MFL283R3S datasheet, PDF - EEWORLD Datasheet

Datasheet> All Categories > Analog mixed-signal IC> The signal circuit> MFL283R3S

MFL283R3S: Description1-OUTPUT 40 W DC-DC REG PWR SUPPLY MODULE; CategoryAnalog mixed-signal IC The signal circuit; File Size588KB，13 Pages; ManufacturerInterpoint （ Crane Aerospace & Electronics ）; Websitehttp://www.interpoint.com

Download Datasheet Parametric Compare View All

MFL283R3S Overview

1-OUTPUT 40 W DC-DC REG PWR SUPPLY MODULE

MFL283R3S Parametric

Parameter Name	Attribute value
Maker	Interpoint （ Crane Aerospace & Electronics ）
Parts packaging code	MODULE
package instruction	,
Contacts	12
Reach Compliance Code	unknow

Preview

Download Datasheet

View All

Crane Aerospace & Electronics Power Solutions

MFL single and dual dc/dc converters

28 VoLt input – 65 Watt

Features

Parallel operation with current share,

up to 3 units (148 watts)

• -55° to +125°C operation

• 16 to 40 VDC input

VDc O

utPut

single

MODELS

• 50 V for 120 ms transient protection

• Fully isolated, magnetic feedback

• Fixed high frequency switching

• Remote sense or output trim on

single output models

• Inhibit function

• Sync in and Sync Out

3.3

Dual

±5

±12

±15

• Indefinite short circuit protection

Other output voltages

available upon request,

including 2 V, 8 V and

54 V single.

• High power density, 87% efficiency

description

The MFL Series™ 28-volt DC/DC converters are rated up to 65

watts of output power over a -55°C to +125°C temperature range

with a 28 VDC nominal input. On dual output models up to 70%

of the rated output power can be drawn from either the positive

or negative output. Current sharing allows the units to be paral-

leled for total power of up to 148 watts. The welded, hermetically

sealed package is only 3.005 x 1.505 x 0.400 inches, giving

the series an overall power density of up to 43 watts per cubic

inch. The converters are offered with standard screening, “ES”

screening, or fully compliant to “883” MIL-PRF-38534 Class H

screening. Standard microcircuit drawings (SMD) are available.

nhibit

The MFL Series converters have two inhibit terminals (INH1 and

INH2) that can be used to disable power conversion, resulting in

a very low quiescent input current and no generation of switching

noise. A logic low (<0.8 volts) is required to inhibit the converter

between INH1 (pin 4) and Input Common (pin 2). A logic low

(<0.5 volts) is required to inhibit the converter between INH2 (pin

12) and Output Common (pin 8). The application of intermediate

voltages to these pins (1.5 to 10.5 volts) should be avoided.

ync

esign

eatures

The MFL Series converters are switching regulators that use a

quasi-square wave, single ended forward converter design with a

constant switching frequency of 600 kHz.

Isolation between input and output circuits is provided with a

transformer in the forward path and a wide bandwidth magnetic

coupling in the feedback control loop. The MFL uses a unique

dual loop feedback technique that controls output current with

an inner feedback loop and an output voltage with a cascaded

voltage mode feedback loop.

The additional secondary current mode feedback loop improves

transient response in a manner similar to primary current mode

control and allows for ease of paralleling, but without the cost

and complexity.

The constant frequency, pulse-width modulated converters use a

quasi-square wave single-ended forward design. Tight load regu-

lation is achieved through a wide-bandwidth magnetic feedback

circuit. The output on single MFL models can be trimmed (see

Figure 1 for voltage changes with different resistor values).

Crane Aerospace & Electronics

Electronics Group (Interpoint Brand)

PO Box 97005 • Redmond WA 98073-9705

425.882.3100 • power@crane-eg.com

www.craneae.com/interpoint

Converters may be synced to an external clock (525 to 675 kHz)

or to one another by using the sync in or out pins. The nominal

free-run switching frequency is 600 kHz (see Application Note on

Inhibit and Synchronization).

urrent anD

arallel

PeratiOn

Multiple MFL converters may be used in parallel to drive a

common load (see Figure 2). In this mode of operation the load

current is shared by two or three MFL converters. In current

sharing mode, one MFL converter is designated as a master.

The SLAVE pin (pin 11) of the master is left unconnected and

the MSTR/INH2 pin (pin 12) of the master is connected to the

SLAVE pin (pin 11) of the slave units. The units designated as

slaves have the MSTR/INH2 pin (pin 12) connected to the SNS

RTN pin (pin 9). Figure 2 shows the typical setup for two or

three units in parallel. Note that synchronizing the units together

(though shown in the figure) is not required for current sharing

operation. A second slave unit may be placed in parallel with a

master and slave; this requires the TRI pin (pin 3) of the master

unit to be connected to the SNS RTN pin (pin 9).

When paralleled, 76% of the total combined power ratings of the

MFL converters are available at the load. Overload and short

circuit performance are not adversely affected during parallel

operation

Page 1 of 13

MFL Rev E - 20101026

MFL283R3S Related Products

	MFL283R3S	5962-9319301hxc	MFL2815D	MFL283R3S_10
Description	1-OUTPUT 40 W DC-DC REG PWR SUPPLY MODULE	Single, Dual, Quad, 1.2µA Max, Single-Supply Op Amps	Single, Dual, Quad, 1.2µA Max, Single-Supply Op Amps	Single, Dual, Quad, 1.2µA Max, Single-Supply Op Amps
Maker	Interpoint （ Crane Aerospace & Electronics ）	Interpoint （ Crane Aerospace & Electronics ）	Interpoint （ Crane Aerospace & Electronics ）	-
Parts packaging code	MODULE	MODULE	MODULE	-
Contacts	12	12	12	-
Reach Compliance Code	unknow	unknow	unknow	-

Recommended Resources

Half-wave capacitor step-down rectifier circuit b

The simplest one-way thyristor dimming light circuit

High sensitivity acoustic vibration alarm circuit

Actual circuit consisting of TDAll90

Application circuit design of Fuji IGBT smart module

SAMD20 IAR project download error: Error when downloading IAR program using USB on SAMD20...; 风海蓝天 Microchip MCU

Calculation Problems of Active Filters: Experts, the attachment is a differential filter circuit made of OPA1632, which is mainly used to filter the noise of the audio part. The bandwidth is 14.5-33kHz. We can know 14.5 Hz, but I don’t know...; willing_chen Analog electronics

Passthru Problem: I am confused again, so I will describe the problem. First, encrypt all TCP packets sent to a certain address in MPSENDPACKETS, and modify the checksum. Then perform reverse decryption in PTRECEIVE, a...; 汪园园 Embedded System

Help with LwIP operating system transplantation, compilation and linking issues!: There is no problem in compiling, but there are several problems in linking as follows: .\Object\ucos_lwip.axf: Error: L6406E: No space in execution regions with .ANY selector matching rit128x96x4.o(....; 186874509 Microcontroller MCU

Factors affecting the characteristic impedance of printed circuit boards (PCBs) and their countermeasures: Factors affecting the characteristic impedance of printed circuit boards (PCBs) and their countermeasures...; fighting PCB Design

"Play with pyboardCN V2" 1 Install the driver and serial port assistant to light up 4 lights: [i=s]This post was last edited by damiaa on 2018-6-25 09:18[/i] "Play with pyboardCN V2" Part 1 Install the driver and serial port assistant to light up the four lights 1. Install PUTTY or Tera Term V...; damiaa MicroPython Open Source section

Shortcut: A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 AA AB AC AD AE AF AG AH AI AJ AK AL AM AN AO AP AQ AR AS AT AU AV AW AX AY AZ B0 B1 B2 B3 B4 B5 B6 B7 B8 B9 BA BB BC BD BE BF BG BH BI BJ BK BL BM BN BO BP BQ BR BS BT BU BV BW BX BY BZ C0 C1 C2 C3 C4 C5 C6 C7 C8 C9 CA CB CC CD CE CF CG CH CI CJ CK CL CM CN CO CP CQ CR CS CT CU CV CW CX CY CZ D0 D1 D2 D3 D4 D5 D6 D7 D8 D9 DA DB DC DD DE DF DG DH DI DJ DK DL DM DN DO DP DQ DR DS DT DU DV DW DX DZ

Popular Components