IS62LV2568ALL
256K x 8 LOW POWER and LOW Vcc
CMOS STATIC RAM
FEATURES
• Access times of 70 and 85 ns
•
CMOS low power operation:
— 120 mW (typical) operating
— 6 µW (typical) standby
• Low data retention voltage: 2V (min.)
• Output Enable (OE) and two Chip Enable
(CE1 and CE2) inputs for ease in applications
• TTL compatible inputs and outputs
• Fully static operation:
— No clock or refresh required
• Single 2.5V (min.) to 3.3V (max.) power supply
• Available in 32-pin TSOP (Type I), STSOP (Type I),
and 36-pin mini BGA
ISSI
DESCRIPTION
®
AUGUST 2001
The
ISSI
IS62LV2568ALL is a low voltage, 262,144 words
by 8 bits, CMOS SRAM. It is fabricated using
ISS
I'’
s low
voltage, six transistor (6T), CMOS technology. The device is
targeted to satisfy the demands of the state-of-the-art
technologies such as cell phones and pagers.
When
CE
is HIGH (deselected), the device assumes a
standby mode at which the power dissipation can be reduced
down with CMOS input levels. Additionally, easy memory
expansion is provided by using Chip Enable and Output
Enable inputs,
CE
and
OE.
The active LOW Write Enable (WE)
controls both writing and reading of the memory.
The IS62LV2568ALL is available in 32-pin TSOP (Type I),
STSOP (Type I), and 36-pin mini BGA.
FUNCTIONAL BLOCK DIAGRAM
A0-A17
DECODER
256K x 8
MEMORY ARRAY
VCC
GND
I/O
DATA
CIRCUIT
I/O0-I/O7
COLUMN I/O
CE1
CE2
OE
WE
CONTROL
CIRCUIT
ISSI reserves the right to make changes to its products at any time without notice in order to improve design and supply the best possible product. We assume no responsibility for any
errors which may appear in this publication. © Copyright 2001, Integrated Silicon Solution, Inc.
Integrated Silicon Solution, Inc. — 1-800-379-4774
Rev. B
08/01/01
1
IS62LV2568ALL
ISSI
CE1
H
X
L
L
L
CE2
X
L
H
H
H
OE
X
X
H
L
X
I/O Operation
High-Z
High-Z
High-Z
D
OUT
D
IN
Vcc Current
I
SB
1
, I
SB
2
I
SB
1
, I
SB
2
I
CC
I
CC
I
CC
®
TRUTH TABLE
Mode
Not Selected
(Power-down)
Output Disabled
Read
Write
WE
X
X
H
H
L
OPERATING RANGE
Range
Commercial
Industrial
Ambient Temperature
0°C to +70°C
–40°C to +85°C
V
CC
M
IN
.
2.5V
2.5V
V
CC
M
AX
.
3.3V
3.3V
ABSOLUTE MAXIMUM RATINGS
(1)
Symbol
V
TERM
V
CC
T
BIAS
T
STG
P
T
Parameter
Terminal Voltage with Respect to GND
Vcc related to GND
Temperature Under Bias
Storage Temperature
Power Dissipation
Value
–0.5 to Vcc + 0.5
–0.3 to +3.6
–40 to +85
–65 to +150
0.7
Unit
V
V
°C
°C
W
Note:
1. Stress greater than those listed under ABSOLUTE MAXIMUM RATINGS may cause
permanent damage to the device. This is a stress rating only and functional operation of the
device at these or any other conditions above those indicated in the operational sections of
this specification is not implied. Exposure to absolute maximum rating conditions for
extended periods may affect reliability.
CAPACITANCE
(1,2)
Symbol
C
IN
C
OUT
Parameter
Input Capacitance
Output Capacitance
Conditions
V
IN
= 0V
V
OUT
= 0V
Max.
6
8
Unit
pF
pF
Notes:
1. Tested initially and after any design or process changes that may affect these parameters.
2. Test conditions: T
A
= 25°C, f = 1 MHz, Vcc = 3.0V.
Integrated Silicon Solution, Inc. — 1-800-379-4774
Rev. B
08/01/01
3
IS62LV2568ALL
DC ELECTRICAL CHARACTERISTICS
(Over Operating Range)
Symbol Parameter
V
OH
V
OL
V
IH
V
IL
I
LI
I
LO
Output HIGH Voltage
Output LOW Voltage
Input HIGH Voltage
Input LOW Voltage
(1)
Input Leakage
Output Leakage
Test Conditions
V
CC
= Min., I
OH
= –1.0 mA
V
CC
= Min., I
OL
= 2.1 mA
Min.
2.0
—
2.2
–0.3
–1
–1
ISSI
Max.
—
0.4
V
CC
+ 0.3
0.4
1
1
V
V
V
V
µA
µA
®
Unit
GND
≤
V
IN
≤
V
CC
GND
≤
V
OUT
≤
V
CC
Note:
1. V
IL
= –3.0V for pulse width less than 10 ns.
POWER SUPPLY CHARACTERISTICS
(1)
(Over Operating Range)
Symbol Parameter
I
CC
Vcc Dynamic
Operating
Supply Current
TTL Standby
Current
(TTL Inputs)
CMOS Standby
Current
(CMOS Inputs)
Test Conditions
V
CC
= Max., CE = V
IL
I
OUT
= 0 mA, f = f
MAX
Com.
Ind.
-70
Min.
Max.
—
—
—
—
—
—
30
35
0.4
1.0
5
5
-85
Min.
Max.
—
—
—
—
—
—
25
30
0.4
1.0
5
5
Unit
mA
I
SB
1
V
CC
= Max.,
Com.
V
IN
= V
IH
or V
IL
,
Ind.
CE1
≥
V
IH
or CE2
≤
V
IL
, f = 0
V
CC
= Max., f = 0
Com.
CE1
≥
V
CC
– 0.2V,
Ind.
CE2
≤
0.2V,
or V
IN
≥
V
CC
– 0.2V, V
IN
≤
0.2V
mA
I
SB
2
µA
Note:
1. At f = f
MAX
, address and data inputs are cycling at the maximum frequency, f = 0 means no input lines change.
4
Integrated Silicon Solution, Inc. — 1-800-379-4774
Rev. B
08/01/01
IS62LV2568ALL
READ CYCLE SWITCHING CHARACTERISTICS
(1)
(Over Operating Range)
-70
Symbol
Parameter
Read Cycle Time
Address Access Time
Output Hold Time
CE1
Access Time
CE2 Access Time
OE
Access Time
OE
to High-Z Output
OE
to Low-Z Output
CE1
to Low-Z Output
CE2 to Low-Z Output
CE1
or CE2 to High-Z Output
Min.
70
—
10
—
—
—
—
5
10
10
0
Max.
—
70
—
70
70
35
25
—
—
—
25
Min.
85
—
15
—
—
—
—
5
10
10
0
-85
Max.
—
85
—
85
85
45
25
—
—
—
25
ISSI
Unit
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
®
t
RC
t
AA
t
OHA
t
ACE
1
t
ACE
2
t
DOE
t
HZOE
(2)
t
LZOE
(2)
t
LZCE
1
(2)
t
LZCE
2
(2)
t
HZCE
(2)
Notes:
1. Test conditions assume signal transition times of 5 ns or less, timing reference levels of 1.3V, input pulse levels of 0.4V to 2.2V and
output loading specified in Figure 1.
2. Tested with the load in Figure 2. Transition is measured ±500 mV from steady-state voltage. Not 100% tested.
AC TEST CONDITIONS
Parameter
Input Pulse Level
Input Rise and Fall Times
Input and Output Timing
and Reference Level
Output Load
Unit
0.4V to 2.2V
5 ns
1.3V
See Figures 1 and 2
AC TEST LOADS
3070
Ω
2.8V
2.8V
3070
Ω
OUTPUT
30 pF
Including
jig and
scope
3150
Ω
OUTPUT
5 pF
Including
jig and
scope
3150
Ω
Figure 1
Figure 2
Integrated Silicon Solution, Inc. — 1-800-379-4774
Rev. B
08/01/01
5
RF/Wirelessly
京公网安备 11010802033920号
EEWORLD
