveillance projects: 1) The government and social capital establish a project company in a certain proportion; 2) The project company participates in the ...[Details]
When designing a product, if the application environment's requirements for power isolation are not considered, the product will be unstable due to improper design, and even high voltage may damage t...[Details]
This program uses the eight-channel ADC single acquisition mode. According to the configuration, ADC12SC will automatically reset after the conversion is completed in the single mode, so it is necess...[Details]
This paper combines embedded control technology with network control technology to realize the design of temperature control system based on single chip microcomputer through Internet control. Th...[Details]
Kevin Jensen ams Semiconductor
Sensors
and lighting expert. Let's learn more about the relevant content with the network communication editor.
Everything is becoming "smart" these ...[Details]
In order to strengthen the traceability management of recycling and utilization of power batteries for new energy vehicles, and to standardize and guide all relevant parties to fulfill their tracea...[Details]
Summary of STM32 peripheral DMA usage: 1. Select DAM mode according to your needs: (1) Circular mode—DMA_Mode = DMA_Mode_Circular (2) Normal mode—DMA_Mode = DMA_Mode_Normal 2. For Chanel3 of DMA1, t...[Details]
1. Common knowledge about DMA. 1. Function: to achieve high-speed data transmission between chips. That is, it can achieve data transmission without occupying the CPU. 2. Mode: There are three tran...[Details]
12864 LCD parallel port driver is more commonly used, but considering that sometimes the IO port of the microcontroller or MCU is limited, the serial driver method can be used. The following is ...[Details]
This program sets the LED running light and the 0-16 numbers of the 0th position of the digital tube to light up in a cycle. The digital tube program cannot be put into the main function, because the...[Details]
Title: Use the table lookup method to convert a hexadecimal number into ASCII code. The input parameter is placed in the internal RAM 50H, and the output parameter is in R0. Requirements: Complete th...[Details]
Title: Use two dynamic digital tubes to display from 0 to 60, output from the P1 port of 89C51, without adding a decoder, and directly connect the digital tubes. Note that they are dynamic digital tu...[Details]
//Environment: winavr+avr studio char temp=0; ISR(TIMER1_COMPA_vect )//interrupt function { // user code here temp++; if (temp==10) temp=0; PORTA=temp; DDRA=0xff; } void ...[Details]
Microcontroller MCU
京公网安备 11010802033920号
EEWORLD
