EEWORLDEEWORLDEEWORLD

Part Number

Search

PH1-MLASC3042

Description
Transponder, 10709Mbps(Tx), 10709Mbps(Rx), SC/UPC Connector,
CategoryWireless rf/communication    Optical fiber   
File Size240KB,6 Pages
ManufacturerLumentum Operations LLC
Download Datasheet Parametric View All

PH1-MLASC3042 Overview

Transponder, 10709Mbps(Tx), 10709Mbps(Rx), SC/UPC Connector,

PH1-MLASC3042 Parametric

Parameter NameAttribute value
MakerLumentum Operations LLC
Reach Compliance Codecompliant
Other featuresIT ALSO OPERATE FROM 1280NM TO 1600NM
body height13.2 mm
Body length or diameter84.1 mm
Connection TypeSC/UPC CONNECTOR
Data rate (receive)10709 Mbps
Data rate (send)10709 Mbps
Emitter/Detector TypeAVALANCHE PHOTODIODE
Fiber optic equipment typesTRANSCEIVER, TRANSPONDER
Nominal operating wavelength1537 nm
Nominal optical power output1.584 mW
minimum return loss-27 dB
Sensitivity-24 dBm
COMMUNICATIONS MODULES & SUBSYSTEMS
10 Gb/s TDM/DWDM 300 Pin SFF MSA SR2/IR2/LR2 Transponder
PH1 Series
Key Features
• Three configurations supporting SR2/IR2/LR2 applications
• Supports dense wavelength division multiplexing
(DWDM) applications (without wavelocker)
• Microprocessor controls to support I2C
• Integrated 16:1/1:16 mux/demux
• Small form factor package (2.2" x 3.0" x 0.53") for high
density applications
• Low power consumption: 4.8 W typical, 6.8 W maximum
for TDM applications
• 70 °C maximum operating temperature
• High sensitivity PIN or APD receivers
• SONET, FEC, Ethernet and Multirate Capable Versions
• Forward, counter and line timing clocking modes
Applications
Telecommunications
Metropolitan Area Networks
Subscriber loop
Intra-office SONET/SDH
High bit-rate data communications
JDSU 10 Gb/s PH1 Series transponders are intended for 1550 nm system
applications with reaches of up to 80 km. The series includes three different
transponders for SR2 (25 km), IR2 (40 km), and LR2 (80 km) TDM or DWDM
applications. Each transponder accepts 16 bits of parallel digital data and converts
it to a 10 Gb/s NRZ modulated optical signal. It also accepts a 10 Gb/s NRZ
modulated optical signal and converts it into 16 bit wide parallel digital data.
The PH1 series offers low DC power dissipation and is available in either a small
form factor package (2.2 x 3 x 0.53 inches) or in a larger footprint (3.5 x 4.5 x 0.53
inches) package, depending on system thermal performance requirements. The
transmit design uses an Electro-Absorptive Modulated Laser (EML) which,
depending on the configuration, produces an average output power of between
-4 dBm to 2 dBm (EOL). A PIN (-17 dBm typical sensitivity) or APD (-24 dBm
typical sensitivity) receiver is available, based on system configurations.
JDSU PH1 Series transponders are designed to support the following data rates:
9.953 Gb/s (SONET), 10.3125 Gb/s (Ethernet), 10.664 Gb/s (FEC Encoded),
10.709 Gb/s FEC, or 11.09 Gb/s EFEC. They meet all applicable SONET/SDH standards.
Compliance
• Telcordia GR-253-Core
NORTH AMERICA
:
800 498-JDSU (5378)
WORLDWIDE
:
+800 5378-JDSU
WEBSITE
:
www.jdsu.com
Several boards and an MP4, 430, Cortex-M0
[i=s]This post was last edited by Shi Yu on 2014-8-17 13:41[/i] I don't play with 430 anymore. I gave away all my books last month. The board has been gathering dust for a long time. I need to save mo...
石玉 Buy&Sell
Texas Instruments - Using an Op Amp as a Comparator - Is It Possible?
[i=s]This post was last edited by dontium on 2015-1-23 12:47[/i] [color=#000000][font=宋体][size=12pt]Many people occasionally use op amps as comparators. Generally speaking, this works when you just ne...
德州仪器 Analogue and Mixed Signal
After 220VAC is converted to 15VDC and a load is added, the output voltage is incorrect. What component problem could this be?
Using DM0265R, the 15V output is correct when no load is applied, but after adding load (a motor), the 15V output becomes more than 3V. The problem is that some boards are good, while others are fault...
ldsheng Power technology
MCU selection
For the selection of MCU , SCT12 2052/4052 can be used for learning , which is easy to program. If you want to make a micro-power-saving sparrow type, you can choose the MSP430 series....
bjwl_6338 DIY/Open Source Hardware
Director Tony Testa teaches you how to design products for Wi-Fi 6
[i=s]This post was last edited by alan000345 on 2019-11-28 09:21[/i]Do you know how to design applications for Wi-Fi 6?Experts who support Wi-Fi point out that the launch of the Wi-Fi 6 standard will ...
alan000345 RF/Wirelessly
Group G Code
[i=s] This post was last edited by paulhyde on 2014-9-15 03:27 [/i] I can't understand the code I bought on Taobao. Please share it with me....
奋斗了 Electronics Design Contest

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 973  2882  394  1224  2045  20  59  8  25  42 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号