EEWORLDEEWORLDEEWORLD

Part Number

Search

PH1-FLALC3242

Description
Transponder, 10660Mbps(Tx), 10660Mbps(Rx), LC/SPC Connector,
CategoryWireless rf/communication    Optical fiber   
File Size240KB,6 Pages
ManufacturerJDS Uniphase Corporation ( VIAVI )
Websitehttp://www.jdsu.com/index.html
Download Datasheet Parametric View All

PH1-FLALC3242 Overview

Transponder, 10660Mbps(Tx), 10660Mbps(Rx), LC/SPC Connector,

PH1-FLALC3242 Parametric

Parameter NameAttribute value
MakerJDS Uniphase Corporation ( VIAVI )
Reach Compliance Codeunknown
Other featuresIT ALSO OPERATE FROM 1280NM TO 1600NM
body height13.2 mm
Body length or diameter84.1 mm
Connection TypeLC/SPC CONNECTOR
Data rate (receive)10660 Mbps
Data rate (send)10660 Mbps
Emitter/Detector TypeAVALANCHE PHOTODIODE
Fiber optic equipment typesTRANSCEIVER, TRANSPONDER
Nominal operating wavelength1541 nm
Nominal optical power output1.584 mW
minimum return loss-27 dB
Sensitivity-24 dBm
COMMUNICATIONS MODULES & SUBSYSTEMS
10 Gb/s TDM/DWDM 300 Pin SFF MSA SR2/IR2/LR2 Transponder
PH1 Series
Key Features
• Three configurations supporting SR2/IR2/LR2 applications
• Supports dense wavelength division multiplexing
(DWDM) applications (without wavelocker)
• Microprocessor controls to support I2C
• Integrated 16:1/1:16 mux/demux
• Small form factor package (2.2" x 3.0" x 0.53") for high
density applications
• Low power consumption: 4.8 W typical, 6.8 W maximum
for TDM applications
• 70 °C maximum operating temperature
• High sensitivity PIN or APD receivers
• SONET, FEC, Ethernet and Multirate Capable Versions
• Forward, counter and line timing clocking modes
Applications
Telecommunications
Metropolitan Area Networks
Subscriber loop
Intra-office SONET/SDH
High bit-rate data communications
JDSU 10 Gb/s PH1 Series transponders are intended for 1550 nm system
applications with reaches of up to 80 km. The series includes three different
transponders for SR2 (25 km), IR2 (40 km), and LR2 (80 km) TDM or DWDM
applications. Each transponder accepts 16 bits of parallel digital data and converts
it to a 10 Gb/s NRZ modulated optical signal. It also accepts a 10 Gb/s NRZ
modulated optical signal and converts it into 16 bit wide parallel digital data.
The PH1 series offers low DC power dissipation and is available in either a small
form factor package (2.2 x 3 x 0.53 inches) or in a larger footprint (3.5 x 4.5 x 0.53
inches) package, depending on system thermal performance requirements. The
transmit design uses an Electro-Absorptive Modulated Laser (EML) which,
depending on the configuration, produces an average output power of between
-4 dBm to 2 dBm (EOL). A PIN (-17 dBm typical sensitivity) or APD (-24 dBm
typical sensitivity) receiver is available, based on system configurations.
JDSU PH1 Series transponders are designed to support the following data rates:
9.953 Gb/s (SONET), 10.3125 Gb/s (Ethernet), 10.664 Gb/s (FEC Encoded),
10.709 Gb/s FEC, or 11.09 Gb/s EFEC. They meet all applicable SONET/SDH standards.
Compliance
• Telcordia GR-253-Core
NORTH AMERICA
:
800 498-JDSU (5378)
WORLDWIDE
:
+800 5378-JDSU
WEBSITE
:
www.jdsu.com
Why can't the PC connect to GSM?
I am using GSM now and want to test the GSM function with the PC serial port. Why is there no display in the hyperterminal? I can't input any commands on the keyboard. The baud rate is set to 9600, th...
北极光 Embedded System
MSP430_PCB
...
gaochy1126 Microcontroller MCU
【Book Collection】Electronic Technology Digital Logic Fundamentals 5th Edition
Contents: 1 Introduction to Digital Logic 1.1 Digital Circuits and Digital Signals 1.2 Number Systems 1.3 Arithmetic Operations on Binary Numbers 1.4 Binary Codes 1.5 Binary Logic Variables and Basic ...
wzt Analog electronics
How to determine the start bit of com port communication?
For example, the instrument manual says the start bit is (02), so how do you determine that 2 is the start bit? ? What if there is also data 2 in the middle, for example, the data sent is: 222222222...
ewrrwe Embedded System
C2000 DSP LaunchPad expansion board (uploaded)
[i=s] This post was last edited by Pinghu Qiuyue on 2014-5-27 09:50 [/i] I asked someone to make an expansion board for C2000 LaunchPad. I will show it to you in a few days. You can do general experim...
平湖秋月 Microcontroller MCU
Why can't the kernel be started if there are bad blocks in the kernel burning area?
[table=98%,rgb(239, 245, 249)] [tr][td]Hi everyone, the address I burned the kernel to is 0x200000, but there is a bad block at 0x280000. When I boot, it prompts bad CRC and cannot find the kernel. I ...
yanghelovehuang Microchip MCU

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 847  1957  1440  2415  1224  18  40  29  49  25 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号