The semi-regulated, wide input Quarter-Brick Intermediate Bus
Converter (IBC) model is a new high efficiency, open-frame,
isolated, 28A converter in an industry standard quarter-brick
footprint. This IBC provides designers with an extremely energy-
efficient, cost effective solution for main on-board power source in
12VDC distributed power systems. In these systems, the IBC is
intended primarily for powering multiple downstream non-
isolated point-of-load (POL) converters. Operating from a 36 to
75VDC supply, this converter will also optimize the performance of
its downstream POL converters by maintaining a constant output
voltage independent of line fluctuations that are common in
telecom applications.
Additionally, a patent pending, full wavecoupled inductor
topology yields some of the highest full load efficiencies in the
industry. All Quarter-Brick converters have, as standard features,
remote ON/OFF capability, overcurrent, overvoltage and
undervoltage protection and full international safety approval
including EN60950-1 VDE and UL/cUL60950-1.
Technical Reference Note -
QUARTER-BRICK SERIES
Semi-regulated 12 Volt Output
Rev.12.12.07
quarter-brick series
2 of 12
Stresses in excess of the maximum ratings can cause permanent damage to the device. Operation of the device is not implied at these or any other conditions
in excess of those given in the specification. Exposure to absolute maximum ratings can adversely affect device reliability.
Absolute Maximum Ratings
Characteristic
Input voltage - continuous
Input voltage -peak/surge
Input voltage - remote pin
Operating temperature
Storage temperature
Output power
Symbol
Vin (cont)
Vin (peak)
Vrem (peak)
Top
Tstorage
Pout (max)
Min
-0.3
-0.3
Typ
Max
75
100
Units
V DC
V DC
Notes and Conditions
Vin(+) - Vin(-)
Transients of 100 msec or less,
in duration
Peaks of any duration
Measured at hotspot
-0.3
-40
-55
20
120
125
336
V DC
°C
°C
W
All specifications are typical at nominal input Vin =
48V,
and with full rated resistive load at 25˚C ambient unless otherwise specified.
Input Characteristics
Characteristic
Input voltage - operating
Input current - no load
Input current - quiescent
Inrush current (I
2
t)
Inrush current ratio
Input ripple rejection
Input fuse
Symbol
Vin (oper)
lin
lin (off)
Iinrush
It/Im
Min
36
Typ
48
120
5.5
0.14
22
50
20
dB
A
Frequency <1kHz
Slow Blow/Antisurge HRC
recommended 250V Rating.
See Application Note 190
Max
75
140
8
Units
V DC
mA DC
mA DC
A
2
S
Vin (min) to Vin (max), enabled
Converter disabled
Notes and Conditions
Turn On/Off
Characteristic
Input voltage - turn on
Input voltage - turn off
Turn on delay - enabled,
then power applied
Symbol
Vin (on)
Vin (off)
Tdelay (power)
32
Min
Typ
34.5
33
15
25
Max
36
Units
V DC
V DC
msec
With Remote ON/OFF signal
asserted, time from when Vin >
Vin (oper) until Vout is within
total regulation band
With Vin = Vin (nom), then
remote ON/OFF asserted, time
until Vo is within total error band
Rise time
Trise
3
6
msec
From 10% to 90%, full resistive
load, no external capacitance
Notes and Conditions
Turn on delay - power
applied, then enabled
Tdelay
5
8
msec
Technical Reference Note -
QUARTER-BRICK SERIES
Semi-regulated 12 Volt Output
Rev.12.12.07
quarter-brick series
3 of 12
Signal Electrical Interface
Characteristic
At remote ON/OFF (control) pin
Open collector or equivalent
compatible
Control pin open circuit voltage
High level input voltage
Vih
Vih
2.4
4.6
5.0
20
V
V
Vih (min)
High level input current
Iih
10
μA
Current flowing into control pin
when pin is pulled high
(max. at Vih = 75V)
Acceptable leakage current from
signal pin into the open collector
driver (neg = from converter)
Converter guaranteed OFF
when control pin is less than
Vil (max)
ViI = 0.0V, maximum source
current from converter with short
circuit
Iih = 0μA; open circuit voltage
Converter guaranteed ON when
when control pin is greater than
Symbol
Min
Typ
Max
Units
Notes and Conditions
See Notes 1 and 2
Acceptable high level
leakage current
Iih (leakage)
-10
μA
Low level input voltage
ViI
-0.3
0.4
V
Low level input current
Iil (max)
-0.6
-0.75
mA
Common Protection/Control
Characteristic
Overtemperature shutdown
threshold
Symbol
Tots
Min
120
Typ
125
Max
130
Units
°C
Notes and Conditions
Hotspot temperature, non-
latching shutdown protection.
See Application Note 190
Reliability and Service Life
Characteristic
Mean time between failure
Symbol
MTBF
Min
Typ
5,467,917
Max
Units
Hours
Notes and Conditions
Telcordia Tech. SR-332
Tamb = 25°C, Tcase = 20°C rise
airflow = 400LFM,
Vin = Vin (nom),
Iout = 50% Iout (max)
Isolation
88Characteristic
Input to output test voltage
Input to output capacitance
Input to output resistance
Input to output insulation system
10
Basic
1200
Symbol
Min
Typ
Max
2,250
Units
V DC
pF
MΩ
Measured with 500VDC
Notes and Conditions
Test duration 1s
Technical Reference Note -
QUARTER-BRICK SERIES
Semi-regulated 12 Volt Output
Rev.12.12.07
quarter-brick series
4 of 12
Other Specifications
Characteristic
Switching frequency
Symbol
fsw
Min
Typ
400
Max
Units
kHz
Notes and Conditions
Fixed frequency (all models)
Environmental Specifications
Characteristic
Thermal performance
Altitude
Symbol
Min
-40
Typ
Max
120
3,000
9843
10,000
32,808
Parameter
Reference
IEC 60068-2-1 Ab/Ad:
Cold
IEC680068-2-2 Bb/Bd:
Dry heat
IEC 68-2-14 Nb: Rate of
change
Relative humidity
IEC 60068-2-56 Cb: damp
heat, steady state
Vibration
IEC60068-2-6 Fc:
sinusoidal
Test Level
-40°C, 16h
+70°C, 16h
-5°C/+45°C, 0.5°C/min 2 cycles, 3h ea
Units
°C
m
ft
m
ft
Notes and Conditions
Hotspot temperature
derate total max. output current
by 20%
derate total max. output current
by 50%
Type
Air temperature
+35°C, 93% RH, 4 days 50% of samples powered at
10% load and 50% unpowered
3 axes, 5 sweeps per axis unpowered on test card
Freq. range and displacement 5-9Hz, 1.2mm
Freq. Range and acceleration 9-200Hz, 10m/s
2
100 bumps each of 6 directions, mounted on powered on
[i=s]This post was last edited by liutogo on 2015-6-1 00:15[/i] I applied successfully again, but Ti adjusted the number of samples I applied for. But I am still very grateful to Ti....
In Keil, what is the difference between const char code tab1[]; const char far tab2[]; and these two arrays? When should I add code and when should I add far?...
[i=s] This post was last edited by Yitanqingshui on 2014-8-14 21:43 [/i] 1. First select the company in the FPGA power supply in FPGA/uP, and then select the corresponding chip2. The power supply poin...
Shenzhen Jiachuangda Technology Co., Ltd. Changsha Branch is the "computer room maintenance master" in the domestic industry. Jiachuangda's main business includes computer room power environment centr...
I feel that the functions of some embedded development boards are almost the same as those of computer motherboards. They have all kinds of interfaces and are full of functions. I suddenly realized th...
1. Introduction
Since the 1980s, with the continuous development of automotive electronic technology, there are more and more electronic control units in automobiles, such as electronic fuel i...[Details]
In recent years, the market for mobile/portable devices such as smartphones and laptops has continued to grow rapidly. While these products continue to integrate more new features to enhance the ...[Details]
1. Introduction
Light control circuit plays a vital role in urban street lamps or corridor lighting. With light control circuit, the lights can be automatically turned on and off according to ...[Details]
General LED lighting has a current limiting resistor in the driving circuit, and the power consumed by the resistor has nothing to do with the LED light emission. In order to improve efficiency, a...[Details]
Among the many members of the single-chip microcomputer family, the MCS-51 series of single-chip microcomputers has occupied the main market of industrial measurement and control and automation eng...[Details]
From the previous section, we have learned that the timer/counter in the microcontroller can have multiple uses, so how can I make them work for the purpose I need? This requires setting the timer/...[Details]
Investment in
the
medical device
industry has been on the rise in recent years. In the past two years, venture capital for medical devices has almost doubled, reaching $4 billion in 2007. Fr...[Details]
Recently, news came from the certification department that the photovoltaic grid-connected inverter of Samil New Energy Co., Ltd. (hereinafter referred to as "Samil New Energy") has once again obta...[Details]
Introduction
As the country increases its efforts to control the atmospheric environment, motorcycle emission regulations will become stricter year by year, and motorcycles that do not meet the...[Details]
1. Proposal of
reconfigurable
measurement and control system
The measurement and control system generally refers to a system based on
computers
to realize data acquisition a...[Details]
A stepper motor is an electromagnetic mechanical device that converts an electrical pulse signal into an angular displacement or a linear displacement. The stability and reliability of a stepper mo...[Details]
0 Introduction
There are many types of sensors, and the working principles, measurement targets and measurement environments of different types of sensors vary greatly. The corresponding detection s...[Details]
Introduction
Today, as IC (integrated circuit) has developed to a super-large scale, IC design based on IP (Intellectual Property) cores and their reuse are important means to ensure the ef...[Details]
Zarlink Semiconductor has developed an ultra-low-power RF transceiver chip for pacemakers, neurostimulators, drug pumps, and other such implantable medical devices. It has high data rates, low power c...[Details]
The demand for improved healthcare environments is endless, so medical imaging equipment with higher resolution is needed to better observe the human body. High resolution brings problems with sign...[Details]
TI Technology Forum
京公网安备 11010802033920号
EEWORLD
