EEWORLDEEWORLDEEWORLD

Part Number

Search

PH1-GLHSA3641

Description
Transponder, 10000Mbps(Tx), 10000Mbps(Rx), SC/UPC Connector,
CategoryWireless rf/communication    Optical fiber   
File Size240KB,6 Pages
ManufacturerLumentum Operations LLC
Download Datasheet Parametric View All

PH1-GLHSA3641 Overview

Transponder, 10000Mbps(Tx), 10000Mbps(Rx), SC/UPC Connector,

PH1-GLHSA3641 Parametric

Parameter NameAttribute value
MakerLumentum Operations LLC
Reach Compliance Codecompliant
Other featuresIT ALSO OPERATE FROM 1280NM TO 1600NM
body width56.1 mm
body height13.2 mm
Body length or diameter76.5 mm
Connection TypeSC/UPC CONNECTOR
Data rate (receive)10000 Mbps
Data rate (send)10000 Mbps
Emitter/Detector TypeAVALANCHE PHOTODIODE
Fiber optic equipment typesTRANSCEIVER, TRANSPONDER
Nominal operating wavelength1549 nm
Nominal optical power output2.511 mW
minimum return loss-27 dB
Sensitivity-24 dBm
COMMUNICATIONS MODULES & SUBSYSTEMS
10 Gb/s TDM/DWDM 300 Pin SFF MSA SR2/IR2/LR2 Transponder
PH1 Series
Key Features
• Three configurations supporting SR2/IR2/LR2 applications
• Supports dense wavelength division multiplexing
(DWDM) applications (without wavelocker)
• Microprocessor controls to support I2C
• Integrated 16:1/1:16 mux/demux
• Small form factor package (2.2" x 3.0" x 0.53") for high
density applications
• Low power consumption: 4.8 W typical, 6.8 W maximum
for TDM applications
• 70 °C maximum operating temperature
• High sensitivity PIN or APD receivers
• SONET, FEC, Ethernet and Multirate Capable Versions
• Forward, counter and line timing clocking modes
Applications
Telecommunications
Metropolitan Area Networks
Subscriber loop
Intra-office SONET/SDH
High bit-rate data communications
JDSU 10 Gb/s PH1 Series transponders are intended for 1550 nm system
applications with reaches of up to 80 km. The series includes three different
transponders for SR2 (25 km), IR2 (40 km), and LR2 (80 km) TDM or DWDM
applications. Each transponder accepts 16 bits of parallel digital data and converts
it to a 10 Gb/s NRZ modulated optical signal. It also accepts a 10 Gb/s NRZ
modulated optical signal and converts it into 16 bit wide parallel digital data.
The PH1 series offers low DC power dissipation and is available in either a small
form factor package (2.2 x 3 x 0.53 inches) or in a larger footprint (3.5 x 4.5 x 0.53
inches) package, depending on system thermal performance requirements. The
transmit design uses an Electro-Absorptive Modulated Laser (EML) which,
depending on the configuration, produces an average output power of between
-4 dBm to 2 dBm (EOL). A PIN (-17 dBm typical sensitivity) or APD (-24 dBm
typical sensitivity) receiver is available, based on system configurations.
JDSU PH1 Series transponders are designed to support the following data rates:
9.953 Gb/s (SONET), 10.3125 Gb/s (Ethernet), 10.664 Gb/s (FEC Encoded),
10.709 Gb/s FEC, or 11.09 Gb/s EFEC. They meet all applicable SONET/SDH standards.
Compliance
• Telcordia GR-253-Core
NORTH AMERICA
:
800 498-JDSU (5378)
WORLDWIDE
:
+800 5378-JDSU
WEBSITE
:
www.jdsu.com
RFID open access control system application 2
RFID open access control system application 2...
xtss RF/Wirelessly
MEMS Technology
MEMS is the abbreviation of MicroElectroMechanicalsystems, i.e. micro-electromechanical systems. Micro-electromechanical systems (MEMS) technology is a cutting-edge technology in the 21st century base...
xuxuhuen Sensor
Msp430f149 programming problem
I have used two programming softwares, mspfet and fet-pro430, to program f149 via USB emulator and JTAG protocol, but both failed. I suspect it is a problem of setting and operation. Can you please te...
chenminjie Microcontroller MCU
How to record the number of boot times of 2051 microcontroller
How to record the number of times 2051 is powered on? Each time it is powered on, add 1. When the specified number of times is reached, the program will not run. It would be best if you can provide a ...
15011460232 51mcu
Has anyone done 6410 pwm?
I set 28 and 29 in GPFCON to TOUT0 function TCFG0 0x101 TCFG1 default 0 TCNTB0=2070 TCMPB0=2070/2 TCON 0x XXXXXXX9 XXXXXXXb All registers are set successfully. (I printed it out to see) But there is n...
qu27jump Embedded System
In Keil, there must be one project file (target) corresponding to one source group, and one source group corresponding to one C file?
In Keil, there must be one project file (target) corresponding to one source group, and one source group corresponding to one C file?...
QWE4562009 Integrated technical exchanges

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2326  2767  2706  2213  1653  47  56  55  45  34 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号