MAX4578C_P/MAX4579C_P................................0°C to +70°C
MAX4578E_P/MAX4579E_P .............................-40°C to +85°C
Storage Temperature Range .............................-65°C to +160°C
Lead Temperature (soldering, 10sec) .............................+300°C
Note 1:
Signals on NO_, COM_, EN, LATCH, CAL, A_ exceeding V+ or V- are clamped by internal diodes. Limit forward current to
maximum current ratings.
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
ELECTRICAL CHARACTERISTICS—Dual ±15V Supplies
(V+ = +15V ±10%, V- = -15V ±10%, logic levels = 2.4V and 0.8V, T
I would like to ask about this half-wave precision rectifier circuit. When the input is a sine wave, the output can achieve half-wave rectification, but why does the output amplitude not become twice ...
1. If you don't like your current job, either quit or shut up. When you are new to a job, you often have high expectations but low skills, and you are arrogant. You can't do big things and don't want ...
"The fine rain wets my clothes but I cannot see it, the idle flowers fall to the ground but I hear no sound" is a line from the poem "Farewell to Yan Shiyuan" by the Tang Dynasty poet Liu Changqing. S...
In order to prevent traffic accidents, when the intelligent detection device of the car detects danger ahead, it must send a warning message to the driver. The voice alarm clearly reminds the drive...[Details]
This article discusses how to use an ultra-low-power RF transceiver chip from Zarlink Semiconductor for pacemakers, neurostimulators, drug pumps, and other such implantable medical devices to achiev...[Details]
The role of digital-to-analog converters
Real-world analog signals, such as temperature, pressure, sound, or images, are constantly being converted into digital form that is easier to store, p...[Details]
The hardware circuit principle is shown in Figure 1. In the specific design, each part should consider the anti-interference problem to minimize the impact of interference on the performance of the...[Details]
As the whole equipment is becoming increasingly miniaturized and power-saving, low-dropout linear regulators (LDOs) with low power consumption are becoming the mainstream in the market for linear regu...[Details]
There are many ways to attenuate signals. The most commonly used method is to divide the voltage using resistors. The common circuits are as follows:
Oscilloscope pre-stage attenuation c...[Details]
introduction
In engineering practice, ultrasonic waves are often used to measure distances because of their strong directivity, slow energy consumption, and long propagation distance in th...[Details]
With the continuous emergence of new technologies and the increasing complexity of DSP real-time systems, there are more and more different types of external devices. Writing drivers for these exte...[Details]
TMS320C62X is a new generation of high-performance fixed-point digital signal processor (
DSP
) chip
from Texas Instruments (
TI
). The software design problem based on
DSP
is to use...[Details]
Application of TWLA500 in ADC and related fields
FAE: On-site technical support. Provide technical support to customers on the application of the products you sell, and handle quality ...[Details]
Abstract:
This paper introduces the excitation system designed for 3/3 phase double winding induction generator, which is composed of DSP and FPGA. The interface circuit of the control sys...[Details]
Billboards are information display terminals for the public, with a wide range of civil and commercial values. However, most of the information displayed on billboards is currently solidified in th...[Details]
The PIC series 8-bit single-chip microcomputer (RISC microcontroller) developed by Microchip Technology Inc. in the United States, especially the microcontroller with built-in second-generation Flash ...[Details]
Preface
In the application of PLL, DLL and CDR circuits, people generally require the output clock signal to have a 50% duty cycle so that data can be sampled at both the rising and fallin...[Details]
The full name of RFID is Radio Frequency Identification, which uses radio frequency to realize data transmission between programmable controller (PLC) or microcomputer (PC) and identification, ther...[Details]
Analog electronics
京公网安备 11010802033920号
EEWORLD
