PH1-GLHSA3165 datasheet, PDF - EEWORLD Datasheet

Datasheet> All Categories > Wireless rf/communication> Optical fiber> PH1-GLHSA3165

PH1-GLHSA3165: DescriptionTransponder, 10000Mbps(Tx), 10000Mbps(Rx), SC/UPC Connector,; CategoryWireless rf/communication Optical fiber; File Size240KB，6 Pages; ManufacturerJDS Uniphase Corporation ( VIAVI ); Websitehttp://www.jdsu.com/index.html

Download Datasheet Parametric View All

PH1-GLHSA3165 Overview

Transponder, 10000Mbps(Tx), 10000Mbps(Rx), SC/UPC Connector,

PH1-GLHSA3165 Parametric

Parameter Name	Attribute value
Maker	JDS Uniphase Corporation ( VIAVI )
Reach Compliance Code	unknown
Other features	IT ALSO OPERATE FROM 1280NM TO 1600NM
body width	56.1 mm
body height	13.2 mm
Body length or diameter	76.5 mm
Connection Type	SC/UPC CONNECTOR
Data rate (receive)	10000 Mbps
Data rate (send)	10000 Mbps
Emitter/Detector Type	AVALANCHE PHOTODIODE
Fiber optic equipment types	TRANSCEIVER, TRANSPONDER
Nominal operating wavelength	1540 nm
Nominal optical power output	2.511 mW
minimum return loss	-27 dB
Sensitivity	-24 dBm

Preview

Download Datasheet

View All

COMMUNICATIONS MODULES & SUBSYSTEMS

10 Gb/s TDM/DWDM 300 Pin SFF MSA SR2/IR2/LR2 Transponder

PH1 Series

Key Features

• Three configurations supporting SR2/IR2/LR2 applications

• Supports dense wavelength division multiplexing

(DWDM) applications (without wavelocker)

• Microprocessor controls to support I2C

• Integrated 16:1/1:16 mux/demux

• Small form factor package (2.2" x 3.0" x 0.53") for high

density applications

• Low power consumption: 4.8 W typical, 6.8 W maximum

for TDM applications

• 70 °C maximum operating temperature

• High sensitivity PIN or APD receivers

• SONET, FEC, Ethernet and Multirate Capable Versions

• Forward, counter and line timing clocking modes

Applications

•

Telecommunications

Metropolitan Area Networks

Subscriber loop

Intra-office SONET/SDH

High bit-rate data communications

JDSU 10 Gb/s PH1 Series transponders are intended for 1550 nm system

applications with reaches of up to 80 km. The series includes three different

transponders for SR2 (25 km), IR2 (40 km), and LR2 (80 km) TDM or DWDM

applications. Each transponder accepts 16 bits of parallel digital data and converts

it to a 10 Gb/s NRZ modulated optical signal. It also accepts a 10 Gb/s NRZ

modulated optical signal and converts it into 16 bit wide parallel digital data.

The PH1 series offers low DC power dissipation and is available in either a small

form factor package (2.2 x 3 x 0.53 inches) or in a larger footprint (3.5 x 4.5 x 0.53

inches) package, depending on system thermal performance requirements. The

transmit design uses an Electro-Absorptive Modulated Laser (EML) which,

depending on the configuration, produces an average output power of between

-4 dBm to 2 dBm (EOL). A PIN (-17 dBm typical sensitivity) or APD (-24 dBm

typical sensitivity) receiver is available, based on system configurations.

JDSU PH1 Series transponders are designed to support the following data rates:

9.953 Gb/s (SONET), 10.3125 Gb/s (Ethernet), 10.664 Gb/s (FEC Encoded),

10.709 Gb/s FEC, or 11.09 Gb/s EFEC. They meet all applicable SONET/SDH standards.

Compliance

• Telcordia GR-253-Core

NORTH AMERICA

800 498-JDSU (5378)

WORLDWIDE

+800 5378-JDSU

WEBSITE

www.jdsu.com

Recommended Resources

Those classic analog circuits worth collecting

HT-1350 circuit

Variable frequency high frequency LC oscillator circuit

Gongtai GT-JDG3 motor protector typical application circuit

CA3080 variable gain amplifier circuit

Timer circuit using monostable generator

Question: How does Windows know that the power button has been pressed?: Windows XP can shut down (shut down the system) safely by pressing the power button, but Windows 2000 Server only has "power off", "hibernate" and "standby". I want to shut down Windows 2000 Server sa...; bbyyjjj Embedded System

GD32L233C-START Development Board Study Notes (Part 2): [i=s]This post was last edited by wxd123com on 2022-1-28 17:23[/i]GD32L233C-START Development Board Study Notes ( Part 2) 1. Firmware The file organization structure in the GD32L23x_Firmware_Lbirary f...; wxd123com GD32 MCU

How to load program into ARM via CAN bus?: I am currently working on a board with an ARM chip and CAN bus communication. When debugging, I always use JTAG or the serial port to load the program .hex file. However, after installing it in the de...; tianpuf ARM Technology

Future Trends of 3D Chips: [i=s]This post was last edited by jameswangsynnex on 2015-3-3 19:58[/i] [font=宋体][size=9pt][color=#000000] I saw a piece of news and would like to share it with you. [/color][/size][/font][font=Arial]...; jameswangsynnex Mobile and portable

Confused, seeking help: Hello everyone! I am a sophomore student in college. I am very interested in embedded systems, but I don't know where to start. In high school, I was very interested in mathematics and physics, and le...; zpr510 Embedded System

[Serial] [ALIENTEK Battleship STM32 Development Board] STM32 Development Guide--Chapter 42 External SRAM Experiment: [color=rgb(0,0,0)][backcolor=rgb(255,255,255)][b][color=#000000]Chapter 42[/color] External SRAM Experiment[/b][align=left][b] [/b]STM32F103ZET6 comes with 64K bytes of SRAM, which is enough for gener...; 正点原子 stm32/stm8

Shortcut: L0 L1 L2 L3 L4 L5 L6 L7 L8 L9 LA LB LC LD LE LF LG LH LI LJ LK LL LM LN LO LP LQ LR LS LT LU LV LW LX LY LZ M0 M1 M2 M3 M4 M5 M6 M7 M8 M9 MA MB MC MD ME MF MG MH MI MJ MK ML MM MN MO MP MQ MR MS MT MU MV MW MX MY MZ N0 N1 N2 N3 N4 N5 N6 N7 N8 NA NB NC ND NE NF NG NH NI NJ NK NL NM NN NO NP NQ NR NS NT NU NV NX NZ O0 O1 O2 O3 OA OB OC OD OE OF OG OH OI OJ OK OL OM ON OP OQ OR OS OT OV OX OY OZ P0 P1 P2 P3 P4 P5 P6 P7 P8 P9 PA PB PC PD PE PF PG PH PI PJ PK PL PM PN PO PP PQ PR PS PT PU PV PW PX PY PZ Q1 Q2 Q3 Q4 Q5 Q6 Q8 Q9 QA QB QC QE QF QG QH QK QL QM QP QR QS QT QV QW QX QY R0 R1 R2 R3 R4 R5 R6 R7 R8 R9 RA RB RC RD RE RF RG RH RI RJ RK RL RM RN RO RP RQ RR RS RT RU RV RW RX RY RZ

Popular Components