HIGH-SPEED
8K x 16 DUAL-PORT
STATIC RAM
Features
x
x
x
IDT7025S/L
x
x
True Dual-Ported memory cells which allow simultaneous
reads of the same memory location
High-speed access
– Military: 20/25/35/55/70ns (max.)
– Industrial: 55ns (max.)
– Commercial: 15/17/20/25/35/55ns (max.)
Low-power operation
– IDT7025S
Active: 750mW (typ.)
Standby: 5mW (typ.)
– IDT7025L
Active: 750mW (typ.)
Standby: 1mW (typ.)
Separate upper-byte and lower-byte control for multiplexed
bus compatibility
x
x
x
x
x
x
x
x
x
IDT7025 easily expands data bus width to 32 bits or more
using the Master/Slave select when cascading more than
one device
M/S = H for
BUSY
output flag on Master
M/S = L for
BUSY
input on Slave
Interrupt Flag
On-chip port arbitration logic
Full on-chip hardware support of semaphore signaling
between ports
Fully asynchronous operation from either port
Battery backup operation—2V data retention
TTL-compatible, single 5V (±10%) power supply
Available in 84-pin PGA, Flatpack, PLCC, and 100-pin Thin
Quad Flatpack
Industrial temperature range (–40°C to +85°C) is available
for selected speeds
Functional Block Diagram
R/W
L
UB
L
R/W
R
UB
R
LB
L
CE
L
OE
L
LB
R
CE
R
OE
R
I/O
8L
-I/O
15L
I/O
0L
-I/O
7L
BUSY
L
A
12L
A
0L
(1,2)
I/O
8R
-I/O
15R
I/O
Control
I/O
Control
I/O
0R
-I/O
7R
BUSY
R
Address
Decoder
13
(1,2)
MEMORY
ARRAY
13
Address
Decoder
A
12R
A
0R
CE
L
OE
L
R/W
L
SEM
L
(2)
INT
L
NOTES:
1. (MASTER):
BUSY
is output; (SLAVE):
BUSY
is input.
2.
BUSY
outputs and
INT
outputs are non-tri-stated push-pull.
ARBITRATION
INTERRUPT
SEMAPHORE
LOGIC
CE
R
OE
R
R/W
R
SEM
R
INT
R
(2)
2683 drw 01
M/S
APRIL 2000
1
©2000 Integrated Device Technology, Inc.
DSC 2683/8
IDT7025S/L
High-Speed 8K x 16 Dual-Port Static RAM
Military, Industrial and Commercial Temperature Ranges
Description
The IDT7025 is a high-speed 8K x 16 Dual-Port Static RAM. The
IDT7025 is designed to be used as a stand-alone 128K-bit Dual-Port RAM
or as a combination MASTER/SLAVE Dual-Port RAM for 32-bit or more
word systems. Using the IDT MASTER/SLAVE Dual-Port RAM approach
in 32-bit or wider memory system applications results in full-speed, error-
free operation without the need for additional discrete logic.
This device provides two independent ports with separate control,
address, and I/O pins that permit independent, asynchronous access for
reads or writes to any location in memory. An automatic power down
feature controlled by Chip Enable (CE) permits the on-chip circuitry of each
port to enter a very low standby power mode.
Fabricated using IDT’s CMOS high-performance technology, these
devices typically operate on only 750mW of power. Low-power (L)
versions offer battery backup data retention capability with typical power
consumption of 500µW from a 2V battery.
The IDT7025 is packaged in a ceramic 84-pin PGA, an 84-pin
Flatpack, PLCC, and a 100-pin TQFP. Military grade product is manu-
factured in compliance with the latest revision of MIL-PRF-38535 QML,
making it ideally suited to military temperature applications demanding the
highest level of performance and reliability.
I/O
3L
I/O
2L
I/O
1L
I/O
0L
GND
R/W
L
I/O
5L
I/O
4L
I/O
7L
I/O
6L
SEM
L
Pin Configurations
(1,2,3)
A
11L
CE
L
UB
L
LB
L
A
12L
OE
L
V
CC
A
10L
A
9L
INDEX
11 10 9 8 7 6 5 4 3 2 1 84 83 82 81 80 79 78 77 76 75
74
73
72
71
70
69
68
IDT7025J or F
J84-1
(4)
F84-2
(4)
84-Pin PLCC/Flatpack
Top View
(5)
67
66
65
64
63
62
61
60
59
58
57
56
55
A
8L
A
7L
A
6L
A
5L
A
4L
A
3L
A
2L
A
1L
A
0L
INT
L
BUSY
L
GND
M/S
BUSY
R
INT
R
A
0R
A
1R
A
2R
A
3R
A
4R
A
5R
A
6R
2683 drw 02
I/O
8L
I/O
9L
I/O
10L
I/O
11L
I/O
12L
I/O
13L
GND
I/O
14L
I/O
15L
V
CC
GND
I/O
0R
I/O
1R
I/O
2R
V
CC
I/O
3R
I/O
4R
I/O
5R
I/O
6R
I/O
7R
I/O
8R
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
54
32
33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53
GND
GND
I/O
15R
OE
R
R/W
R
SEM
R
A
11R
UB
R
A
10R
A
9R
I/O
9R
A
12R
A
8R
I/O
12R
CE
R
I/O
10R
I/O
11R
I/O
13R
I/O
14R
LB
R
A
7R
NOTES:
1. All V
CC
pins must be connected to power supply.
2. All GND pins must be connected to ground supply.
3. J84-1 package body is approximately 1.15 in x 1.15 in x .17 in.
F84-2 package body is approximately 1.17 in x 1.17 in x .11 in.
PN100-1 package body is approximately 14mm x 14mm x 1.4mm.
4. This package code is used to reference the package diagram.
5. This text does not indicate orientation of the actual part-marking.
N/C
N/C
N/C
N/C
I/O
10L
I/O
11L
I/O
12L
I/O
13L
GND
I/O
14L
I/O
15L
V
CC
GND
I/O
0R
I/O
1R
I/O
2R
V
CC
I/O
3R
I/O
4R
I/O
5R
I/O
6R
N/C
N/C
N/C
N/C
1
2
3
4
5
6
7
8
9
100 99 98 97 96 95 94 93 92 91 90 89 88 87 86 85 84 83 82 81 80 79 78 77 76
75
74
73
72
71
70
69
68
I/O
9L
I/O
8L
I/O
7L
I/O
6L
I/O
5L
I/O
4L
I/O
3L
I/O
2L
GND
I/O
1L
I/O
0L
OE
L
V
CC
R/W
L
SEM
L
CE
L
UB
L
LB
L
A
12L
A
11L
A
10L
A
9L
A
8L
A
7L
A
6L
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
Index
IDT7025PF
PN100-1
(4)
100-Pin TQFP
Top View
(5)
67
66
65
64
63
62
61
60
59
58
57
56
55
54
53
52
51
25
26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50
N/C
N/C
N/C
N/C
A
5L
A
4L
A
3L
A
2L
A
1L
A
0L
INT
L
BUSY
L
GND
M/S
BUSY
R
INT
R
A
0R
A
1R
A
2R
A
3R
A
4R
N/C
N/C
N/C
N/C
.
I/O
7R
I/O
8R
I/O
9R
I/O
10R
I/O
11R
I/O
12R
I/O
13R
I/O
14R
GND
I/O
15R
OE
R
R/W
R
GND
SEM
R
CE
R
UB
R
LB
R
A
12R
A
11R
A
10R
A
9R
A
8R
A
7R
A
6R
A
5R
2683 drw 03
6.42
2
IDT7025S/L
High-Speed 8K x 16 Dual-Port Static RAM
Military, Industrial and Commercial Temperature Ranges
Pin Configurations
(1,2,3)
(con't.)
63
61
60
58
55
54
51
48
46
45
42
11
I/O
7L
66
I/O
5L
64
I/O
4L
62
I/O
2L
59
I/O
0L
56
OE
L
49
SEM
L
50
LB
L
47
A
11L
44
A
10L
43
A
7L
40
10
I/O
10L
67
I/O
8L
65
I/O
6L
I/O
3L
I/O
1L
57
UB
L
53
CE
L
52
A
12L
A
9L
A
8L
41
A
5L
39
09
I/O
11L
69
I/O
9L
68
GND
V
CC
R/
W
L
A
6L
38
A
4L
37
08
I/O
13L
72
I/O
12L
71
73
33
A
3L
35
A
2L
34
07
I/O
15L
75
I/O
14L
70
V
CC
74
BUSY
L
IDT7025G
G84-3
(4)
84-Pin PGA
Top View
(5)
32
A
0L
31
INT
L
36
06
I/O
0R
76
GND
77
GND
78
GND
28
M/
S
29
A
1L
30
05
I/O
1R
79
I/O
2R
80
V
CC
A
0R
INT
R
26
BUSY
R
27
04
I/O
3R
81
I/O
4R
83
7
11
12
A
2R
23
A
1R
25
03
I/O
5R
82
1
I/O
7R
2
5
GND
8
GND
10
SEM
R
14
17
20
A
5R
22
A
3R
24
02
I/O
6R
84
3
I/O
9R
I/O
10R
4
I/O
13R
6
I/O
15R
9
R/
W
R
15
UB
R
13
A
11R
16
A
8R
18
A
6R
19
A
4R
21
01
I/O
8R
A
I/O
11R
B
I/O
12R
C
I/O
14R
D
OE
R
E
LB
R
F
CE
R
G
A
12R
H
A
10R
J
A
9R
K
A
7R
L
2683 drw 04
Index
NOTES:
1. All V
CC
pins must be connected to power supply.
2. All GND pins must be connected to ground supply.
3. Package body is approximately 1.12 in x 1.12 in x .16 in.
4. This package code is used to reference the package diagram.
5. This text does not indicate orientation of the actual part-marking.
Pin Names
Left Port
Right Port
Names
Chip Enable
Read/Write Enable
Output Enable
Address
Data Input/Output
Semaphore Enable
Upper Byte Select
Lower Byte Select
Interrupt Flag
Busy Flag
Master or Slave Select
Power
Ground
2683 tbl 01
CE
L
R/
W
L
CE
R
R/
W
R
OE
L
A
0L
- A
12L
I/O
0L
- I/O
15L
OE
R
A
0R
- A
12R
I/O
0R
- I/O
15R
SEM
L
UB
L
LB
L
INT
L
BUSY
L
SEM
R
UB
R
LB
R
INT
R
BUSY
R
M/
S
V
CC
GND
6.42
3
IDT7025S/L
High-Speed 8K x 16 Dual-Port Static RAM
Military, Industrial and Commercial Temperature Ranges
Truth Table I: Non-Contention Read/Write Control
Inputs
(1)
Outputs
CE
H
X
L
L
L
L
L
L
X
NOTE:
R/
W
X
X
L
L
L
H
H
H
X
OE
X
X
X
X
X
L
L
L
H
UB
X
H
L
H
L
L
H
L
X
LB
X
H
H
L
L
H
L
L
X
SEM
H
H
H
H
H
H
H
H
X
I/O
8-15
High-Z
High-Z
DATA
IN
High-Z
DATA
IN
DATA
OUT
High-Z
DATA
OUT
High-Z
I/O
0-7
High-Z
High-Z
High-Z
DATA
IN
DATA
IN
High-Z
DATA
OUT
DATA
OUT
High-Z
Deselected
Mode
Both Bytes Deselected
Write to Upper Byte Only
Write to Lower Byte Only
Write to Both Bytes
Read Upper Byte Only
Read Lower Byte Only
Read Both Bytes
Outputs Disabled
2683 tbl 02
1. A
0L
— A
12L
≠
A
0R
— A
12R.
Truth Table II: Semaphore Read/Write Control
(1)
Inputs
Outputs
CE
H
X
H
X
L
L
R/
W
H
H
↑
↑
X
X
OE
L
L
X
X
X
X
UB
X
H
X
H
L
X
LB
X
H
X
H
X
L
SEM
L
L
L
L
L
L
I/O
8-15
DATA
OUT
DATA
OUT
DATA
IN
DATA
IN
____
I/O
0-7
DATA
OUT
DATA
OUT
DATA
IN
DATA
IN
____
Mode
Read Semaphore Flag Data Out
Read Semaphore Flag Data Out
Write I/O
0
into Semaphore Flag
Write I/O
0
into Semaphore Flag
Not Allowed
Not Allowed
2683 tbl 03
____
____
NOTES:
1. There are eight semaphore flags written to via I/O
0
and read from I/O
0
- I/O
15.
These eight semaphores are addressed by A
0
- A
2
.
6.42
4
IDT7025S/L
High-Speed 8K x 16 Dual-Port Static RAM
Military, Industrial and Commercial Temperature Ranges
Absolute Maximum Ratings
(1)
Symbol
V
TERM
(2)
Rating
Terminal Voltage
with Respect
to GND
Temperature
Under Bias
Storage
Temperature
DC Output
Current
Commercial
& Industrial
-0.5 to +7.0
Military
-0.5 to +7.0
Unit
V
Maximum Operating Temperature
and Supply Voltage
(1,2)
Grade
Ambient Temperature
Military
-55
O
C to +125
O
C
0
O
C to +70
O
C
-40
O
C to +85
O
C
0V
0V
0V
5.0V
+
10%
5.0V
+
10%
5.0V
+
10%
2683 tbl 05
GND
Vcc
T
BIAS
T
STG
I
OUT
-55 to +125
-55 to +125
50
-65 to +135
-65 to +150
50
o
C
C
Commercial
Industrial
o
mA
2683 tbl 04
NOTES:
1. This is parameter T
A
.
2. Industrial temperature: for other speeds, packages and powers contact your
sales office.
NOTES:
1. Stresses greater than those listed under ABSOLUTE MAXIMUM RATINGS may
cause permanent damage to the device. This is a stress rating only and
functional operation of the device at these or any other conditions above those
indicated in the operational sections of this specification is not implied. Exposure
to absolute maximum rating conditions for extended periods may affect
reliability.
2. V
TERM
must not exceed Vcc + 10% for more than 25% of the cycle time or 10ns
maximum, and is limited to < 20 mA for the period over V
TERM
> Vcc + 10%.
Recommended DC Operating
Conditions
Symbol
V
CC
GND
Parameter
Supply Voltage
Ground
Input High Voltage
Input Low Voltage
Min.
4.5
0
2.2
-0.5
(1)
Typ.
5.0
0
____
Max.
5.5
0
6.0
(2)
0.8
Unit
V
V
V
V
2683 tbl 06
Capacitance
(1)
(T
A
= +25°C, f = 1.0mhz)
Symbol
C
IN
C
OUT
Parameter
Input Capacitance
Output Capacitance
Conditions
(2)
V
IH
V
IL
____
Max.
9
10
Unit
pF
pF
2683 tbl 07
V
IN
= 3dV
V
OUT
= 3dV
NOTES:
1. V
I
L
> -1.5V for pulse width less than 10ns.
2. V
TERM
must not exceed Vcc + 10%.
NOTES:
1. This parameter is determined by device characterization but is not production
tested. For TQFP package only.
2. 3dV references the interpolated capacitance when the input and output signals
switch from 0V to 3V or from 3V to 0V.
DC Electrical Characteristics Over the Operating
Temperature and Supply Voltage Range
(V
CC
= 5.0V ± 10%)
7025S
Symbol
|I
LI
|
|I
LO
|
V
OL
V
OH
Parameter
Input Leakage Current
(1)
Output Leakage Current
Output Low Voltage
Output High Voltage
Test Conditions
V
CC
= 5.5V, V
IN
= 0V to V
CC
V
OUT
= 0V to V
CC
I
OL
= +4mA
I
OH
= -4mA
Min.
___
___
___
7025L
Max.
10
10
0.4
___
Min.
___
___
___
Max.
5
5
0.4
___
Unit
µA
µA
V
V
2683 tbl 08
2.4
2.4
NOTE:
1. At Vcc < 2.0V input leakages are undefined.
6.42
5
京公网安备 11010802033920号
EEWORLD
