• FCC Part 68, UL 1459, Bellcore 1089 & ITU-K.20/K.21 Compliant
• UL File Recognition #E208219
• Peak Off-State Voltage from 25 to 300 Volts
• Surge Current Capability (See Table 1)
• ESD Protection > 25 kilovolts
• Low Capacitance for T1/E1 Trunk & Line Card Applications
• Bidirectional Configuration
• RoHS Compliant
• REACH Compliant
APPliCATionS
•
•
•
•
•
•
T1/E1 Trunk & Line Cards
SLIC Line Card
DBX Branch Exchange Switches
FCC Part 68 Customer Premise Equipment
Line Interface Modem
xDSL Architecture Interface
meChAniCAl ChARACTeRiSTiCS
Molded Plastic DO-214AA Package
Approximate Weight: 2.5 grams
Lead-Free Pure-Tin Plating (Annealed)
Solder Reflow Temperature:
Pure-Tin - Sn, 100: 260-270°C
• Flammability Rating UL 94V-0
• 12mm Tape and Reel per EIA Standard 481
•
•
•
•
DEVICE SYMBOL
BIDIRECTIONAL
TAble 1 - SuRge RATingS
SeRieS
i
PP
2/10µs
AmPS
150
300
500
i
PP
8/20µs
AmPS
150
300
400
i
PP
10/160µs
AmPS
100
150
200
i
PP
10/560µs
AmPS
50
100
200
i
PP
10/1000µs
AmPS
50
80
100
i
TSm
60hz
AmPS
20
32
60
di/dt
A/µs
(note 1)
500
500
500
dv/dt
V/µs
(note 1)
2000
2000
2000
SA
SB
SC
noTeS
1. Critical rate of rise for On-State Current (di/dt) and Off-State Voltage (dv/dt).
05081.R11 2/11
Page 1
www.protekdevices.com
05081
Only One Name Means ProTek’Tion™
PP0640SA - PP3500SC
TyPiCAl DeViCe ChARACTeRiSTiCS
mAXimum RATingS
@ 25°C unless otherwise Specified
PARAmeTeR
Surge Current - 50/60Hz (SC Series)
Junction Temperature
Storage Temperature
Thermal Resistance (Junction) - SA & SB Series
Thermal Resistance (Junction) - SC Series
Thermal Resistance (Ambient) - SA & SB Series
Thermal Resistance (Ambient) - SC Series
Symbol
I
TSM
T
A
T
STG
R
QJC
R
QJC
R
QJA
R
QJA
VAlue
60
-40 to 150
-55 to 150
28
26
90
85
uniTS
Amps
°C
°C
°C/Watt
°C/Watt
°C/Watt
°C/Watt
FiguRe 1
PulSe WAVeFoRm
t
f
i
PP
- Peak Pulse Current - % of i
PP
100
FiguRe 2
Vi ChARACTeRiSiTC CuRVe
TEST
WAVEFORM
PARAMETERS
t
f
= 10µs
t
d
= 1000µs
I
PP
I
TSM
I
T
I
S
I
H
V
S
I
DRM
V
T
V
DRM
Peak Value I
PP
t
d
= t/(I
PP
/2)
50
e
-t
0
0
1
t - Time - ms
2
3
100
non-Repetitive on-State Current (i
TSm
) - Amps
FiguRe 3
on-STATe CuRRenT VS SuRge CuRRenT DuRATion
PPxxxxSA
PPxxxxSC
10
PPxxxxSB
1
1
10
100
Surge Current Duration - Full Cycles
Supply Frequency - 60 hz Sinusoidal
Page 2
1000
05081.R11 2/11
www.protekdevices.com
05081
Only One Name Means ProTek’Tion™
PP0640SA - PP3500SC
TyPiCAl DeViCe ChARACTeRiSTiCS
eleCTRiCAl ChARACTeRiSTiCS PeR line
@ 25°C unless otherwise Specified
PART
numbeR
DeViCe
mARking
RePeTiTiVe SWiTChing minimum SWiTChing mAXimum
PeAk
VolTAge
holDing
CuRRenT
oFF-STATe
CuRRenT
CuRRenT
oFF-STATe
VolTAge
(Fig. 7)
(Fig. 4)
@100V/µs di/dt = 1A/ms
@V
DRm
V
DRm
V
S
i
h
iS
i
DRm
VolTS
VolTS
mA
mA
µA
58
65
75
90
120
140
160
190
220
275
300
25
58
65
75
90
120
140
160
190
220
275
300
58
65
75
90
120
140
160
190
220
275
300
77
88
98
130
160
180
220
260
300
350
400
40
77
88
98
130
160
180
220
260
300
350
400
77
88
98
130
160
180
220
260
300
350
400
150
150
150
150
150
150
150
150
150
150
150
50
150
150
150
150
150
150
150
150
150
150
150
150
150
150
150
150
150
150
150
150
150
150
800
800
800
800
800
800
800
800
800
800
800
800
800
800
800
800
800
800
800
800
800
800
800
800
800
800
800
800
800
800
800
800
800
800
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
mAXimum
on-STATe
VolTAge
(Fig. 5)
@i
T
V
T
VolTS
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
on-STATe
CuRRenT
TyPiCAl
CAPACiTAnCe
(note 1)
@2V, 1mhz
C
pF
60
60
60
60
40
40
40
30
30
30
30
110
60
60
60
60
40
40
40
30
30
30
30
120
120
120
120
80
80
80
60
60
60
60
i
T
AmPS
2.2
2.2
2.2
2.2
2.2
2.2
2.2
2.2
2.2
2.2
2.2
2.2
2.2
2.2
2.2
2.2
2.2
2.2
2.2
2.2
2.2
2.2
2.2
2.2
2.2
2.2
2.2
2.2
2.2
2.2
2.2
2.2
2.2
2.2
PP0640SA
PP0720SA
PP0800SA
PP1100SA
PP1300SA
PP1500SA
PP1800SA
PP2300SA
PP2600SA
PP3100SA
PP3500SA
PP0300SB
PP0640SB
PP0720SB
PP0800SB
PP1100SB
PP1300SB
PP1500SB
PP1800SB
PP2300SB
PP2600SB
PP3100SB
PP3500SB
PP0640SC
PP0720SC
PP0800SC
PP1100SC
PP1300SC
PP1500SC
PP1800SC
PP2300SC
PP2600SC
PP3100SC
PP3500SC
GC
GD
GE
GF
GG
GH
GI
GJ
GK
GL
GM
GN
GP
GQ
GR
GS
GT
GU
GV
GW
GX
GY
GZ
HC
HD
HE
HF
HG
HH
HI
HJ
HK
HL
HM
1. Capacitance imblance between positive and negative polarities is typically < 15pF.
05081.R11 2/11
Page 3
www.protekdevices.com
noTeS
05081
Only One Name Means ProTek’Tion™
PP0640SA - PP3500SC
TyPiCAl DeViCe ChARACTeRiSTiCS
FiguRe 4
TyPiCAl PeAk oFF-STATe CuRRenT
VS junCTion TemPeRATuRe
FiguRe 5
TyPiCAl PeAk on-STATe CuRRenT
VS on-STATe VolTAge
10
i
DRm
- Peak off-State Current - µA
100
1
i
T
- on-State Current - A
0
40
80
t
A
- Temperature - °C
120
10
0.1
0.01
-40
1
0
1
2
3
4
5
V
T
- on-State Voltage - V
6
7
FiguRe 6
TyPiCAl noRmAlizeD SWiTChing VolTAge
VS junCTion TemPeRATuRe
1.10
normalized V
S
normalized i
h
FiguRe 7
TyPiCAl noRmAlizeD holDing CuRRenT
VS junCTion TemPeRATuRe
2
1
1
0.9
0.8
-40
0
40
80
t
A
- Temperature - °C
120
0
-40
0
40
80
t
A
- Temperature - °C
120
05081.R11 2/11
Page 4
www.protekdevices.com
05081
Only One Name Means ProTek’Tion™
PP0640SA - PP3500SC
APPliCATion inFoRmATion
FiguRe 1 - ul 1459 & FCC PART 68 meTAlliC PRoTeCTion
The TSS (Thyristor Surge Suppressor) device is located across the tip-to-ring after a limiting resistor and fuse combination. RTIP and RRING resistors are optional de-
pending upon the TSS device selection. Without the resistors, the PP3100SB/SC is recommended. However, with a resistance value of 7.5 Ohms for tip and ring, the
PP3100SA is recommended. Digital signals may use a lower TSS device depending upon the total tip to ring voltage range. Selection of the TSS device, either PPxxxx-
SA or SB/SC is based upon the value of the tip and ring resistors. For the National Electric Code (NEC) article 800, it is recommended that at least one fuse be used in
the tip or ring line for metallic surges. Fuses may be replaced with a suitable Positive Temperature Coefficient (PTC) automatic resettable current limiting device.
TIP
Fuse
R
Tip
To Protected
Equipment
RING
R
Ring
FiguRe 2 - ul 1459 & FCC PART 68 longiTuDinAl PRoTeCTion
There are two TSS devices, one located from tip-to-ground and one ring-to-ground. For standard analog signals, the PP3100SA is recommended with a typical resistor
value for tip and ring of 15 Ohms. The PP3100SB/SC is recommended for resistor values of 7.5 Ohms each. The National Electric Code (NEC) article 800 requires two
fuse elements when connecting to ground. Fuses or a suitable Positive Temperature Coefficient (PTC) automatic resettable current limiting device may be used. The
purpose of this circuit is to limit AC power current from getting on the ground line causing any safety hazard.
By: Arthur Pini, Lawrence Jacobs Recently, a reader asked, "Why do oscilloscope manufacturers put the amplifier at the probe tip instead of inside the oscilloscope?" Putting the amplifier in the probe...
[align=center][b][font=宋体][size=22pt]Vibration alarm device based on LPC1343 and three-axis acceleration sensor[/size][/font][/b][/align] [align=center][b][font=宋体][size=22pt][/size][/font][/b][/align...
I am used to working overtime, although I cannot say that I work overtime for myself... Of course, I arrive at the company late in the morning, and basically come in around 10:30 every day. However, i...
#pragma dataseg = DATA __no_init uint16 StackCheck @ 0x350; #pragma dataseg = defaultWhat does the above sentence mean? I hope you can help me. If you have any information, please send it to me.:)...
[size=4] AC coupling (AC COUPLED) is achieved by connecting capacitors in series in the circuit. The type of capacitor is not limited. The function of AC coupling is to remove the DC component in the ...
China's new energy vehicles are in a transition period from research and development to real industrial development. In 2012, with the intensive launch of new energy vehicle policy planning, the de...[Details]
The Mobile Industry Processor Interface (MIPI) Alliance is an organization responsible for promoting the standardization of software and hardware in mobile devices. It has released the D-PHY specif...[Details]
When choosing a laptop battery, you should consider several factors, such as power, appearance, and quality.
Regarding power, we often see that a manufacturer uses values such as the number ...[Details]
introduction
The emergence of high-performance, low-power embedded CPUs and high-reliability network operating systems has made it possible to implement applications with large amounts of comp...[Details]
1 Introduction
Ultrasonic waves have strong directivity, slow energy consumption, and can propagate over long distances in a medium, so they are used for distance measurement. Ultrasonic detec...[Details]
1 Introduction
Water resources are the basic conditions for human survival and the lifeline of economic development. The reality shows that due to the global shortage of water resources and th...[Details]
On the afternoon of July 10, Beijing time, Taiwan's largest chip designer MediaTek expects its smartphone chip shipments to grow by double digits in the third quarter of this year, and the company is ...[Details]
Investment in
the
medical device
industry has been on the rise in recent years. In the past two years, venture capital for medical devices has almost doubled, reaching $4 billion in 2007. Fr...[Details]
Continuity test
A variety of devices need to be checked for continuity, including cable assemblies, printed circuit boards, and connectors to ensure that these components have the expected contin...[Details]
Abstract: With the development and construction of BeiDou II system, China will shift from the situation dominated by GPS to the situation dominated by BeiDou II global navigation system independen...[Details]
Recently, news came from the certification department that the photovoltaic grid-connected inverter of Samil New Energy Co., Ltd. (hereinafter referred to as "Samil New Energy") has once again obta...[Details]
LED lighting: Basic circuit design can be completed in as little as one day
Semiconductor manufacturers are also getting involved in the LED lighting business. The power circuit of LED req...[Details]
The ARINC429 bus is one of the most commonly used communication buses between various subsystems of avionics. As the "skeleton" of modern avionics systems, once the bus system or the attached airbo...[Details]
0 Introduction
In order to improve the automation control of shortwave transmitters, so that they can automatically process from far to near, the technicians here use the ICS system to complete the ...[Details]
Analogue and Mixed Signal
京公网安备 11010802033920号
EEWORLD
