EEWORLDEEWORLDEEWORLD

Part Number

Search

PH1-FLALC3562

Description
Transponder, 10660Mbps(Tx), 10660Mbps(Rx), LC/SPC Connector,
CategoryWireless rf/communication    Optical fiber   
File Size240KB,6 Pages
ManufacturerLumentum Operations LLC
Download Datasheet Parametric View All

PH1-FLALC3562 Overview

Transponder, 10660Mbps(Tx), 10660Mbps(Rx), LC/SPC Connector,

PH1-FLALC3562 Parametric

Parameter NameAttribute value
MakerLumentum Operations LLC
Reach Compliance Codecompliant
Other featuresIT ALSO OPERATE FROM 1280NM TO 1600NM
body height13.2 mm
Body length or diameter84.1 mm
Connection TypeLC/SPC CONNECTOR
Data rate (receive)10660 Mbps
Data rate (send)10660 Mbps
Emitter/Detector TypeAVALANCHE PHOTODIODE
Fiber optic equipment typesTRANSCEIVER, TRANSPONDER
Nominal operating wavelength1548 nm
Nominal optical power output1.584 mW
minimum return loss-27 dB
Sensitivity-24 dBm
COMMUNICATIONS MODULES & SUBSYSTEMS
10 Gb/s TDM/DWDM 300 Pin SFF MSA SR2/IR2/LR2 Transponder
PH1 Series
Key Features
• Three configurations supporting SR2/IR2/LR2 applications
• Supports dense wavelength division multiplexing
(DWDM) applications (without wavelocker)
• Microprocessor controls to support I2C
• Integrated 16:1/1:16 mux/demux
• Small form factor package (2.2" x 3.0" x 0.53") for high
density applications
• Low power consumption: 4.8 W typical, 6.8 W maximum
for TDM applications
• 70 °C maximum operating temperature
• High sensitivity PIN or APD receivers
• SONET, FEC, Ethernet and Multirate Capable Versions
• Forward, counter and line timing clocking modes
Applications
Telecommunications
Metropolitan Area Networks
Subscriber loop
Intra-office SONET/SDH
High bit-rate data communications
JDSU 10 Gb/s PH1 Series transponders are intended for 1550 nm system
applications with reaches of up to 80 km. The series includes three different
transponders for SR2 (25 km), IR2 (40 km), and LR2 (80 km) TDM or DWDM
applications. Each transponder accepts 16 bits of parallel digital data and converts
it to a 10 Gb/s NRZ modulated optical signal. It also accepts a 10 Gb/s NRZ
modulated optical signal and converts it into 16 bit wide parallel digital data.
The PH1 series offers low DC power dissipation and is available in either a small
form factor package (2.2 x 3 x 0.53 inches) or in a larger footprint (3.5 x 4.5 x 0.53
inches) package, depending on system thermal performance requirements. The
transmit design uses an Electro-Absorptive Modulated Laser (EML) which,
depending on the configuration, produces an average output power of between
-4 dBm to 2 dBm (EOL). A PIN (-17 dBm typical sensitivity) or APD (-24 dBm
typical sensitivity) receiver is available, based on system configurations.
JDSU PH1 Series transponders are designed to support the following data rates:
9.953 Gb/s (SONET), 10.3125 Gb/s (Ethernet), 10.664 Gb/s (FEC Encoded),
10.709 Gb/s FEC, or 11.09 Gb/s EFEC. They meet all applicable SONET/SDH standards.
Compliance
• Telcordia GR-253-Core
NORTH AMERICA
:
800 498-JDSU (5378)
WORLDWIDE
:
+800 5378-JDSU
WEBSITE
:
www.jdsu.com
The reverse connection protection circuit will also be turned on. Please help me see
The reverse connection protection circuit will also be turned on. Please help me see...
dianhang Analog electronics
The subtle structure inside the battery may be the cause of the Boeing 787 fire
Investigators with the National Transportation Safety Board are analyzing whether two Boeing Co. 787 Dreamliner fires nearly a month ago that have grounded the planes are linked to the formation of ti...
qwqwqw2088 Power technology
About the initialization external bus controller of lpc2292 arm
My program is now running in external flash, LPC2292, the external flash is sst39vf1601, at the 0x10000 address of the external flash (that is, the 0x80010000 address seen by arm is the address I burn...
xianzihua888 ARM Technology
How to reduce the frequency of the simulator's test clock?
Supplement: ADS tool is used...
qwerc ARM Technology
The online learning of C2000/MSP430/power supply is not working!!!
The online learning of C2000/MSP430/power supply is not working! ! ! ! Please pay attention, does this problem occur in your place?...
zhouhua1342 Analogue and Mixed Signal
Code Error #10099-D
Hello everyone! I am using the F28M36x series DSP. When compiling in CCS, an error #10099-D appears indicating insufficient code storage capacity. Can any technical experts tell me how to solve this e...
escort DSP and ARM Processors

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 579  1702  1312  2769  2064  12  35  27  56  42 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号