EEWORLDEEWORLDEEWORLD

Part Number

Search

715P15296JA1

Description
Film Capacitor, Polypropylene, 600V, 10% +Tol, 10% -Tol, 0.0015uF, Through Hole Mount, RADIAL LEADED
CategoryPassive components    capacitor   
File Size554KB,14 Pages
ManufacturerCDE [ CORNELL DUBILIER ELECTRONICS ]
Environmental Compliance
Download Datasheet Parametric View All

715P15296JA1 Overview

Film Capacitor, Polypropylene, 600V, 10% +Tol, 10% -Tol, 0.0015uF, Through Hole Mount, RADIAL LEADED

715P15296JA1 Parametric

Parameter NameAttribute value
Is it Rohs certified?conform to
package instruction,
Reach Compliance Codeunknow
ECCN codeEAR99
Other featuresRATED AC VOLTAGE (V): 200
capacitance0.0015 µF
Capacitor typeFILM CAPACITOR
dielectric materialsPOLYPROPYLENE
JESD-609 codee3
Manufacturer's serial number715P
Installation featuresTHROUGH HOLE MOUNT
negative tolerance10%
Number of terminals2
Maximum operating temperature105 °C
Minimum operating temperature-55 °C
Package shapeRECTANGULAR PACKAGE
positive tolerance10%
Rated (DC) voltage (URdc)600 V
surface mountNO
Terminal surfaceTin (Sn)
Terminal shapeWIRE
Base Number Matches1
Type 715P, Orange Drop®, Polypropylene Film/Foil Capacitors
Features
• Long history of proven reliability
• Low dissipation factor.
• Tolerances as close as ±1%.
• Excellent stability, virtually linear
temperature coefficient.
• Various lead spacings, crimp styles
and lead lengths available.
Insulation Resistance:
400,000 M minimum at +25°C
20,000 M minimum at +85°C
2,000 M minimum at +105°C
Specifications
Capacitance Range:
Pulse Rise Time, dV/dt:
See tabulated data.
.001 µF to 0.47 µF
Corona Start Voltage (typical):
Capacitance Tolerance:
See tabulated data.
±1% to ±10%
Encapsulation:
Voltage Ratings:
100 to 2000 Volts D-C
70 to 500 Volts A-C
-55°C to +85°C
(+105°C with proper voltage derating)
Conformal coating of flame retardant orange
epoxy (meets UL94V-0 specifications)
Dielectric:
Operating Temperature Range:
Polypropylene film.
Non-inductively wound with extended
foil. Additional details on general
specifications page.
Switching and high voltage power
supplies, inverters, snubbers, resonant
converters and electronic lighting ballasts.
Construction:
Lead Wire:
Tinned copper-clad steel,
.032 (0.8) diameter, #20 AWG
Applications:
Dissipation Factor:
See tabulated data.
Dimensions in inches, metric (mm) in parenthesis.
CDE Cornell Dubilier • 1605 E. Rodney French Blvd. • New Bedford, MA 02744 • Phone: (508)996-8561 • Fax: (508)996-3830
Test CY8CKIT-042-BLE development board routine 1 on mobile version Win8
[i=s]This post was last edited by dcexpert on 2015-2-9 00:52[/i] After two days of hard work, I finally installed the mobile version of Win8.1 on the mobile hard disk and PSoc creator 3.1. I can try t...
dcexpert MCU
Discussion on the development confusion and practical operation problems of small engineering companies (V)
5. Site management 1. From the structure, it can be seen that the HR plays the role of a foreman, managing the company's construction personnel and temporary construction personnel, ensuring the quali...
john_wang Industrial Control Electronics
[Video Sharing] Riding the Small Cell Wave - New TCI6636 SoC and KeyStone II Multi-core Architecture
Introduction: Ruwanga Dassanayake of Texas Instruments introduces how TI uses the latest system-on-chip TCI6636 to further innovate the base station market. The challenges faced by operators today are...
德州仪器_视频 DSP and ARM Processors
Calculation of timer interrupt and baud rate in single chip microcomputer
There is a question, when the baud rate is 1200, a frame of data is sent, the length is 10 (1 start, 8 data, 1 stop). The crystal oscillator is 11.0592MHZ, and the duration of sending and receiving is...
20041143kk Embedded System
Classification and characteristics of PIC 8-bit microcontrollers
The PIC microcontroller series products launched by Microchip of the United States first adopted the embedded microcontroller with RISC structure. Its high speed, low voltage, low power consumption, h...
护花使者 Microchip MCU
Why is the external interrupt flag P2IFG always set?
I wrote the code to set P2IFG=0x00; but when debugging, I connected a 60HZ square wave to P2.0, and the corresponding bit of P2IFG was always set. Even if I only connected a Dupont line (without decod...
cdy200824 Microcontroller MCU

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2786  1314  634  418  1802  57  27  13  9  37 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号