EEWORLDEEWORLDEEWORLD

Part Number

Search

ISL45041IRZ-T7

Description
SPECIALTY CONSUMER CIRCUIT, PDSO8, 3 X 3 MM, 0.80 MM HEIGHT, ROHS COMPLIANT, PLASTIC, MO-229WEEC-2, TDFN-8
CategoryOther integrated circuit (IC)    Consumption circuit   
File Size294KB,8 Pages
ManufacturerRenesas Electronics Corporation
Websitehttps://www.renesas.com/
Environmental Compliance
Download Datasheet Parametric View All

ISL45041IRZ-T7 Overview

SPECIALTY CONSUMER CIRCUIT, PDSO8, 3 X 3 MM, 0.80 MM HEIGHT, ROHS COMPLIANT, PLASTIC, MO-229WEEC-2, TDFN-8

ISL45041IRZ-T7 Parametric

Parameter NameAttribute value
Is it Rohs certified?conform to
MakerRenesas Electronics Corporation
package instructionHVSON,
Reach Compliance Codecompliant
Other featuresALSO REQUIRES 2.6 TO 3.6 V
Commercial integrated circuit typesCONSUMER CIRCUIT
JESD-30 codeS-PDSO-N8
JESD-609 codee3
length3 mm
Humidity sensitivity level1
Number of functions1
Number of terminals8
Maximum operating temperature85 °C
Minimum operating temperature
Package body materialPLASTIC/EPOXY
encapsulated codeHVSON
Package shapeSQUARE
Package formSMALL OUTLINE, HEAT SINK/SLUG, VERY THIN PROFILE
Peak Reflow Temperature (Celsius)260
Maximum seat height0.8 mm
Maximum supply voltage (Vsup)18 V
Minimum supply voltage (Vsup)10.8 V
surface mountYES
Temperature levelOTHER
Terminal surfaceMatte Tin (Sn) - annealed
Terminal formNO LEAD
Terminal pitch0.65 mm
Terminal locationDUAL
Maximum time at peak reflow temperature30
width3 mm
DATASHEET
TFT-LCD I
2
C Programmable VCOM Calibrator
ISL45041
The V
COM
voltage of an LCD panel needs to be adjusted to
remove flicker. The ISL45041 part provides a digital interface
to control the sink current output that attaches to an external
voltage divider. The increase in output sink current lowers the
voltage on the external divider, which is applied to an external
V
COM
buffer amplifier. The desired V
COM
setting is loaded from
an external source via a standard 2-wire I
2
C serial interface. At
power-up, the part automatically comes up at the last
programmed EEPROM setting.
An external resistor attaches to the SET pin and sets the
full-scale sink current that determines the lowest voltage of
the external voltage divider.
The ISL45041 is available in an 8 Ld 3mmx3mm TDFN
package with a maximum thickness of 0.8mm for ultra thin
LCD panel design.
An evaluation kit complete with software to control the DCP
from a computer is available. Reference Application Note
AN1275
and “Ordering Information” on
page 2.
Features
• 128-step adjustable sink current output
• 2.25V to 3.6V logic supply voltage operating range (2.6V
minimum programming voltage)
• 4.5V to 18V analog supply voltage operating range (10.8V
minimum programming voltage)
• I
2
C interface with addresses 100111x and 100110x
• On-chip 7-Bit EEPROM
• Output adjustment SET pin
• Output guaranteed monotonic over-temperature
• Thin 8 Ld 3mmx3mm DFN (0.8mm max)
• Pb-free (RoHS compliant)
Applications
• LCD panels
Related Literature
AN1208
“LCD screens don't flicker - or do they?”
AN1275,
“ISL45041EVAL1Z User’s Manual”
V
DD
5
A
VDD
2
SDA
SCL
6
7
I
2
C
INTERFACE
DAC
REGISTERS
ANALOG DCP
AND
CURRENT SINK
Q1
1
OUT
WP
3
7-BIT EEPROM
CURRENT SINK
ISL45041
4
GND
A1
8
SET
FIGURE 1. BLOCK DIAGRAM
April 22, 2016
FN6189.6
1
CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
1-888-INTERSIL or 1-888-468-3774 | Copyright Intersil Americas LLC. 2005- 2007, 2010, 2014, 2016. All Rights Reserved
Intersil (and design) is a trademark owned by Intersil Corporation or one of its subsidiaries.
All other trademarks mentioned are the property of their respective owners.
Has anyone written a program for DTH11 using the msp430f149 microcontroller?
I am using an msp430f149 microcontroller to measure the current temperature and humidity through a DTH11 temperature and humidity sensor. Can anyone share some existing code? Thank you very much!...
yejun5665 Microcontroller MCU
How to upgrade the bootloader?
The current development board has a bootloader. If I don't use jtag, can I use the current bootloader to download the new bootloader and then overwrite it? How should I do it specifically?...
Hellenlee Embedded System
【XMC4800 Relax EtherCAT Kit Review】+XMC4800+ unboxing and power on to start the journey of infineon
I have used MCU for many years, but this is the first time I have used Infineon. I got the opportunity to use it through the community. First of all, I would like to thank the EEWORLD community and in...
anger0925 Industrial Control Electronics
What is the load capacity of the I/O port of Motorola's MC9S08AC16?
As the title says. I just used this thing and I still don't know after reading the specification. How much current can the I/O of MC9S08AC16 drive? I hope you can give me an accurate data. Thank you....
lpredstar MCU
Please advise on the pulse program of STC
Control 1 motor, the highest frequency is 30KHZ, there are starting speed, maximum speed, and minimum speed, these 3 speeds can be selected arbitrarily between 300HZ~30KHZ, the number of 3 pulses can ...
sky999 MCU
Imported capacitors, does anyone know the specifications?
Does anyone know what size capacitor this is? There is no marking on the case....
zhuanangmos MCU

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2313  217  2095  887  2849  47  5  43  18  58 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号