EEWORLDEEWORLDEEWORLD

Part Number

Search

L-714SRDT

Description
SINGLE COLOR LED, SUPER BRIGHT RED, 3mm, 3 X 3 MM, ROHS COMPLIANT PACKAGE-2
CategoryLED optoelectronic/LED    photoelectric   
File Size89KB,3 Pages
ManufacturerKingbright
Websitehttp://www.us.kingbright.com
Environmental Compliance
Download Datasheet Parametric View All

L-714SRDT Overview

SINGLE COLOR LED, SUPER BRIGHT RED, 3mm, 3 X 3 MM, ROHS COMPLIANT PACKAGE-2

L-714SRDT Parametric

Parameter NameAttribute value
Is it Rohs certified?conform to
MakerKingbright
package instruction3 X 3 MM, ROHS COMPLIANT PACKAGE-2
Reach Compliance Codecompliant
ECCN codeEAR99
colorSUPER BRIGHT RED
ConfigurationSINGLE
Maximum forward current0.03 A
Lens typeDIFFUSED RED
Nominal luminous intensity70.0 mcd
Installation featuresRADIAL MOUNT
Number of functions1
Number of terminals2
Maximum operating temperature85 °C
Minimum operating temperature-40 °C
Optoelectronic device typesSINGLE COLOR LED
total height4.8 mm
method of packingBULK
peak wavelength660 nm
shapeSQUARE
size3 mm
surface mountNO
Terminal pitch2.54 mm
perspective110 deg

L-714SRDT Preview

3x3mm SQUARE TOP LED LAMP
L-714SRDT
SUPER BRIGHT RED
Features
LOW POWER CONSUMPTION.
ULTRA BRIGHTNESS AVAILABLE.
WIDE VIEWING ANGLE.
RELIABLE AND RUGGED.
EXCELLENT UNIFORMITY OF LIGHT OUTPUT.
IDEAL FOR FLUSH MOUNTED PANEL INDICATORS.
RoHS COMPLIANT.
Description
The Super Bright Red source color devices are made with
Gallium Aluminum Arsenide Red Light Emitting Diode.
Package Dimensions
Notes:
1. All dimensions are in millimeters (inches).
2. Tolerance is
±0.25(0.01")
unless otherwise noted.
3. Lead spacing is measured where the leads emerge from the package.
4. Specifications are subject to change without notice.
SPEC NO.: DSAC2647
.
APPROVED: J. Lu
REV NO.: V.3
.
CHECKED: Allen Liu
DATE: MAR/21/2005
DRAWN: S.M.TANG
PAGE: 1 OF 3
Selection Guide
Part No.
Dice
Lens Type
Iv (mcd)
@ 20mA
Min.
L-714SRDT
SUPER BRIGHT RED (GaAIAs)
RED DIFFUSED
36
Typ.
70
Viewing
Angle
2
θ
1/2
110
°
Note:
1.
θ1/2
is the angle from optical centerline where the luminous intensity is 1/2 the optical centerline value.
Electrical / Optical Characteristics at T
A
=25°C
Symbol
λpeak
λD
∆λ1/2
C
V
F
I
R
Parameter
Peak Wavelength
Dominant Wavelength
Spectral Line Half-width
Capacitance
Forward Voltage
Reverse Current
Device
Super Bright Red
Super Bright Red
Super Bright Red
Super Bright Red
Super Bright Red
Super Bright Red
Typ.
660
640
20
45
1.85
2.5
10
Max.
Units
nm
nm
nm
pF
V
uA
Test Conditions
I
F
=20mA
I
F
=20mA
I
F
=20mA
V
F
=0V;f=1MHz
I
F
=20mA
V
R
= 5V
Absolute Maximum Ratings at T
A
=25°C
Parameter
Power dissipation
DC Forward Current
Peak Forward Current [1]
Reverse Voltage
Operating/Storage Temperature
Lead Solder Temperature [2]
Lead Solder Temperature [3]
Notes:
1. 1/10 Duty Cycle, 0.1ms Pulse Width.
2. 2mm below package base.
3. 5mm below package base.
Super Bright Red
100
30
155
5
-40°C To +85°C
260°C For 3 Seconds
260°C For 5 Seconds
Units
mW
mA
mA
V
SPEC NO.: DSAC2647
.
APPROVED: J. Lu
REV NO.: V.3
.
CHECKED: Allen Liu
DATE: MAR/21/2005
DRAWN: S.M.TANG
PAGE: 2 OF 3
Super Bright Red
L-714SRDT
Remarks:
If special sorting is required (e.g. binning based on forward voltage, luminous intensity, or wavelength),
the typical accuracy of the sorting process is as follows:
1. Wavelength: +/-1nm
2. Luminous Intensity: +/-15%
3. Forward Voltage: +/-0.1V
Note: Accuracy may depend on the sorting parameters.
SPEC NO.: DSAC2647
.
APPROVED: J. Lu
REV NO.: V.3
.
CHECKED: Allen Liu
DATE: MAR/21/2005
DRAWN: S.M.TANG
PAGE: 3 OF 3
Statement about this project!
Statement about this project 1. This project is just to learn the jtag protocol and make a jtag downloader (debugger). 2. This project is just to learn the basics of jtag, please bypass it if you are ...
paulhyde Integrated technical exchanges
Filter function judgment
Determine what function the signal output in the figure implements (high pass, low pass, band pass, etc.) Uo1 is low pass, Uo2 is band pass, Uo3 is band pass; how do you tell? It's a bit hard to tell...
1nnocent Analog electronics
Solar powered circular aircraft
[img]http://www.diytd.com/uploadfile/20070410140756724.jpg[/img] The "Solar Circular Plane" I designed and made uses solar energy as its energy source to simulate an airplane flying around the earth i...
yuandayuan6999 Energy Infrastructure?
I would like to ask how to store the data received by the STM32 DMA serial port into an array and then send it out through the serial port. Thank you.
int main(void) {SysTick_Config(SystemCoreClock/1000);LCD_Port_Init(115200);while(1){if(RxOverFlag2 = 1){USART_SendString2(USART_RXBUF);USART_SendString3(buzzer);}} }/*函数名称:DMA_Configuration2函数用途:STM32...
小子不乖1229 Embedded System
Can anyone recommend some good tutorials?
rt...
瓜妞妞 Embedded System
I recently made a PCB and used PADS to simulate it, but the actual board didn't look good.
I recently made a PCB and used PADS to simulate it. The actual board effect is not good. I will find a more accurate simulator....
kata PCB Design

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2868  658  2683  1794  2632  58  14  55  37  53 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号