2.5V / 3.3V 10-BIT ACTIVE HIGH AND LOW ENABLE, HIGH BANDWIDTH BUS SWITCH
INDUSTRIAL TEMPERATURE RANGE
QUICKSWITCH
®
PRODUCTS
2.5V / 3.3V 10-BIT HIGH AND LOW EN-
ABLE, HIGH BANDWIDTH BUS SWITCH
FEATURES:
DESCRIPTION:
IDTQS3VH862
• N channel FET switches with no parasitic diode to V
CC
– Isolation under power-off conditions
– No DC path to V
CC
or GND
– 5V tolerant in OFF and ON state
• 5V tolerant I/Os
• Low R
ON
- 4Ω typical
Ω
• Flat R
ON
characteristics over operating range
• Rail-to-rail switching 0 - 5V
• Bidirectional dataflow with near-zero delay: no added ground
bounce
• Excellent R
ON
matching between channels
• V
CC
operation: 2.3V to 3.6V
• High bandwidth - up to 500MHz
• LVTTL-compatible control Inputs
• Undershoot Clamp Diodes on all switch and control Inputs
• Low I/O capacitance, 4pF typical
• Available in QSOP package
The QS3VH862 HotSwitch with 10-bit active high and low enable is
a high bandwidth bus switch. The QS3VH862 has very low ON
resistance, resulting in under 250ps propagation delay through the
switch. The switches are controlled by independent active low enable
(BE) and active high enable (BE) controls. In the ON state, the switches
can pass signals up to 5V. In the OFF state, the switches offer very high
impedence at the terminals.
The combination of near-zero propagation delay, high OFF imped-
ance, and over-voltage tolerance makes the QS3VH862 ideal for high
performance communications applications.
The QS3VH862 is characterized for operation from -40°C to +85°C.
APPLICATIONS:
•
•
•
•
•
Hot-swapping
10/100 Base-T, Ethernet LAN switch
Low distortion analog switch
Replaces mechanical relay
ATM 25/155 switching
FUNCTIONAL BLOCK DIAGRAM
A
0
B
0
A
9
B
9
BE
BE
The IDT logo is a registered trademark of Integrated Device Technology, Inc.
INDUSTRIAL TEMPERATURE RANGE
1
c 2014 Integrated Device Technology, Inc.
FEBRUARY 2014
DSC-5859/13
IDTQS3VH862
2.5V / 3.3V 10-BIT ACTIVE HIGH AND LOW ENABLE, HIGH BANDWIDTH BUS SWITCH
INDUSTRIAL TEMPERATURE RANGE
PIN CONFIGURATION
BE
A
0
A
1
A
2
A
3
A
4
A
5
A
6
A
7
A
8
A
9
GND
1
2
3
4
5
6
7
8
9
10
11
12
24
23
22
21
20
19
18
17
16
15
14
13
V
CC
BE
B
0
B
1
B
2
B
3
B
4
B
5
B
6
B
7
B
8
B
9
ABSOLUTE MAXIMUM RATINGS
(1)
Symbol
Description
Max
V
TERM
(2)
SupplyVoltage to Ground
V
TERM
(3)
DC Switch Voltage V
S
V
TERM
(3)
DC Input Voltage V
IN
V
AC
I
OUT
T
STG
AC Input Voltage (pulse width
≤20ns)
DC Output Current (max. sink current/pin)
Storage Temperature
–0.5 to +4.6
–0.5 to +5.5
–0.5 to +5.5
–3
120
–65 to +150
Unit
V
V
V
V
mA
°C
NOTES:
1. Stresses greater than those listed under ABSOLUTE MAXIMUM RATINGS may cause
permanent damage to the device. This is a stress rating only and functional operation of
the device at these or any other conditions above those indicated in the operational
sections of this specification is not implied. Exposure to absolute maximum rating
conditions for extended periods may affect reliability.
2. V
CC
terminals.
3. All terminals except V
CC
.
0V)
Symbol
C
IN
C
I/O
CAPACITANCE
Parameter
Control Inputs
(1)
(T
A
= +25°C, F = 1MHz, V
IN
= 0V, V
OUT
=
Typ.
3
4
8
Max.
5
6
12
Unit
pF
pF
pF
Quickswitch Channels (Switch OFF)
Quickswitch Channels (Switch ON)
QSOP
TOP VIEW
C
I/O
NOTE:
1. This parameter is guaranteed but not production tested.
PIN DESCRIPTION
Pin Names
BE
BE
A
0
- A
9
B
0
- B
9
Description
Active HIGH Bus Enable
Active LOW Bus Enable
Bus A
Bus B
FUNCTION TABLE
(1)
BE
L
L
H
H
BE
L
H
L
H
A
0
- A
9
Z
Z
B
0
- B
9
Z
Function
Disconnect
Disconnect
Connect
Disconnect
NOTE:
1. H = HIGH Voltage Level
L = LOW Voltage Level
Z = High-Impedence
2
IDTQS3VH862
2.5V / 3.3V 10-BIT ACTIVE HIGH AND LOW ENABLE, HIGH BANDWIDTH BUS SWITCH
INDUSTRIAL TEMPERATURE RANGE
DC ELECTRICAL CHARACTERISTICS OVER OPERATING RANGE
Following Conditions Apply Unless Otherwise Specified:
Industrial: T
A
= –40°C to +85°C, V
CC
= 3.3V ±0.3V
Symbol
V
IH
V
IL
I
IN
I
OZ
I
OFF
R
ON
Parameter
Input HIGH Voltage
Input LOW Voltage
Input Leakage Current (Control Inputs)
Off-State Current (Hi-Z)
Data Input/Output Power Off Leakage
Switch ON Resistance
for Control Inputs
Guaranteed Logic LOW
for Control Inputs
0V
≤
V
IN
≤
V
CC
0V
≤
V
OUT
≤
5V, Switches OFF
V
IN
or V
OUT
0V to 5V, V
CC
= 0V
V
CC
= 2.3V
Typical at V
CC
= 2.5V
V
CC
= 3V
NOTE:
1. Typical values are at V
CC
= 3.3V and T
A
= 25°C.
Test Conditions
Guaranteed Logic HIGH
V
CC
= 2.3V to 2.7V
V
CC
= 2.7V to 3.6V
V
CC
= 2.3V to 2.7V
V
CC
= 2.7V to 3.6V
Min.
1.7
2
—
—
—
—
—
Typ.
(1)
Max.
—
—
—
—
—
—
—
6
7
4
5
—
—
0.7
0.8
±1
±1
±1
8
9
6
8
Unit
V
V
μA
μA
μA
Ω
V
IN
= 0V
V
IN
= 1.7V
V
IN
= 0V
V
IN
= 2.4V
I
ON
= 30mA
I
ON
= 15mA
I
ON
= 30mA
I
ON
= 15mA
—
—
—
—
TYPICAL ON RESISTANCE vs V
IN
AT V
CC
= 3.3V
16
14
R
ON
(ohms)
12
10
8
6
4
2
0
0.0
0.5
1.0
1.5
2.0
2.5
3.0
3.5
4.0
4.5
5.0
V
IN
(Volts)
3
IDTQS3VH862
2.5V / 3.3V 10-BIT ACTIVE HIGH AND LOW ENABLE, HIGH BANDWIDTH BUS SWITCH
INDUSTRIAL TEMPERATURE RANGE
POWER SUPPLY CHARACTERISTICS
Symbol
I
CCQ
ΔI
CC
I
CCD
Parameter
Quiescent Power Supply Current
Power Supply Current
(2,3)
per Input HIGH
Dynamic Power Supply Current
(4)
Test Conditions
(1)
V
CC
= Max., V
IN
= GND or V
CC
, f = 0
V
CC
= Max., V
IN
= 3V, f = 0 per Control Input
V
CC
= 3.3V, A and B Pins Open, Control Inputs
Toggling @ 50% Duty Cycle
Min.
—
—
Typ.
2
—
Max.
4
30
Unit
mA
μA
See Typical I
CCD
vs Enable Frequency graph below
NOTES:
1. For conditions shown as Min. or Max., use the appropriate values specified under DC Electrical Characteristics.
2. Per input driven at the specified level. A and B pins do not contribute to
ΔIcc.
3. This parameter is guaranteed but not tested.
4. This parameter represents the current required to switch internal capacitance at the specified frequency. The A and B inputs do not contribute to the Dynamic Power Supply Current. This
parameter is guaranteed but not production tested.
TYPICAL I
CCD
vs ENABLE FREQUENCY CURVE AT V
CC
= 3.3V
12
10
8
I
CCD
(mA)
6
4
2
0
0
2
4
6
8
10
12
14
16
18
20
ENABLE FREQUENCY (MHz)
4
IDTQS3VH862
2.5V / 3.3V 10-BIT ACTIVE HIGH AND LOW ENABLE, HIGH BANDWIDTH BUS SWITCH
INDUSTRIAL TEMPERATURE RANGE
SWITCHING CHARACTERISTICS OVER OPERATING RANGE
T
A
= -40°C to +85°C
V
CC
= 2.5 ± 0.2V
(1)
Symbol
t
PLH
t
PHL
t
PZH
t
PZL
t
PHZ
t
PLZ
f
BE or
BE
Parameter
Data Propagation Delay
(2,3)
A to B or B to A
Switch Turn-On Delay
BE
or BE to xA or xB
Switch Turn-Off Delay
BE
or BE to xA or xB
Operating Frequency - Enable
(2,5)
Min
.
(4)
V
CC
= 3.3 ± 0.3V
(1)
Min
.
(4)
⎯
1.5
1.5
Max.
0.2
7
6.5
20
Unit
ns
ns
ns
MHz
Max.
0.2
8
7
10
⎯
1.5
1.5
⎯
⎯
NOTES:
1. See Test Conditions under TEST CIRCUITS AND WAVEFORMS.
2. This parameter is guaranteed but not production tested.
3. The bus switch contributes no propagation delay other than the RC delay of the ON resistance of the switch and the load capacitance. The time constant for the switch alone is of the
order of 0.2ns at C
L
= 50pF. Since this time constant is much smaller than the rise and fall times of typical driving signals, it adds very little propagation delay to the system. Propagation
delay of the bus switch, when used in a system, is determined by the driving circuit on the driving side of the switch and its interaction with the load on the driven side.
4. Minimums are guaranteed but not production tested.
I want to make a constant temperature heating element that can swing or rotate regularly, similar to the solar-powered swinging flower on a car, but I want this swinging object to generate heat at a c...
Dear heroes: I modified the content of shell.reg as follows: [HKEY_LOCAL_MACHINE\init] ;"Launch50"="explorer.exe" ;"Depend50"=hex:14,00, 1e,00 "Launch200"="player.exe" "Depend200"=hex:14,00, 1e,00 My ...
Last week, we introduced how to use a TF card on the ESP32 learning board. However, because the resistors on the development board were not soldered, the use of the TF card was affected. Therefore, we...
Recently I used a test box at school. The chip is CYCLONE III, and there is an AT080TN52 TFT LCD on it. I want to use VHDL to directly drive and display an image, but I don't know how to achieve it. P...
I wrote a 2-to-1 multiplexer in VHDL. After compiling, I created a new "vector waveform file" to practice waveform simulation, and found that the output waveform seemed to have a time delay. After loo...
The core of a machine vision system is image acquisition and processing. All information comes from images, and image quality is crucial to the entire vision system. A good image can improve the st...[Details]
When we travel in cities, we all find that electric vehicles have many advantages. As a means of transportation, they can also fulfill their mission well. Now, more and more residential communities...[Details]
Limited vocabulary recognition
According to the number of characters, words or short sentences in the vocabulary, it can be roughly divided into: less than 100 is small vocabulary; 100-1000 is...[Details]
In mobile technology, sensors are the primary input for measured signals and form a component of a sensor system. They include sensitive and transducer elements connected to carriers and circuits. ...[Details]
On August 21st, Zhiyuan Robotics revealed at its first partner conference that it expects shipments to reach thousands of units this year and tens of thousands next year. The company hopes to reach...[Details]
Linear motor modules have become the "sweet spot" in various fields due to their advantages such as long stroke, fast speed, high precision, smooth operation and long life. Different models of line...[Details]
The MCX E series is the most reliability- and safety-focused series in NXP's extensive MCX product portfolio.
With the launch of this series, NXP has further enriched its 5V-compatible MCU pr...[Details]
In the period after the switching power supply achieved the "20 kHz" revolution in the 1970s, although improvements and enhancements were made in circuit technology, the development level of the se...[Details]
MQTT Ethernet I/O modules primarily collect I/O port information and transmit data over the network. In addition to being a TCP server, Ethernet I/O modules can also function as TCP clients. Furthe...[Details]
As the range of electric vehicles continues to increase, driving electric vehicles for long-distance travel has become a trend. For high-speed travel, how much impact will high-speed driving of ele...[Details]
The driving mode is not unfamiliar to vehicles. According to the driving mode of the vehicle, there are front-wheel drive, rear-wheel drive and even four-wheel drive. Four-wheel drive is a major se...[Details]
Electric vehicles will revolutionize transportation, changing fuel consumption, carbon emissions, costs, maintenance, and driving habits. Currently, a major selling point for electric vehicles is t...[Details]
As a pioneer in the new smart home concept, robot vacuums have captured a significant market share. Robot vacuums, also known as automatic sweepers, smart vacuums, or robot vacuums, are smart home ...[Details]
introduction
With the development of society, people's requirements for the quality of refrigerated and frozen foods are constantly improving. The changes in food appearance and nutritional co...[Details]
The mobile computing market is rapidly evolving, and manufacturers are fiercely competing for market share. A key area of competition is battery life, which encompasses two key aspects: how long th...[Details]
Energy Infrastructure?
京公网安备 11010802033920号
EEWORLD
