PH1-MLALCTD51 datasheet, PDF - EEWORLD Datasheet

Datasheet> All Categories > Wireless rf/communication> Optical fiber> PH1-MLALCTD51

PH1-MLALCTD51: DescriptionTransponder, 10709Mbps(Tx), 10709Mbps(Rx), LC/SPC Connector,; CategoryWireless rf/communication Optical fiber; File Size240KB，6 Pages; ManufacturerLumentum Operations LLC

Download Datasheet Parametric View All

PH1-MLALCTD51 Overview

Transponder, 10709Mbps(Tx), 10709Mbps(Rx), LC/SPC Connector,

PH1-MLALCTD51 Parametric

Parameter Name	Attribute value
Maker	Lumentum Operations LLC
Reach Compliance Code	compliant
Other features	IT ALSO OPERATE FROM 1280NM TO 1600NM
body height	13.2 mm
Body length or diameter	84.1 mm
Connection Type	LC/SPC CONNECTOR
Data rate (receive)	10709 Mbps
Data rate (send)	10709 Mbps
Emitter/Detector Type	AVALANCHE PHOTODIODE
Fiber optic equipment types	TRANSCEIVER, TRANSPONDER
Nominal operating wavelength	1550 nm
Nominal optical power output	1.584 mW
minimum return loss	-27 dB
Sensitivity	-24 dBm

Preview

Download Datasheet

View All

COMMUNICATIONS MODULES & SUBSYSTEMS

10 Gb/s TDM/DWDM 300 Pin SFF MSA SR2/IR2/LR2 Transponder

PH1 Series

Key Features

• Three configurations supporting SR2/IR2/LR2 applications

• Supports dense wavelength division multiplexing

(DWDM) applications (without wavelocker)

• Microprocessor controls to support I2C

• Integrated 16:1/1:16 mux/demux

• Small form factor package (2.2" x 3.0" x 0.53") for high

density applications

• Low power consumption: 4.8 W typical, 6.8 W maximum

for TDM applications

• 70 °C maximum operating temperature

• High sensitivity PIN or APD receivers

• SONET, FEC, Ethernet and Multirate Capable Versions

• Forward, counter and line timing clocking modes

Applications

•

Telecommunications

Metropolitan Area Networks

Subscriber loop

Intra-office SONET/SDH

High bit-rate data communications

JDSU 10 Gb/s PH1 Series transponders are intended for 1550 nm system

applications with reaches of up to 80 km. The series includes three different

transponders for SR2 (25 km), IR2 (40 km), and LR2 (80 km) TDM or DWDM

applications. Each transponder accepts 16 bits of parallel digital data and converts

it to a 10 Gb/s NRZ modulated optical signal. It also accepts a 10 Gb/s NRZ

modulated optical signal and converts it into 16 bit wide parallel digital data.

The PH1 series offers low DC power dissipation and is available in either a small

form factor package (2.2 x 3 x 0.53 inches) or in a larger footprint (3.5 x 4.5 x 0.53

inches) package, depending on system thermal performance requirements. The

transmit design uses an Electro-Absorptive Modulated Laser (EML) which,

depending on the configuration, produces an average output power of between

-4 dBm to 2 dBm (EOL). A PIN (-17 dBm typical sensitivity) or APD (-24 dBm

typical sensitivity) receiver is available, based on system configurations.

JDSU PH1 Series transponders are designed to support the following data rates:

9.953 Gb/s (SONET), 10.3125 Gb/s (Ethernet), 10.664 Gb/s (FEC Encoded),

10.709 Gb/s FEC, or 11.09 Gb/s EFEC. They meet all applicable SONET/SDH standards.

Compliance

• Telcordia GR-253-Core

NORTH AMERICA

800 498-JDSU (5378)

WORLDWIDE

+800 5378-JDSU

WEBSITE

www.jdsu.com

Recommended Resources

Frequency conversion circuit of satellite receiver

Electronic stable speed motor application circuit

Integrator basic circuit

Power supply filter circuit that can suppress high-frequency interference

Multifunctional motor protection circuit

Microcontroller test board circuit 2

Please tell me how to determine whether a certain bit of a port reads 0: I encountered a problem when doing a DHT11 reading experiment, that is, how to determine whether the IO line reads 0? I used #define IO_READ_H PIND |= (1 If you can judge 1, you can judge 0. Think abo...; whg0109 Microchip MCU

【SensorTag】Why is my SensorTag not responding?: Use TI's BLE Device Monitor program and connect to the computer via the serial port. The interface is as follows:Do I have to use flow control for the RX and TX in the UART I use?...; dontium Wireless Connectivity

Questions about DC: The synthesis includes pads, but whether special constraints are required for the pads; without any processing, the compile_ultra report is as follows: report_timing indicates that the pad capacitance...; eeleader FPGA/CPLD

I need some small projects to participate in the competition. I would like to ask for support. Thank you very much for your help and suggestions.: Quick help...; 风醉竹林 51mcu

Regarding the movement of the stepper motor controlled by 8255A, the simulation cannot be done. Please give me some advice. The program is attached.: I am working on a project now, part of which is to use port A of 8255 to control the movement of a stepper motor. The timer 0 interrupt method is adopted, that is, every time an interrupt is entered, ...; zhf120 MCU

Delphi Serial Port: [i=s] This post was last edited by paulhyde on 2014-9-15 09:35 [/i] I practiced writing the serial communication part when programming the host computer. I hope it will be helpful to students who use ...; bluelool1 Electronics Design Contest

Shortcut: A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 AA AB AC AD AE AF AG AH AI AJ AK AL AM AN AO AP AQ AR AS AT AU AV AW AX AY AZ B0 B1 B2 B3 B4 B5 B6 B7 B8 B9 BA BB BC BD BE BF BG BH BI BJ BK BL BM BN BO BP BQ BR BS BT BU BV BW BX BY BZ C0 C1 C2 C3 C4 C5 C6 C7 C8 C9 CA CB CC CD CE CF CG CH CI CJ CK CL CM CN CO CP CQ CR CS CT CU CV CW CX CY CZ D0 D1 D2 D3 D4 D5 D6 D7 D8 D9 DA DB DC DD DE DF DG DH DI DJ DK DL DM DN DO DP DQ DR DS DT DU DV DW DX DZ

Popular Components