EEWORLDEEWORLDEEWORLD

Part Number

Search

X40010S8-B

Description
16 Characters x 2 Lines, 5x7 Dot Matrix Character and Cursor
File Size127KB,25 Pages
ManufacturerXicon Passive Components
Websitehttp://www.xicor.com
Download Datasheet View All

X40010S8-B Overview

16 Characters x 2 Lines, 5x7 Dot Matrix Character and Cursor

New Features
• Monitor Voltages: 5V to 0.9V
• Independent Core Voltage Monitor
Preliminary Datasheet
X40010/X40011/X40014/X40015
Dual Voltage Monitor with Integrated CPU Supervisor
FEATURES
• Dual voltage detection and reset assertion
—Standard reset threshold settings
See Selection table on page 2.
—Adjust low voltage reset threshold voltages
using special programming sequence
—Reset signal valid to V
CC
= 1V
—Monitor three voltages or detect power fail
• Independent Core Voltage Monitor (V2MON)
• Fault detection register
• Selectable power on reset timeout (0.05s,
0.2s, 0.4s, 0.8s)
• Selectable watchdog timer interval (25ms, 200ms,
1.4s, off)
• Low power CMOS
—25µA typical standby current, watchdog on
—6µA typical standby current, watchdog off
• 400kHz 2-wire interface
• 2.7V to 5.5V power supply operation
• Available packages
—8-lead SOIC, TSSOP
APPLICATIONS
• Communication Equipment
—Routers, Hubs, Switches
—Disk Arrays, Network Storage
• Industrial Systems
—Process Control
—Intelligent Instrumentation
• Computer Systems
—Computers
—Network Servers
DESCRIPTION
The X40010/11/14/15 combines power-on reset con-
trol, watchdog timer, supply voltage supervision, and
secondary voltage supervision, in one package. This
combination lowers system cost, reduces board space
requirements, and increases reliability.
Applying voltage to V
CC
activates the power on reset
circuit which holds RESET/RESET active for a period of
time. This allows the power supply and system oscillator
to stabilize before the processor can execute code.
Low V
CC
detection circuitry protects the user’s system
from low voltage conditions, resetting the system when
V
CC
falls below the minimum V
TRIP1
point. RESET/
RESET is active until V
CC
returns to proper operating
level and stabilizes. A second voltage monitor circuit
tracks the unregulated supply to provide a power fail
warning or monitors different power supply voltage.
Three common low voltage combinations are avail-
able, however, Xicor’s unique circuits allows the
BLOCK DIAGRAM
Watchdog Timer
and
Reset Logic
SDA
Data
Register
Command
Decode Test
& Control
Logic
Threshold
Reset Logic
Fault Detection
Register
Status
Register
WDO
SCL
V
CC
(V1MON)
+
User Programmable
V
TRIP1
User Programmable
V
TRIP2
-
+
-
V2MON
V
CC
Power on,
Low Voltage
Reset
Generation
RESET
X40010/14
RESET
X40011/15
V2MON
V2FAIL
*X40010/11 = V2MON*
X40014/15 = V
CC
REV 1.3.4 7/12/02
www.xicor.com
Characteristics subject to change without notice.
1 of 25
Fundamentals of FPGA Design and Implementation of Digital Circuits
Hehe, I recently did a simulation of a digital circuit. Can you give me some advice? It will help me further my study!...
lvfanzai FPGA/CPLD
How to use hex 80 in MSP430 bootloader (BSL) communication
[size=4] Hex 80 is sent as a sync character before each transmission. The device acknowledges with hex 90. The data frame is then sent. Each frame begins with a header byte = hex 80. The other bytes o...
Aguilera Microcontroller MCU
How to put LM3S9B96 functions into RAM and run them?
I wrote an algorithm function using LM3S9B96 and downloaded it to the on-chip Flash. The execution time is 35us, which is far from the design goal. How can I put this function into RAM to run? When th...
jipanpan Microcontroller MCU
Knowledge points of 51 single chip microcomputer
[align=left]1. The P0 port of 51 single-chip microcomputer is very special. 2. The operation of 51 single-chip microcomputer is essentially the operation of registers, and the same is true for other s...
QQ2848218839 51mcu
10 Tips for Embedded Software Testing
Many years ago, a developer, seeking a deeper understanding of embedded systems, asked this question: How can I know and understand what my system is doing? I was a little surprised by this question b...
xyd18025265652 Programming Basics
How to measure the voltage across a diode
As shown in the figure, the D15 diode at the secondary end of the switching power supply has its open measurement waveform as shown below, green is the current, and orange is the voltage: At the momen...
陈陈陈1 Analog electronics

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2233  802  218  2889  1990  45  17  5  59  41 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号