MIC5020
Micrel, Inc.
MIC5020
Current-Sensing Low-Side MOSFET Driver
General Description
The MIC5020 low-side MOSFET driver is designed to operate
at frequencies greater than 100kHz (5kHz PWM for 2% to
100% duty cycle) and is an ideal choice for high-speed ap-
plications such as motor control, SMPS (switch mode power
supplies), and applications using IGBTs. The MIC5020 can
also operate as a circuit breaker with or without automatic
retry. The MIC5020’s maximum supply voltage lends itself
to control applications using up to 50V. The MIC5020 can
control MOSFETs that switch voltages greater than 50V.
A rising or falling edge on the input results in a current source
or sink pulse on the gate output. This output current pulse
can turn on or off a 2000pF MOSFET in approximately 175ns.
The MIC5020 then supplies a limited current (< 2mA), if
necessary, to maintain the output state.
An overcurrent comparator with a trip voltage of 50mV makes
the MIC5020 ideal for use with a current sensing MOSFET.
An external low value resistor may be used instead of a
sensing MOSFET for more precise overcurrent control. An
optional external capacitor connected to the C
T
pin may be
used to control the current shutdown duty cycle from 20%
to < 1%. A duty cycle from 20% to about 75% is possible
with an optional pull-up resistor from C
T
to V
DD
. An open
collector output provides a fault indication when the sense
inputs are tripped.
The MIC5020 is available in 8-pin SOIC package.
Other members of the MIC502x series include the MIC5021
high-side driver and the MIC5022 half-bridge driver with a
cross-conduction interlock.
Features
•
•
•
•
•
•
•
•
•
•
•
•
•
11V to 50V operation
175ns rise/fall time driving 2000pF
TTL compatible input with internal pull-down resistor
Overcurrent limit
Fault output indication
Gate to source protection
Compatible with current sensing MOSFETs
Lamp control
Heater control
Motor control
Solenoid switching
Switch-mode power supplies
Circuit breaker
Applications
Ordering Information
Part Number
Standard
MIC5020BM
Pb-Free
MIC5020YM
Temperature
Range
–40ºC to +85ºC
Package
8-pin SOIC
Typical Application
V+
+11V to +50V
10µF
150kHz max.
1
2
3
MIC5020
V
DD
Input
Fault
C
T
Gate
Sense-
Sense+
Gnd
8
7
6
5
N-Channel
Power MOSFET
R
S E N S E =
50mV
I
TR IP
optional*
4
R
SENSE
* increases time before retry
Low-Side Driver with Overcurrent Trip and Retry
Micrel, Inc. • 2180 Fortune Drive • San Jose, CA 95131 • USA • tel + 1 (408) 944-0800 • fax + 1 (408) 474-1000 • http://www.micrel.com
July 2005
1
MIC5020
MIC5020
Micrel, Inc.
Pin Configuration
1
2
3
4
V
DD
Gate
8
Input
Sense-
7
Fault
Sense+
6
C
T
Gnd
5
SOIC Package
(M)
Block Diagram
6V Internal Regulator
I
1
C
INT
2I
1
Fault
Normal
C
T
Fault
Q1
Sense+
Sense-
50mV
↑
ONE-
↓
SHOT
ON
OFF
V
DD
6V
Input
10I
2
I
2
Gate
Transistor Count: 82
Pin Description
Pin Number
1
2
3
Pin Name
Input
Fault
V
DD
Pin Function
Supply: +11V to +50V. Decouple with ≥ 10µF capacitor.
TTL Compatible Input: Logic high turns the external MOSFET on. An internal
pull-down returns an open pin to logic low.
Overcurrent Fault Indicator: When the sense voltage exceeds threshold,
open collector output is open circuit for 5µs (t
G(ON)
), then pulled low for
t
G(OFF)
. t
G(OFF)
is adjustable from C
T
.
Retry Timing Capacitor: Controls the off time (t
G(OFF)
) of the overcurrent
retry cycle. (Duty cycle adjustment.)
• Open = 20% duty cycle.
• Capacitor to Ground = approx. 20% to <1% duty cycle.
• Pull-Up resistor = approx. 20% to approx. 75% duty cycle.
• Ground = maintained shutdown upon overcurrent condition.
4
C
T
5
6
Gnd
Sense +
Circuit Ground
Current Sense Comparator (+) Input: Connect to high side of sense resistor
or current sensing MOSFET sense lead. A built-in offset in conjunction with
R
SENSE
sets the load overcurrent trip point.
Current Sense Comparator (–) Input: Connect to the low side of the sense
resistor (usually power ground).
7
8
Sense –
Gate
Gate Drive: Drives the gate of an external power MOSFET. Also limits V
GS
to 15V max. to prevent Gate to Source damage. Will sink and source
current.
MIC5020
2
July 2005
MIC5020
Micrel, Inc.
Absolute Maximum Ratings
Supply Voltage (V
DD
)................................................... +55V
Input Voltage .................................................–0.5V to +15V
Sense Differential Voltage .......................................... ±6.5V
Sense + or Sense – to Gnd ...........................–0.5V to +50V
Fault Voltage ............................................................... +50V
Current into Fault ........................................................ 50mA
Timer Voltage (C
T
) ...................................................... +5.5V
Operating Ratings
Supply Voltage (V
DD
)......................................+11V to +50V
Temperature Range
SOIC ....................................................... –40°C to +85°C
Electrical Characteristics
Symbol
Parameter
D.C. Supply Current
T
A
= 25°C, Gnd = 0V, V
DD
= 12V, Sense +,– = 0V, Fault = Open, C
T
= Open, Gate C
L
= 1500pF unless otherwise specificed
Condition
V
DD
= 12V, Input = 0V
V
DD
= 50V, Input = 0V
V
DD
= 12V, Input = 5V
Input Threshold
Input Hysteresis
Input Pull-Down Current
Fault Output
Saturation Voltage
Fault Output Leakage
Current Limit Threshold
Gate On Voltage
t
G(ON)
t
DLH
t
R
t
F
t
DLH
f
max
Note 1
Note 2
Note 3
Note 4
Note 5
Note 6
Note 7
Min
Typ
0.8
2
0.8
4
Max
2
10
2
25
2.0
40
0.4
+1
70
18
10
50
800
1500
1500
1500
Units
mA
mA
mA
mA
V
V
µA
V
µA
mV
V
V
µs
µs
ns
ns
ns
ns
kHz
V
DD
= 50V, Input = 5V
0.8
10
1.4
0.1
20
0.15
Input = 5V
Fault Current = 1.6mA
Note 1
Fault = 50V
Note 2
V
DD
= 50V
V
DD
= 12V
Sense Differential > 70mV
–1
30
10
14
2
10
0.01
50
11
15
5
20
400
700
900
500
Gate On Time, Fixed
Gate Off Time, Adjustable
Gate Turn-On Delay
Gate Rise Time
Gate Turn-Off Delay
Gate Fall Time
Maximum Operating Frequency
Voltage remains low for time affected by C
T
.
t
G(OFF)
Sense Differential > 70mV, C
T
= 0pF
Note 3
Note 4
Note 5
Note 6
Note 7
100
150
When using sense MOSFETs, it is recommended that R
SENSE
< 50Ω. Higher values may affect the sense MOSFET’s current transfer ratio.
Input switched from 0.8V (TTL low) to 2.0V (TTL high), time for Gate transition from 0V to 2V.
Input switched from 0.8V (TTL low) to 2.0V (TTL high), time for Gate transition from 2V to 10V.
Input switched from 2.0V (TTL high) to 0.8V (TTL low), time for Gate transition from 11V (Gate ON voltage) to 10V.
Input switched from 2.0V (TTL high) to 0.8V (TTL low), time for Gate transition from 10V from 2V.
Frequency where gate on voltage reduces to 10V with 50% input duty cycle.
July 2005
3
MIC5020
MIC5020
Micrel, Inc.
Typical Characteristics
Supply Current vs.
Supply Voltage
V
IN
= 5V
3.5
3.0
I
SUPPLY
(mA)
900
800
t
ON
(nS)
Turn-On Time vs.
Supply Voltage
V
G AT E
= 4V
C
L
= 1500pF
V
IN
= 0 to 5V Sq. Wave
1200
1100
t
OFF
(ns)
Turn-Off Time vs.
Supply Voltage
2.5
2.0
1.5
1.0
0.5
700
600
500
INCLUDES PROPAGATION DELAY
1000
900
800
V
G AT E
= 4V
C
L
= 1500pF
V
IN
= 0 to 5V
Sq. Wave
INCLUDES PROPAGATION DALAY
V
IN
= 0V
5 10 15 20 25 30 35 40 45 50
V
SUPPLY
(V)
400
700
5 10 15 20 25 30 35 40 45 50
V
SUPPLY
(V)
5
10
15
20
V
SUPPLY
(V)
25
30
100
80
I
IN
(µA)
Input Current vs.
Input Voltage
V
SUPPLY
= 12V
1200
1000
Turn-On Time vs.
Gate Capacitance
V
G AT E
= 4V
25.0
Shutdown Duty Cycle (%)
Overcurrent Shutdown
Retry Duty Cycle
t
ON
= 5µs
V
SUPPLY
= 12V
20.0
15.0
10.0
5.0
0.0
0.1
t
ON
(ns)
60
40
20
0
800
600
400
INCLUDES PROPAGATION DELAY
0
5
10
15
V
IN
(V)
20
25
200
1x10
2
1x10
3
1x10
4
C
GATE
(pF)
1x10
5
1
10
100
C
T
(pF)
1000 10000
80
70
VOLTAGE (mV)
60
50
40
30
Sense Threshold vs.
Temperature
Input
Gate
TTL (H)
0V
15V (max.)
Sense +,
–
Differential
Fault
0V
50mV
0V
Off
On
20
-60 -30 0 30 60 90 120 150
TEMPERATURE (°C)
Timing Diagram 1. Normal Operation
5µs
20µs
Input
Gate
TTL (H)
0V
15V (max.)
5µs
Input
Gate
TTL (H)
0V
15V (max.)
Sense +,–
Differential
Fault
0V
50mV
0V
Off
On
Sense +,–
Differential
Fault
0V
50mV
0V
Off
On
Timing Diagram 2. Fault Condition, C
T
= Open
MIC5020
4
Timing Diagram 3. Fault Condition, C
T
= Grounded
July 2005
MIC5020
Micrel, Inc.
MOSFET Q1.
A fault condition (> 50mV from
SENSE
+
to
SENSE
–)
causes
the overcurrent comparator to enable current sink 2I
1
which
overcomes current source I
1
to discharge C
INT
in a short time.
When C
INT
is discharged, the
INPUT
is disabled, which turns
off the
GATE
output; the
FAULT
output is enabled; and C
INT
and C
T
are ready to be charged.
When the
GATE
output turns the MOSFET off, the overcurrent
signal is removed from the sense inputs which deactivates
current sink 2I
1
. This allows C
INT
and the optional capacitor
connected to C
T
to recharge. A Schmitt trigger delays the
retry while the capacitor(s) recharge. Retry delay is increased
by connecting a capacitor to C
T
(optional).
Functional Description
Refer to the MIC5020 block diagram.
Input
A signal greater than 1.4V (nominal) applied to the MIC5020
INPUT
causes gate enhancement on an external MOSFET
turning the external MOSFET on.
An internal pull-down resistor insures that an open
INPUT
remains low, keeping the external MOSFET turned off.
Gate Output
Rapid rise and fall times on the
GATE
output are possible
because each input state change triggers a one-shot which
activates a high-value current sink (10I
2
) for a short time.
This draws a high current through a current mirror circuit
causing the output transistors to quickly charge or discharge
the external MOSFET’s gate.
A second current sink continuously draws the lower value
of current used to maintain the gate voltage for the selected
state.
An internal 15V Zener diode protects the external MOSFET
by limiting the gate output voltage when V
DD
is connected
to higher voltages.
Overcurrent Limiting
Current source I
1
charges C
INT
upon power up. An optional
external capacitor connected to C
T
is discharged through
The retry cycle will continue until the the fault is removed or
the input is changed to TTL low.
If C
T
is connected to ground, the circuit will not retry upon a
fault condition.
Fault Output
The
FAULT
output is an open collector transistor.
FAULT
is
active at approximately the same time the output is disabled
by a fault condition (5µs after an overcurrent condition is
sensed). The
FAULT
output is open circuit (off) during each
successive retry (5µs).
Applications Information
The MIC5020 MOSFET driver is intended for low-side switch-
ing applications where higher supply voltage, overcurrent
sensing, and moderate speed are required.
Supply Voltage
A feature of the MIC5020 is that its supply voltage rating of
up to 50V is higher than many other low-side drivers.
The minimum supply voltage required to fully enhance an
N-channel MOSFET is 11V.
A lower supply voltage may be used with logic level MOS-
FETs. Approximately 6V is needed to provide 5V of gate
enhancement.
Low-Side Switch Circuit Advantages
A moderate-speed low-side driver is generally much faster
than a comparable high-side driver. The MIC5020 can pro-
vide the gate drive switching times and low propagation delay
times that are necessary for high-frequency high-efficiency
circuit operation in PWM (pulse width modulation) designs
used for motor control, SMPS (switch mode power supply)
and heating element control. Switched loads (on/off) can
benefit from the MIC5020’s fast switching times by allowing
use of MOSFETs with smaller safe operating areas. (Larger
MOSFETs are often required when using slower drivers.)
Overcurrent Limiting
A 50mV comparator is provided for current sensing. The low
level trip point minimizes I
2
R losses when power resistors
are used for current sensing. Flexibility in choosing drain or
source side sensing is provided by access to both
SENSE
+
and
SENSE
–
comparator inputs.
The adjustable retry feature can be used to handle loads
with high initial currents, such as lamps, motors, or heating
elements and can be adjusted from the C
T
connection.
C
T
to ground causes maintained gate drive shutdown follow-
ing overcurrent detection.
C
T
open, or through a capacitor to ground, causes automatic
retry . The default duty cycle (C
T
open) is approximately
20%. Refer to the electrical characteristics when selecting
a capacitor for a reduced duty cycle.
C
T
through a pull-up resistor to V
DD
increases the duty cycle.
Increasing the duty cycle increases the power dissipation in
the load and MOSFET.
Circuits may become unstable at a
duty cycles of about 75% or higher, depending on the condi-
tions.
Caution: The MIC5020 may be damaged if the voltage
on C
T
exceeds the absolute maximum rating.
An overcurrent condition is externally signaled by an open
collector (
FAULT
) output.
The MIC5020 may be used without current sensing by con-
necting
SENSE
+
and
SENSE
–
to ground.
Current Sense Resistors
Lead length can be significant when using low value (< 1Ω)
resistors for current sensing. Errors caused by lead length
can be avoided by using four-terminal current sensing re-
sistors. Four-terminal resistors are available from several
manufacturers.
July 2005
5
MIC5020
京公网安备 11010802033920号
EEWORLD
