www.make-ps.com
E-mail:info@make-ps.com
2000 series
F
EATURES
•
•
•
•
•
•
•
•
Single, Dual, Triple Output
DC/DC Converter
6 sided Continuous Shielding
Synchronization and Output Trim
Wide 2:1 Input Voltage Range
Efficiency to 86%
UL 1950 Approved
CSA 22.9-950 Approved
VDE / EN 60950 Approved
>700,000 Hours MTBF
D
ESCRIPTIONS
The 2000 series is a family of compact 20 W, high
performance DC/DC converters. These converters are
specifically designed to provide the flexibility, power density,
and reliability required to fulfill local power needs in
applications ranging from telecom switch systems to
portable instrumentation. 24 models operate over 2:1 input
ranges of 9 to 18, 18 to 36 or 36 to 72 VDC; providing single,
dual or triple output combinations of 5, 6, 12, 15, ±12, ±15,
5±12 and 5±15 VDC. All models are packaged in compact,
low profile 3.0” X 2.56” X 0.75” metal cases.
I
NPUT
C
HARACTERISTICS
Min Typ Max Unit/Comments
Input Voltage Range
12 VDC Input Models
9
12
24 VDC Input Models
18 24
48 VDC Input Models
36 48
Remote ON / OFF Control
Supply ON
Supply OFF
Logic Referenced to Negative Input
Input Filter
18
36
72
VDC
VDC
VDC
5.5 VDC or Open Circuit
0 VDC to 0.8 VDC
Pi Filter
O
UTPUT
C
HARACTERISTICS
Min Typ Max Unit/Comments
Output Voltage Accuracy
Single & Dual Outputs
Triple Outputs - Primary
- Auxiliaries
Output Voltage Adjustment
Voltage Balance:
Dual Outputs
Triple Outputs (Auxiliaries)
Minimum Load
Line Regulation
Single Outputs
Dual Outputs
Triple Outputs - Primary
- Auxiliaries
Load Regulation
Single Outputs
Dual Outputs
Triple Outputs - Primary
- Auxiliaries
Ripple/Noise
Single & Dual Output
Triple Output Models
Primary
Auxiliaries
Short Circuit Protection
Transient Recovery Time
Temperature Coefficient
Over Voltage Protection
±1.0
±1.0
±6.0
±5.0
%
1
%
1
%
1
%
1
;
G
ENERAL
C
HARACTERISTICS
Switching Frequency
Isolation Voltage
Isolation Resistance
MTBF (MIL-HBK-217F)
Min Typ Max Unit/Comments
kHz
100
VDC, 1 minute
500
Mohm, 500VDC
1000
Thousand Hours,
700
+25
o
C, Ground
Benign
±0.5 %; Equal Output Loads
±50 mV; Equal Output Loads
10% Full Load
±0.5
±0.4
±0.2
±1.0
±0.5
±0.5
±0.5
±5.0
%
2
%
2
%
2
%
2
%
3
%
3
; Equal Loads
%
3
%
3
; Equal Loads
±1.0 % Pk-Pk of Vout
100mV Pk-Pk
±1.0 % Pk-Pk of Vout
Continuous, Automatic
Recovery
100 uS to within 1% error
band for 50% step
load change
±0.02 % per
o
C
See Model Selection Guide
1
2
3
= Output voltage at nominal line & FL
= % Output voltage measured from min. input line to maximum
= Output voltage measured from FL to 10% Load
>> 1
www.make-ps.com
E
NVIRONMENTAL
S
PECIFICATIONS
Operating Temp. Range
Storage Temp. Range
Relative Humidity
Cooling
Min
-30
-40
Typ Max
+75
+125
95
Unit/Comments
o
C; Ambient
o
C
% Humidity; non-
condensing
Free-Air Convection
E-mail:info@make-ps.com
P
HYSICAL
C
HARACTERISTICS
Case Size
Case Material
Shield Connection
12V and 24V Input Models
48V Input Models
Flammability
Weight
Unit/Comments
2.56 X 3.0 X 0.75 inches
(65.0 X 76.2 X 19.1 mm)
Coated Metal with Non-
Conductive Base
Negative Input
Positive Input
UL94V-0
227 Grams
O
UTLINE
D
RAWING
C
ASE
G
2.56 (65.0)
0.40 0.40 0.40 0.50 0.30 0.30
(10.2) (10.2) (10.2) (12.7) (7.6) (7.6)
0.20
(5.1)
0.040±.005
(1.01)
DIA.
P
IN
O
UT
C
HART
; C
ASE
G
Single
Triple
Dual
Pin
Remote On/Off Remote On/Off Remote On/Off
1
+ Vin
+ Vin
+ Vin
2
- Vin
- Vin
- Vin
3
Sync
Sync
Sync
4
+ Vout (Aux)
+ Vout
5 +Sense/Trim(Down)*
Output Trim
Common(Aux)
Common
6
- Vout (Aux)
- Vout
7 - Sense/Trim (Up)*
+ Vout*
+ Vout (Primary)
Output Trim
8
- Vout*
- Vout (Primary)
No Pin
9
No Pin
Output Trim (Primary)
No Pin
10
* Connections for single output models without sensing or external trimming:
For proper operation, externally connect Pin 5 (+Sense) to Pin 8 (+Vout)
and Pin 7 (-Sense) to Pin 9 (-Vout)
0.75
(19.1)
10
9
8
1.00
(25.4)
7
6
5
BOTTOM
3.00
(76.2)
1.25
(31.75)
2
1
0.30
(7.6)
0.02 MIN.
(0.5)
SIDE
See Note 2
0.72
(18.3)
4
3
0.70
(17.8)
0.40 0.40 0.60
(10.2) (10.2) (15.2)
0.25
(6.4)
Notes:
1. Unless otherwise specified dimensions are in inches (mm).
Tolerances
Inches
mm
X.XX = ±0.02
X.X = ±0.5
X.XXX= ±0.010
X.XX = ±0.25
2. Mounting inserts: 4-40 X .10 (2.5) Deep
All specifications are typical at nominal input, nominal load and 25
°
C unless otherwise specified.
External, low ESR, 10 microfarad (minimum) capacitor across output is recommended for operation.
>> 2
This datasheet has been downloaded from:
www.EEworld.com.cn
Free Download
Daily Updated Database
100% Free Datasheet Search Site
100% Free IC Replacement Search Site
Convenient Electronic Dictionary
Fast Search System
www.EEworld.com.cn
All Datasheets Cannot Be Modified Without Permission
Copyright © Each Manufacturing Company
MCU
京公网安备 11010802033920号
EEWORLD
